High-speed Low-voltage CMOS Flash Analog-to-Digital Converter for Wideband Communication System-on-a-Chip

With higher-level integration driven by increasingly complex digital systems and downscaling CMOS processes available, system-on-a-chip (SoC) is an emerging technology of low power, high cost effectiveness and high reliability and is exceedingly attractive for applications in high-speed data conversion wireless and wideband communication systems. This research presents a novel ADC comparator design methodology; the speed and performance of which is not restricted by the supply voltage reduction and device linearity deterioration in scaling-down CMOS processes. By developing a dynamic offset suppression technique and a circuit optimization method, the comparator can achieve a 3 dB frequency of 2 GHz in 130 nanometer (nm) CMOS process. Combining this new comparator design and a proposed pipelined thermometer-Gray- binary encoder designed by the DCVSPG logic, a high-speed, low-voltage clocked-digital- comparator (CDC) pipelined CMOS flash ADC architecture is proposed for wideband communication SoC. This architecture has advantages of small silicon area, low power, and low cost. Three CDC-based pipelined CMOS flash ADCs were implemented in 130 nm CMOS process and their experimental results are reported: 1. 4-b, 2.5-GSPS ADC: SFDR of 21.48-dB, SNDR of 15.99-dB, ENOB of 2.4-b, ERBW of 1-GHz, power of 7.9-mW, and area of 0.022-mm2. 2. 4-b, 4-GSPS ADC: SFDR of 25-dB, SNDR of 18.6-dB, ENOB of 2.8-b, ERBW of 2-GHz, power of 11-mW. 3. 6-b, 4-GSPS ADC: SFDR of 48-dB at a signal frequency of 11.72-MHz, SNDR of 34.43-dB, ENOB of 5.4-b, power of 28-mW. An application of the proposed CDC-based pipelined CMOS flash ADC is 1-GHz bandwidth, 2.5-GSPS digital receiver on a chip. To verify the performance of the receiver, a mixed-signal block-level simulation and verification flow was built in Cadence AMS integrated platform. The verification results of the digital receiver using a 4-b 2.5-GSPS CDC-based pipelined CMOS ADC, a 256-point, 12-point kernel function FFT and a frequency detection logic show that two tone signals up to 1125 MHz can be detected and discriminated. A notable contribution of this research is that the proposed ADC architecture and the comparator design with dynamic offset suppression and optimization are extremely suitable for future VDSM CMOS processes and make all-digital receiver SoC design practical

Design and Implementation of a Novel Flash ADC for Ultra Wide Band Applications

This dissertation presents a design and implementation of a novel flash ADC architecture for ultra wide band applications. The advancement in wireless technology takes us in to a world without wires. Most of the wireless communication systems use digital signal processing to transmit as well as receive the information. The real world signals are analog. Due to the processing complexity of the analog signal, it is converted to digital form so that processing becomes easier. The development in the digital signal processor field is rapid due to the advancement in the integrated circuit technology over the last decade. Therefore, analog-to -digital converter acts as an interface in between analog signal and digital signal processing systems. The continuous speed enhancement of the wireless communication systems brings out huge demands in speed and power specifications of high-speed low-resolution analog-to -digital converters. Even though wired technology is a primary mode of communication, the quality and efficiency of the wireless technology allows us to apply to biomedical applications, in home services and even to radar applications. These applications are highly relying on wireless technology to send and receive information at high speed with great accuracy. Ultra Wideband (UWB) technology is the best method to these applications. A UWB signal has a bandwidth of minimum 500MHz or a fractional bandwidth of 25 percentage of its centre frequency. The two different technology standards that are used in UWB are multiband orthogonal frequency division multiplexing ultra wideband technology (MB-OFDM) and carrier free direct sequence ultra wideband technology (DS-UWB). ADC is the core of any UWB receiver. Generally a high speed flash ADC is used in DS-UWB receiver. Two different flash ADC architectures are proposed in this thesis for DS-UWB applications. The first design is a high speed five bit flash ADC architecture with a sampling rate of 5 GS/s. The design is verified using CADENCE tool with CMOS 90 nm technology. The total power dissipation of the ADC is 8.381 mW from power supply of 1.2 V. The die area of the proposed flash ADC is 186 μm × 210 μm (0.039 mm2). The proposed flash ADC is analysed and compared with other papers in the literature having same resolution and it is concluded that it has the highest speed of operation with medium power dissipation. iii The second design is a reconfigurable five bit flash ADC architecture with a sampling rate of 1.25 GS/s. The design is verified using CADENCE tool with UMC 180 nm technology. The total power dissipation of the ADC is 11.71 mW from power supply of 1.8 V. The die area of the implementation is 432 μm × 720 μm (0.31104 mm2). The chip tape out of the proposed reconfigurable flash ADC is made for fabrication

DEVELOPMENT OF AN UWB RADAR SYSTEM

An ultra-wideband radar system is built at the University of Tennessee with the goal to develop a ground penetrating radar (GPR). The radar is required to transmit and receive a very narrow pulse signal in the time domain. The bistatic radar transmits a pulse through an ultrawide spiral antenna and receives the pulse by a similar antenna. Direct sampling is used to improve the performance of the impulse radar allowing up to 1.5 GHz of bandwidth to be used for signal processing and target detection with high resolution. Using direct sampling offers a less complex system design than traditional lower sample rate, super-heterodyne systems using continuous wave or step frequency methods while offering faster results than conventional equivalent time sampling techniques that require multiple data sets and significant post-processing. These two points are particularly important for a system that may be used in the field in potentially dangerous environments. Direct sampling radar systems, while still frequency limited, are continually improving their upper frequencies boundaries due to more power efficient, higher sampling rate analog to digital converters (ADCs) which relates directly to better subsurface resolution for potential target detection

CMOS Data Converters for Closed-Loop mmWave Transmitters

With the increased amount of data consumed in mobile communication systems, new solutions for the infrastructure are needed. Massive multiple input multiple output (MIMO) is seen as a key enabler for providing this increased capacity. With the use of a large number of transmitters, the cost of each transmitter must be low. Closed-loop transmitters, featuring high-speed data converters is a promising option for achieving this reduced unit cost.In this thesis, both digital-to-analog (D/A) and analog-to-digital (A/D) converters suitable for wideband operation in millimeter wave (mmWave) massive MIMO transmitters are demonstrated. A 2 76 bit radio frequency digital-to-analog converter (RF-DAC)-based in-phase quadrature (IQ) modulator is demonstrated as a compact building block, that to a large extent realizes the transmit path in a closed-loop mmWave transmitter. The evaluation of an successive-approximation register (SAR) analog-to-digital converter (ADC) is also presented in this thesis. Methods for connecting simulated and measured performance has been studied in order to achieve a better understanding about the alternating comparator topology.These contributions show great potential for enabling closed-loop mmWave transmitters for massive MIMO transmitter realizations

Aika-digitaalimuunnin laajakaistaisiin aikapohjaisiin analogia-digitaalimuuntimiin

Modern deeply scaled semiconductor processes make the design of voltage-domain circuits increasingly challenging. On the contrary, the area and power consumption of digital circuits are improving with every new process node. Consequently, digital solutions are designed in place of their purely analog counterparts in applications such as analog-to-digital (A/D) conversion. Time-based analog-to-digital converters (ADC) employ digital-intensive architectures by processing analog quantities in time-domain. The quantization step of the time-based A/D-conversion is carried out by a time-to-digital converter (TDC). A free-running ring oscillator -based TDC design is presented for use in wideband time-based ADCs. The proposed architecture aims to maximize time resolution and full-scale range, and to achieve error resilient conversion performance with minimized power and area consumptions. The time resolution is maximized by employing a high-frequency multipath ring oscillator, and the full-scale range is extended using a high-speed gray counter. The error resilience is achieved by custom sense-amplifier -based sampling flip-flops, gray coded counter and a digital error correction algorithm for counter sampling error correction. The implemented design achieves up to 9-bit effective resolution at 250 MS/s with 4.3 milliwatt power consumption.Modernien puolijohdeteknologioiden skaalautumisen seurauksena jännitetason piirien suunnittelu tulee entistä haasteellisemmaksi. Toisaalta digitaalisten piirirakenteiden pinta-ala sekä tehonkulutus pienenevät prosessikehityksen myötä. Tästä syystä digitaalisia ratkaisuja suunnitellaan vastaavien puhtaasti analogisien rakenteiden tilalle. Analogia-digitaalimuunnos (A/D-muunnos) voidaan toteuttaa jännitetason sijaan aikatasossa käyttämällä aikapohjaisia A/D-muuntimia, jotka ovat rakenteeltaan pääosin digitaalisia. Kvantisointivaihe aikapohjaisessa A/D-muuntimessa toteutetaan aika-digitaalimuuntimella. Työ esittelee vapaasti oskilloivaan silmukkaoskillaattoriin perustuvan aika-digitaalimuuntimen, joka on suunniteltu käytettäväksi laajakaistaisessa aikapohjaisessa A/D-muuntimessa. Esitelty rakenne pyrkii maksimoimaan muuntimen aikaresoluution sekä muunnosalueen, sekä saavuttamaan virhesietoisen muunnostoiminnan minimoidulla tehon sekä pinta-alan kulutuksella. Aikaresoluutio on maksimoitu hyödyntämällä suuritaajuista monipolkuista silmukkaoskillaattoria, ja muunnosalue on maksimoitu nopealla Gray-koodi -laskuripiirillä. Muunnosprosessin virhesietoisuus on saavutettu toteuttamalla näytteistys herkillä kiikkuelementeillä, hyödyntämällä Gray-koodattua laskuria, sekä jälkiprosessoimalla laskurin näytteistetyt arvot virheenkorjausalgoritmilla. Esitelty muunnintoteutus saavuttaa 9 bitin efektiivisen resoluution 250 MS/s näytetaajuudella ja 4.3 milliwatin tehonkulutuksella

A Discrete-Time Technique for Linearity Enhancement of Wideband Receivers

A new signal processing technique is introduced to enhance the linearity performance of wideband radio frequency (RF) receivers. The proposed technique combines the advancements in mixer first architectures with a library of binary sequences as local oscillator signals to enable wide instantaneous bandwidth and high linearity for the RF receiver. To do so, N-bit pseudo-random-binary-sequences (PRBS) are used as local oscillator signals. The RF input signal is multiplied with the PRBS at the mixer and then averaged over the full sequence. This in effect reduces the amplitude of the signal and improves the overall linearity of the system. In order to enable full reconstruction of the input signal N channels are used with each employing a shifted version of a PRBS. The effect of the proposed technique on different aspects of the system performance such as noise and linearity is discussed. In addition, the effect of nonidealities stemming from hardware implementation on the overall performance are studied. A prototype integrated circuit (IC) is implemented in 130\,nm CMOS technology to demonstrate the feasibility of the proposed technique. The design procedure of each circuit block is described and simulation results are used to evaluate the performance. The device is fabricated and characterized using a custom data acquisition system. Measurement results show good agreement with the expected values from simulation and analytical analysis. Calibration techniques are introduced to minimize the effect of DC offsets, gain mismatches, and timing skews. Modifications to the implemented CMOS circuit are proposed to enable such calibrations and further enhance the overall performance of the system. The requirements for the precision of calibration techniques are derived and used to find the specifications of circuit block that are designed to enable these techniques. Calibration of DC offsets along with gain mismatches is carried out for the fabricated IC and results are shown. A digitally assisted technique is proposed to enable the calibration of timing skews. In addition, a review of additional implementation shortcomings that can affect the system performance are reviewed. Finally, a conclusion of the dissertation is presented along with potential future work for further enhancement of the system performance

Multi-gigabit CMOS analog-to-digital converter and mixed-signal demodulator for low-power millimeter-wave communication systems

The objective of the research is to develop high-speed ADCs and mixed-signal demodulator for multi-gigabit communication systems using millimeter-wave frequency bands in standard CMOS technology. With rapid advancements in semiconductor technologies, mobile communication devices have become more versatile, portable, and inexpensive over the last few decades. However, plagued by the short lifetime of batteries, low power consumption has become an extremely important specification in developing mobile communication devices. The ever-expanding demand of consumers to access and share information ubiquitously at faster speeds requires higher throughputs, increased signal-processing functionalities at lower power and lower costs. In today’s technology, high-speed signal processing and data converters are incorporated in almost all modern multi-gigabit communication systems. They are key enabling technologies for scalable digital design and implementation of baseband signal processors. Ultimately, the merits of a high performance mixed-signal receiver, such as data rate, sensitivity, signal dynamic range, bit-error rate, and power consumption, are directly related to the quality of the embedded ADCs. Therefore, this dissertation focuses on the analysis and design of high-speed ADCs and a novel broadband mixed-signal demodulator with a fully-integrated DSP composed of low-cost CMOS circuitry. The proposed system features a novel dual-mode solution to demodulate multi-gigabit BPSK and ASK signals. This approach reduces the resolution requirement of high-speed ADCs, while dramatically reducing its power consumption for multi-gigabit wireless communication systems.PhDGee-Kung Chang - Committee Chair; Chang-Ho Lee - Committee Member; Geoffrey Ye Li - Committee Member; Paul A. Kohl - Committee Member; Shyh-Chiang Shen - Committee Membe

Clock Generation Design for Continuous-Time Sigma-Delta Analog-To-Digital Converter in Communication Systems

Software defined radio, a highly digitized wireless receiver, has drawn huge attention in modern communication system because it can not only benefit from the advanced technologies but also exploit large digital calibration of digital signal processing (DSP) to optimize the performance of receivers. Continuous-time (CT) bandpass sigma-delta (ΣΔ) modulator, used as an RF-to-digital converter, has been regarded as a potential solution for software defined ratio. The demand to support multiple standards motivates the development of a broadband CT bandpass ΣΔ which can cover the most commercial spectrum of 1GHz to 4GHz in a modern communication system. Clock generation, a major building block in radio frequency (RF) integrated circuits (ICs), usually uses a phase-locked loop (PLL) to provide the required clock frequency to modulate/demodulate the informative signals. This work explores the design of clock generation in RF ICs. First, a 2-16 GHz frequency synthesizer is proposed to provide the sampling clocks for a programmable continuous-time bandpass sigma-delta (ΣΔ) modulator in a software radio receiver system. In the frequency synthesizer, a single-sideband mixer combines feed-forward and regenerative mixing techniques to achieve the wide frequency range. Furthermore, to optimize the excess loop delay in the wideband system, a phase-tunable clock distribution network and a clock-controlled quantizer are proposed. Also, the false locking of regenerative mixing is solved by controlling the self-oscillation frequency of the CML divider. The proposed frequency synthesizer performs excellent jitter performance and efficient power consumption. Phase noise and quadrature phase accuracy are the common tradeoff in a quadrature voltage-controlled oscillator. A larger coupling ratio is preferred to obtain good phase accuracy but suffer phase noise performance. To address these fundamental trade-offs, a phasor-based analysis is used to explain bi-modal oscillation and compute the quadrature phase errors given by inevitable mismatches of components. Also, the ISF is used to estimate the noise contribution of each major noise source. A CSD QVCO is first proposed to eliminate the undesired bi-modal oscillation and enhance the quadrature phase accuracy. The second work presents a DCC QVCO. The sophisticated dynamic current-clipping coupling network reduces injecting noise into LC tank at most vulnerable timings (zero crossing points). Hence, it allows the use of strong coupling ratio to minimize the quadrature phase sensitivity to mismatches without degrading the phase noise performance. The proposed DCC QVCO is implemented in a 130-nm CMOS technology. The measured phase noise is -121 dBc/Hz at 1MHz offset from a 5GHz carrier. The QVCO consumes 4.2mW with a 1-V power supply, resulting in an outstanding Figure of Merit (FoM) of 189 dBc/Hz. Frequency divider is one of the most power hungry building blocks in a PLL-based frequency synthesizer. The complementary injection-locked frequency divider is proposed to be a low-power solution. With the complimentary injection schemes, the dividers can realize both even and odd division modulus, performing a more than 100% locking range to overcome the PVT variation. The proposed dividers feature excellent phase noise. They can be used for multiple-phase generation, programmable phase-switching frequency dividers, and phase-skewing circuits