Receiver Front-Ends in CMOS with Ultra-Low Power Consumption

Historically, research on radio communication has focused on improving range and data rate. In the last decade, however, there has been an increasing demand for low power and low cost radios that can provide connectivity with small devices around us. They should be able to offer basic connectivity with a power consumption low enough to function extended periods of time on a single battery charge, or even energy scavenged from the surroundings. This work is focused on the design of ultra-low power receiver front-ends intended for a receiver operating in the 2.4GHz ISM band, having an active power consumption of 1mW and chip area of 1mm². Low power consumption and small size make it hard to achieve good sensitivity and tolerance to interference. This thesis starts with an introduction to the overall receiver specifications, low power radio and radio standards, front-end and LO generation architectures and building blocks, followed by the four included papers. Paper I demonstrates an inductorless front-end operating at 915MHz, including a frequency divider for quadrature LO generation. An LO generator operating at 2.4GHz is shown in Paper II, enabling a front-end operating above 2GHz. Papers III and IV contain circuits with combined front-end and LO generator operating at or above the full 2.45GHz target frequency. They use VCO and frequency divider topologies that offer efficient operation and low quadrature error. An efficient passive-mixer design with improved suppression of interference, enables an LNA-less design in Paper IV capable of operating without a SAW-filter

Vibration energy harvesters for wireless sensor networks for aircraft health monitoring

Traditional power supply for wireless sensor nodes is batteries. However, the application of batteries in WSN has been limited due to their large size, low capacity, limited working life, and replacement cost. With rapid advancements in microelectronics, power consumption of WSN is getting lower and hence the energy harvested from ambient may be sufficient to power the tiny sensor nodes and eliminate batteries completely. As vibration is the widespread ambient source that exists in abundance on an aircraft, a WSN node system used for aircraft health monitoring powered by a piezoelectric energy harvester was designed and manufactured. Furthermore, simulations were performed to validate the design and evaluate the performance. In addition, the Z-Stack protocol was migrated to run on the system and initial experiments were carried out to analyse the current consumption of the system. A new approach for power management was reported, the execution of the operations were determined by the amount of the energy stored on the capacitor. A novel power saving interface was also developed to minimise the power consumption during the voltage measurement

Design of an Ultra Low Power RFCMOS Transceiver for a Self-Powered IoT Node

In this thesis a transceiver characterized to consume ultra low power based in RFCMOS for a self-powered Internet of Things node is studied and designed. The transceiver consists in a simple Non-Coherent system, which means that the signal is picked up by the receiver based on energy detection, as a result it is one of the simplest existing transceivers once it does not need in the transmitter a complex pulse generator and certainly in the receiver as well. It is composed by an OOK modulator, a pulse generator that will determine the centre frequency and a driver amplifier connected to a 50W antenna for the transmitter. While in the receiver there is as first block a Low Noise Amplifier, a self-mixer that will prepare the signal for the integrator and a comparator working as a energy detector. The UWB transceiver will be able to operate with a centre frequency of 4.5 GHz and a bandwidth of at least 500 MHz. It is critical to notice that the system is consuming a value of 96 mW for the power and accomplishing the power spectrum density -43 dBm/MHz using an OOK modulation technique. The entire system was implemented with standard 130nm CMOS technology

Millimeter-Scale and Energy-Efficient RF Wireless System

This dissertation focuses on energy-efficient RF wireless system with millimeter-scale dimension, expanding the potential use cases of millimeter-scale computing devices. It is challenging to develop RF wireless system in such constrained space. First, millimeter-sized antennae are electrically-small, resulting in low antenna efficiency. Second, their energy source is very limited due to the small battery and/or energy harvester. Third, it is required to eliminate most or all off-chip devices to further reduce system dimension. In this dissertation, these challenges are explored and analyzed, and new methods are proposed to solve them. Three prototype RF systems were implemented for demonstration and verification. The first prototype is a 10 cubic-mm inductive-coupled radio system that can be implanted through a syringe, aimed at healthcare applications with constrained space. The second prototype is a 3x3x3 mm far-field 915MHz radio system with 20-meter NLOS range in indoor environment. The third prototype is a low-power BLE transmitter using 3.5x3.5 mm planar loop antenna, enabling millimeter-scale sensors to connect with ubiquitous IoT BLE-compliant devices. The work presented in this dissertation improves use cases of millimeter-scale computers by presenting new methods for improving energy efficiency of wireless radio system with extremely small dimensions. The impact is significant in the age of IoT when everything will be connected in daily life.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/147686/1/yaoshi_1.pd

Energy-Efficient Wireless Circuits and Systems for Internet of Things

As the demand of ultra-low power (ULP) systems for internet of thing (IoT) applications has been increasing, large efforts on evolving a new computing class is actively ongoing. The evolution of the new computing class, however, faced challenges due to hard constraints on the RF systems. Significant efforts on reducing power of power-hungry wireless radios have been done. The ULP radios, however, are mostly not standard compliant which poses a challenge to wide spread adoption. Being compliant with the WiFi network protocol can maximize an ULP radio’s potential of utilization, however, this standard demands excessive power consumption of over 10mW, that is hardly compatible with in ULP systems even with heavy duty-cycling. Also, lots of efforts to minimize off-chip components in ULP IoT device have been done, however, still not enough for practical usage without a clean external reference, therefore, this limits scaling on cost and form-factor of the new computer class of IoT applications. This research is motivated by those challenges on the RF systems, and each work focuses on radio designs for IoT applications in various aspects. First, the research covers several endeavors for relieving energy constraints on RF systems by utilizing existing network protocols that eventually meets both low-active power, and widespread adoption. This includes novel approaches on 802.11 communication with articulate iterations on low-power RF systems. The research presents three prototypes as power-efficient WiFi wake-up receivers, which bridges the gap between industry standard radios and ULP IoT radios. The proposed WiFi wake-up receivers operate with low power consumption and remain compatible with the WiFi protocol by using back-channel communication. Back-channel communication embeds a signal into a WiFi compliant transmission changing the firmware in the access point, or more specifically just the data in the payload of the WiFi packet. With a specific sequence of data in the packet, the transmitter can output a signal that mimics a modulation that is more conducive for ULP receivers, such as OOK and FSK. In this work, low power mixer-first receivers, and the first fully integrated ultra-low voltage receiver are presented, that are compatible with WiFi through back-channel communication. Another main contribution of this work is in relieving the integration challenge of IoT devices by removing the need for external, or off-chip crystals and antennas. This enables a small form-factor on the order of mm3-scale, useful for medical research and ubiquitous sensing applications. A crystal-less small form factor fully integrated 60GHz transceiver with on-chip 12-channel frequency reference, and good peak gain dual-mode on-chip antenna is presented.PHDElectrical and Computer EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/162975/1/jaeim_1.pd

Low power digitally controlled oscillator for IoT applications

This work is focused on the design of a Low Power CMOS DCO for IEEE 802.11ah in IoT applications. The design methodology is based on the Unified current-control model (UICM), which is a physics-based model and enables an accurate all-region model of the operation of the device. Additionally, a transformer-based resonator has been used to solve the low-quality factor issue of integrated inductors. Two digitally controlled oscillators (DCO) have been implemented to show the advantages of utilizing a transformedbased resonator and the methodology based on the UICM model. These designs aim for the operation in low voltage supply (VDD) since VDD scaling is a trend in systems-onchip (SoCs), in which the circuitry is mostly digital. Despite the degradation caused by VDD scaling, new RF and analog circuits must deliver similar performance of the older CMOS nodes. The first DCO design was a low power LC-tank DCO, implemented in 40nm bulk-CMOS. The first design presented a DCO operating at 45% of the nominal VDD without compromise the performance. By reducing the VDD below the nominal value, this DCO reduces power consumption, which is a crucial feature for IoT circuits. The main contribution of this first DCO is the reduction of VDD scaling impact on the phase-noise do the DCO. The LC-based DCO operates from 1.8 to 1.86 GHz. At the maximum frequency and 0.395V VDD, the power consumption is a mere 380 W with a phase-noise of -119.3 dBc/Hz at 1 MHz. The circuit occupies an area of 0.46mm2 in 40 nm CMOS, mostly due to the inductor. The second DCO design was a low-power transformer-based DCO design, implemented in 28nm bulk-CMOS. This second design aims for the VDD reduction to below 0.3 V. Operating in a frequency range similar to the LC-based DCO, the transformer-based DCO operated with 0.280V VDD with a power consumption of 97 W. Meanwhile, the phase-noise was -101.95 dBc/Hz at 1 MHz. Even in the worst-case scenario (i.e., slow-slow and 85oC), this second DCO was able to operate at 0.330V VDD, consuming 126 W, while it keeps a similar phase-noise performance of the typical case. The core circuit occupies an area of 0.364 mm2.Este trabalho objetiva o projeto de um DCO de baixa potência em CMOS para aplicações de IoT e aderentes ao padrão IEEE 802.11ah. A metodologia de projeto é baseada no modelo de controle de corrente unificado (UICM), que é um modelo com embasamento físico que permite uma operação precisa em todas as regiões de operação do dispositivo. Adicionalmente, é utilizado um ressonador baseado em transformador visando solucionar os problemas provenientes do baixo fator de qualidade de indutores integrados. Para destacar as melhorias obtidas com o projeto do ressonador baseado em transformador e com a metodologia baseada no modelo UICM, dois projetos de DCO são realizados. Esses projetos visam a operação com baixa tensão de alimentação (VDD), uma vez que o escalonamento do VDD é uma tendência em sistemas em chip (SoCs), em que o circuito é majoritariamente digital. Independente da degradação causada pelo escalonamento de VDD, circuitos analógicos e de RF atuais devem oferecer desempenho semelhante ao alcançado em tecnologias CMOS mais antigas. O primeiro projeto foi um DCO de baixa potência com tanque LC, implementado em tecnologia bulk-CMOS de 40nm. O primeiro projeto apresentou uma operação a 45% do VDD nominal sem comprometer o desempenho. Ao reduzir o VDD abaixo do valor nominal, este DCO reduz o consumo de energia, que é uma característica crucial para circuitos IoT. A principal contribuição deste DCO é a redução do impacto do escalonamento do VDD no ruído de fase. O DCO com tanque LC opera de 1,8 a 1,86 GHz. Na frequência máxima e com VDD de apenas 0,395V, o consumo de energia é 380 W e o ruído de fase é -119,3 dBc/Hz a 1 MHz. O circuito ocupa uma área de 0.46mm2 em processo CMOS de 40 nm. O segundo projeto foi um DCO de baixa potência baseado em transformador, implementado em tecnologia bulk- CMOS de 28nm. Este projeto visa a redução de VDD abaixo de 0,3 V. Operando em uma faixa de frequência semelhante ao primeiro DCO, o DCO baseado em transformador opera com VDD de 0,280V e com consumo de potência de 97 W. O ruído de fase foi de -101,95 dBc/Hz a 1 MHz. Mesmo no pior caso de processo, este DCO opera a um VDD de 0,330V, consumindo 126 W, com o ruído de fase semelhante ao caso típico. O circuito ocupa uma área de 0.364mm2

Low Power Circuit Design in Sustainable Self Powered Systems for IoT Applications

The Internet-of-Things (IoT) network is being vigorously pushed forward from many fronts in diverse research communities. Many problems are still there to be solved, and challenges are found among its many levels of abstraction. In this thesis we give an overview of recent developments in circuit design for ultra-low power transceivers and energy harvesting management units for the IoT. The first part of the dissertation conducts a study of energy harvesting interfaces and optimizing power extraction, followed by power management for energy storage and supply regulation. we give an overview of the recent developments in circuit design for ultra-low power management units, focusing mainly in the architectures and techniques required for energy harvesting from multiple heterogeneous sources. Three projects are presented in this area to reach a solution that provides reliable continuous operation for IoT sensor nodes in the presence of one or more natural energy sources to harvest from. The second part focuses on wireless transmission, To reduce the power consumption and boost the Tx energy efficiency, a novel delay cell exploiting current reuse is used in a ring-oscillator employed as the local oscillator generator scheme. In combination with an edge-combiner power amplifier, the Tx showed a measured energy efficiency of 0.2 nJ=bit and a normalized energy efficiency of 3.1 nJ=bit:mW when operating at output power levels up to -10 dBm and data rates of 3 Mbps

RF Integrated Circuits for Energy Autonomous Sensor Nodes.

The exponential growth in the semiconductor industry has enabled computers to pervade our everyday lives, and as we move forward many of these computers will have form factors much smaller than a typical laptop or smartphone. Sensor nodes will soon be deployed ubiquitously, capable of capturing information of their surrounding environment. The next step is to connect all these different nodes together into an entire interconnected system. This “Internet of Things” (IoT) vision has incredible potential to change our lives commercially, societally, and personally. The backbone of IoT is the wireless sensor node, many of which will operate under very rigorous energy constraints with small batteries or no batteries at all. It has been shown that in sensor nodes, radio communication is one of the biggest bottlenecks to ultra-low power design. This research explores ways to reduce energy consumption in radios for wireless sensor networks, allowing them to run off harvested energy, while maintaining qualities that will allow them to function in a real world, multi-user environment. Three different prototypes have been designed demonstrating these techniques. The first is a sensitivity-reduced nanowatt wake-up radio which allows a sensor node to actively listen for packets even when the rest of the node is asleep. CDMA codes and interference rejection reduce the potential for energy-costly false wake-ups. The second prototype is a full transceiver for a body-worn EKG sensor node. This transceiver is designed to have low instantaneous power and is able to receive 802.15.6 Wireless Body Area Network compliant packets. It uses asymmetric communication including a wake-up receiver based on the previous design, UWB transmitter and a communication receiver. The communication receiver has 10 physical channels to avoid interference and demodulates coherent packets which is uncommon for low power radios, but dictated by the 802.15.6 standard. The third prototype is a long range transceiver capable of >1km communication range in the 433MHz band and able to interface with an existing commercial radio. A digitally assisted baseband demodulator was designed which enables the ability to perform bit-level as well as packet-level duty cycling which increases the radio's energy efficiency.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/110432/1/nerobert_1.pd

Energy-Efficient Wireless Connectivity and Wireless Charging For Internet-of-Things (IoT) Applications

During the recent years, the Internet-of-Things (IoT) has been rapidly evolving. It is indeed the future of communication that has transformed Things of the real world into smarter devices. To date, the world has deployed billions of “smart” connected things. Predictions say there will be 10’s of billions of connected devices by 2025 and in our lifetime we will experience life with a trillion-node network. However, battery lifespan exhibits a critical barrier to scaling IoT devices. Replacing batteries on a trillion-sensor scale is a logistically prohibitive feat. Self-powered IoT devices seems to be the right direction to stand up to that challenge. The main objective of this thesis is to develop solutions to achieve energy-efficient wireless-connectivity and wireless-charging for IoT applications. In the first part of the thesis, I introduce ultra-low power radios that are compatible with the Bluetooth Low-Energy (BLE) standard. BLE is considered as the preeminent protocol for short-range communications that support transmission ranges up to 10’s of meters. Number of low power BLE transmitter (TX) and receiver (RX) architectures have been designed, fabricated and tested in different planar CMOS and FinFET technologies. The low power operation is achieved by combining low power techniques in both the network and physical layers, namely: backchannel communication, duty-cycling, open-loop transmission/reception, PLL-less architectures, and mixer-first architectures. Further novel techniques have been proposed to further reduce the power the consumption of the radio design, including: a fast startup time and low startup energy crystal oscillators, an antenna-chip co-design approach for quadrature generation in the RF path, an ultra-low power discrete-time differentiator-based Gaussian Frequency Shift Keying (GFSK) demodulation scheme, an oversampling GFSK modulation/demodulation scheme for open loop transmission/reception and packet synchronization, and a cell-based design approach that allows automation in the design of BLE digital architectures. The implemented BLE TXs transmit fully-compliant BLE advertising packet that can be received by commercial smartphone. In the second part of the thesis, I introduce passive nonlinear resonant circuits to achieve wide-band RF energy harvesting and robust wireless power transfer circuits. Nonlinear resonant circuits modeled by the Duffing nonlinear differential equation exhibit interesting hysteresis characteristics in their frequency and amplitude responses that are exploited in designing self-adaptive wireless charging systems. In the magnetic-resonance wireless power transfer scenario, coupled nonlinear resonators are proposed to maintain the power transfer level and efficiency over a range of coupling factors without active feedback control circuitry. Coupling factor depends on the transmission distance, lateral, and angular misalignments between the charging pad and the device. Therefore, nonlinear resonance extends the efficient charging zones of a wireless charger without the requirement for a precise alignment.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/169842/1/omaratty_1.pd