An Ultra-Low-Power Oscillator with Temperature and Process Compensation for UHF RFID Transponder

This paper presents a 1.28MHz ultra-low-power oscillator with temperature and process compensation. It is very suitable for clock generation circuits used in ultra-high-frequency (UHF) radio-frequency identification (RFID) transponders. Detailed analysis of the oscillator design, including process and temperature compensation techniques are discussed. The circuit is designed using TSMC 0.18μm standard CMOS process and simulated with Spectre. Simulation results show that, without post-fabrication calibration or off-chip components, less than ±3% frequency variation is obtained from –40 to 85°C in three different process corners. Monte Carlo simulations have also been performed, and demonstrate a 3σ deviation of about 6%. The power for the proposed circuitry is only 1.18µW at 27°C

Novel Resistorless Mixed-Mode PID Controller with Improved Low-Frequency Performance

This paper introduces a new resistorless mixed-mode proportional-integral-derivative (PID) controller. It employs six simple transconductors and only two grounded capacitors. The proposed PID controller offers several advantageous features of resistorless configuration, use of grounded capacitors, independent electronic-tuning characteristic of its parameters, and mixed-mode operation such as current, transimpedance, transadmittance, and voltage modes. The parasitic element effects of the transconductors on the proposed controller are investigated and the improved low-frequency performance of the proposed controller is then discussed. As applications, the proposed controller is demonstrated on two closed-loop systems. The PSPICE simulations with TSMC 0.18µm CMOS process and ±0.9V supply voltage verify the theoretical analysis

The BLIXER, a Wideband Balun-LNA-I/Q-Mixer Topology

This paper proposes to merge an I/Q current-commutating mixer with a noise-canceling balun-LNA. To realize a high bandwidth, the real part of the impedance of all RF nodes is kept low, and the voltage gain is not created at RF but in baseband where capacitive loading is no problem. Thus a high RF bandwidth is achieved without using inductors for bandwidth extension. By using an I/Q mixer with 25% duty-cycle LO waveform the output IF currents have also 25% duty-cycle, causing 2 times smaller DC-voltage drop after IF filtering. This allows for a 2 times increase in the impedance level of the IF filter, rendering more voltage gain for the same supply headroom. The implemented balun-LNA-I/Q-mixer topology achieves > 18 dB conversion gain, a flat noise figure < 5.5 dB from 500 MHz to 7 GHz, IIP2 = +20 dBm and IIP3 = -3 dBm. The core circuit consumes only 16 mW from a 1.2 V supply voltage and occupies less than 0.01 mm2 in 65 nm CMOS

Realization of Low-Voltage Modified CBTA and Design of Cascadable Current-Mode All-Pass Filter

In this paper, a low voltage modified current backward transconductance amplifier (MCBTA) and a novel first-order current-mode (CM) all-pass filter are presented. The MCBTA can operate with ±0.9 V supply voltage and the total power consumption of MCBTA is 1.27 mW. The presented all-pass filter employs single MCBTA, a grounded resistor and a grounded capacitor. The circuit possesses low input and high output impedances which make it ideal for current-mode systems. The presented all-pass filter circuit can be made electronically tunable due to the bias current of the MCBTA. Non-ideal study along with simulation results are given for validation purpose. Further, an nth-order cascadable all-pass filter is also presented. It uses n MCBTAs, n grounded resistors and n grounded capacitors. The performance of the proposed circuits is demonstrated by using PSPICE simulations based on the 0.18 µm TSMC level-7 CMOS technology parameters

A 0.18µm CMOS DDCCII for Portable LV-LP Filters

In this paper a current mode very low voltage (LV) (1V) and low power (LP) (21 µW) differential difference second generation current conveyor (CCII) is presented. The circuit is developed by applying the current sensing technique to a fully balanced version of a differential difference amplifier (DDA) so to design a suitable LV LP integrated version of the so-called differential difference CCII (DDCCII). Post-layout results, using a 0.18µm SMIC CMOS technology, have shown good general circuit performances making the proposed circuit suitable for fully integration in battery portable systems as, for examples, fully differential Sallen-Key bandpass filter

Voltage-Mode Multifunction Biquadratic Filters Using New Ultra-Low-Power Differential Difference Current Conveyors

This paper presents two low-power voltage-mode multifunction biquadratic filters using differential difference current conveyors. Each proposed circuit employs three differential difference current conveyors, two grounded capacitors and two grounded resistors. The low-voltage ultra-low-power differential difference current conveyor is used to provide low-power consumption of the proposed filters. By appropriately connecting the input and output terminals, the proposed filters can provide low-pass, band-pass, high-pass, band-stop and all-pass voltage responses at high-input terminals, which is a desirable feature for voltage-mode operations. The natural frequency and the quality factor can be orthogonally set by adjusting the circuit components. For realizing all the filter responses, no inverting-type input signal requirements as well as no component-matching conditional requirements are imposed. The incremental parameter sensitivities are also low. The characteristics of the proposed circuits are simulated by using PSPICE simulators to confirm the presented theory

Voltage-Mode Highpass, Bandpass, Lowpass and Notch Biquadratic Filters Using Single DDCC

A new voltage-mode multifunction biquadratic filter using one differential difference current conveyor (DDCC), two grounded capacitors and three resistors is presented. The proposed circuit offers the following attractive advantages: realizing highpass, bandpass, lowpass and notch filter functions, simultaneously, from the same circuit configuration; employing grounded capacitors, which is ideal for integration and simpler circuit configuration

Single-amplifier integrator-based low power CMOS filter for video frequency applications

“This material is presented to ensure timely dissemination of scholarly and technical work. Copyright and all rights therein are retained by authors or by other copyright holders. All persons copying this information are expected to adhere to the terms and constraints invoked by each author's copyright. In most cases, these works may not be reposted without the explicit permission of the copyright holder." “Copyright IEEE. Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse any copyrighted component of this work in other works must be obtained from the IEEE.”This paper describes a new low power fully differential second-order continuous-time low pass filter for use at video frequencies. The filter uses a single active device in combination with MOSFET resistors and grounded capacitors to achieve very low power consumption, small chip area and large dynamic range. The ideal integrator is realised using an internally compensated opamp consisting of only current mirrors and voltage buffers, whilst the lossy integrator is implemented by a single passive RC circuit. The filter has been simulated using a CMOS process. Results show that with a single 5 V power supply, cut-off frequency can be tuned from 3.5 MHz to 8 MHz, dynamic range is better than 67 dB, and power consumption is less than 1.7 mW