A Classification of Single-Phase Transformerless Inverter Topologies for Photovoltaic Applications

© 2018 IEEE. In Photovoltaic (PV) applications, a transformer is often used to provide galvanic isolation and voltage ratio transformations. However, a transformer based inverter is bulky and has high conduction losses, therefore lead to a reduction in the inverter efficiency. To overcome this issue, the transformerless inverter topologies are addressed widely, but the main challenge of a transformerless inverter is common mode issue. Numerous topological modifications with their control and modulation techniques makes them difficult to follow, generalize and highlight the advantages and disadvantages. To address the issue, this paper gives an overview on transformerless inverter and classify them into subsection to discuss the merit and demerit of some of the major topologies. Five subsections based on common mode behavior, voltage clamping and decoupling techniques have been demonstrated (i.e., common ground, mid-point clamping, AC-decoupling, DC-decoupling and AC+DC decoupling). To verify the finding and for general consensus, major transformerless topologies are simulated using PLECS. A general summary is presented at the end to stimulate readers to acknowledge the problems and identify solutions

Transformerless Inverter Topologies for Single-Phase Photovoltaic Systems:A Comparative Review

In photovoltaic (PV) applications, a transformer is often used to provide galvanic isolation and voltage ratio transformations between input and output. However, these conventional iron-and copper-based transformers increase the weight/size and cost of the inverter while reducing the efficiency and power density. It is therefore desirable to avoid using transformers in the inverter. However, additional care must be taken to avoid safety hazards such as ground fault currents and leakage currents, e.g., via the parasitic capacitor between the PV panel and ground. Consequently, the grid connected transformerless PV inverters must comply with strict safety standards such as IEEE 1547.1, VDE0126-1-1, EN 50106, IEC61727, and AS/N ZS 5033. Various transformerless inverters have been proposed recently to eliminate the leakage current using different techniques such as decoupling the dc from the ac side and/or clamping the common mode (CM) voltage (CMV) during the freewheeling period, or using common ground configurations. The permutations and combinations of various decoupling techniques with integrated voltage buck-boost for maximum power point tracking (MPPT) allow numerous new topologies and configurations which are often confusing and difficult to follow when seeking to select the right topology. Therefore, to present a clear picture on the development of transformerless inverters for the next-generation grid-connected PV systems, this paper aims to comprehensively review and classify various transformerless inverters with detailed analytical comparisons. To reinforce the findings and comparisons as well as to give more insight on the CM characteristics and leakage current, computer simulations of major transformerless inverter topologies have been performed in PLECS software. Moreover, the cost and size are analyzed properly and summarized in a table. Finally, efficiency and thermal analysis are provided with a general summary as well as a technology roadmap.</p

Design and Evaluation of High Efficiency Power Converters Using Wide-Bandgap Devices for PV Systems

The shortage of fossil resources and the need for power generation options that produce little or no environmental pollution drives and motivates the research on renewable energy resources. Power electronics play an important role in maximizing the utilization of energy generation from renewable energy resources. One major renewable energy source is photovoltaics (PV), which comprises half of all recently installed renewable power generation in the world. For a grid-connected system, two power stages are needed to utilize the power generated from the PV source. In the first stage, a DCDC converter is used to extract the maximum power from the PV panel and to boost the low output voltage generated to satisfy the inverter side requirements. In the second stage, a DC-AC inverter is used to convert and deliver power loads for grid-tied applications. In general, PV panels have low efficiency so high-performance power converters are required to ensure highly efficient PV systems. The development of wide-bandgap (WBG) power switching devices, especially in the range of 650 V and 1200 V blocking class voltage, opens up the possibility of achieving a reliable and highly efficient grid-tied PV system. This work will study the benefits of utilizing WBG semiconductor switching devices in low power residential scale PV systems in terms of efficiency, power density, and thermal analysis. The first part of this dissertation will examine the design of a high gain DC-DC converter. Also, a performance comparison will be conducted between the SiC and Si MOSFET switching devices at 650 V blocking voltage regarding switching waveform behavior, switching and conduction losses, and high switching frequency operation. A major challenge in designing a transformerless inverter is the circulating of common mode leakage current in the absence of galvanic isolation. The value of the leakage current must be less than 300mA, per the DIN VDE 0126-1-1 standard. The second part of this work investigates a proposed high-efficiency transformerless inverter with low leakage current. Subsequently, the benefits of using SiC MOSFET are evaluated and compared to Si IGBT at 1200 V blocking voltage in terms of efficiency improvement, filter size reduction, and increasing power rating. Moreover, a comprehensive thermal model design is presented using COMSOL software to compare the heat sink requirements of both of the selected switching devices, SiC MOSFET and Si IGBT. The benchmarking of switching devices shows that SiC MOSFET has superior switching and conduction characteristics that lead to small power losses. Also, increasing switching frequency has a small effect on switching losses with SiC MOSFET due to its excellent switching characteristics. Therefore, system performance is found to be enhanced with SiC MOSFET compared to that of Si MOSFET and Si IGBET under wide output loads and switching frequency situations. Due to the high penetration of PV inverters, it is necessary to provide advanced functions, such as reactive power generation to enable connectivity to the utility grid. Therefore, this research proposes a modified modulation method to support the generation of reactive power. Additionally, a modified topology is proposed to eliminate leakage current

Transformerless Microinverter with Low Leakage Current Circulation and Low Input Capacitance Requirement for PV Applications

The inevitable depletion of limited fossil fuels combined with their harmful footprint on the environment led to a global pursuit for alternative energy sources that are clean and inexhaustible. Renewable energies such as wind, biomass and solar are the best alternative energy candidates, with the latter being more suitable for GCC countries. Besides, the energy generated from photovoltaic (PV) modules is one of the elegant examples of harnessing solar energy, as it is clean, pollutant-free and modular. Furthermore, recent advances in PV technology, especially grid-connected PV systems revealed the preeminence of using multiple small inverters called (Microinverters) over using the conventional single inverter configuration. Specifically, the break-even cost point can be reached faster and the system modularity increases with microinverters usage. Nonetheless, due to microinverter’s small ratings designers prefer transformerless designs because transformer removal achieves higher efficiency and power density. However, the transformer removal results in loss of galvanic isolation that leads to dangerous leakage current circulation that affects system safety. Another issue with microinverters is that since they are installed outside their bulky DC-Link electrolytic capacitor lifetime deteriorates the system reliability because electrolytic capacitor failure rate increases as temperature increases. Moreover, the DC-Link capacitor is used to decouple the 2nd order power harmonic ripples that appear in single-phase systems. Thus, the objective of this thesis is to design an efficient transformerless microinverter that has low leakage current circulation and low input capacitance requirement with a minimum number of active switches. In other words, the objective is to increase the safety and the reliability of the system while maintaining the high efficiency. Eventually, the configuration selected is the transformerless differential buck microinverter with LCL filter and it is modeled with passive resonance damping and active resonance damping control

Novel High Efficiency H-Bridge Transformerless Inverter for Grid-Connected Single-Phase Photovoltaic Systems

© 2018 IEEE. This paper proposes a new H-bridge type transformerless inverter for grid-connected photovoltaic (PV) application. The proposed H-bridge zero voltage switch controlled rectifier (HB-ZVSCR) inverter uses additional switches and diodes at the AC side with voltage clamping feature to the DC midpoint. Main characteristics of the proposed inverter are the high conversion efficiency and low leakage current, which make it a suitable candidate for grid-connected PV applications. The analysis and operating principles of the proposed inverter are discussed in details. This theoretical findings has been simulated using PLECS software to verify the common mode voltage (CMV) and leakage current behaviors and the results are compared with similar existing midpoint voltage clamping inverter topologies (i.e. HB-ZVR and HB-ZVR-D). Furthermore, power loss and efficiency of the proposed inverter have been evaluated and compared with existing topologies

Analysis and Design of Solar Photo voltaic Grid Connected Inverter

This paper presents common mode voltage analysis of single phase grid connected photovoltaic inverter. Many researchers proposed different grid tie inverters for applications like domestic powering, street lighting, water pumping, cooling and heating applications, however traditional grid tie PV inverter uses either a line frequency or a high frequency transformer between the inverter and grid but losses will increase in the network leading to reduced efficiency of the system. In order to increase the efficiency, with reduced size and cost of the system, the effective solution is to remove the isolation transformer. But common mode (CM) ground leakage current due to parasitic capacitance between the PV panels and the ground making the system unreliable. The common mode current reduces the efficiency of power conversion stage, affects the quality of grid current, deteriorate the electric magnetic compatibility and give rise to the safety threats. In order to eliminate the common mode leakage current in Transformerless PV systm two control algorithms of multi-carrier pwm are implemented and compared for performance analysis.The shoot-through issue that is encountered by traditional voltage source inverter is analyzed for enhanced system reliability. These control algorithms are compared for common mode voltage and THD comparisons. The proposed system is designed using MATLAB/SIMULINK software for analysis

H-Bridge Zero-Voltage Switch Controlled Rectifier (HB-ZVSCR) Transformerless Mid-Point-Clamped Inverter for Photovoltaic Applications

A single-phase transformerless mid-point clamped H-bridge zero-voltage switch-controlled rectifier inverter topology is proposed in this paper for photovoltaic (PV) systems to address the issue of common mode (CM) voltage and leakage currents. Apart from the full H-bridge inverter, the proposed voltage clamping circuit consists of two switches and a full-bridge diode which clamps the AC terminal to the DC midpoint (consisting of two DC-link capacitors) during the freewheeling period. As a result, the common mode voltage is held constant which makes it suitable for the grid-connected PV system. The operating principle and CM effect of the proposed topology are analysed and compared with the conventional topologies. This is followed by the thermal analysis and loss calculation, which shows that the proposed circuit is more efficient over the conventional topologies. Validation is carried out using MATLAB-Simulink using the PLECS toolbox followed by a scale down prototype of 1.5 kW. It is shown that the proposed inverter has the 98±1% efficiency over a wide range of loads with a peak efficiency of 98.96%, and the total harmonic distortion of the output current relatively low (≤1.8 %). The leakage current (icm) is measured for different values of parasitic capacitance that reaches a maximum of 16.65 mA for 330 nF capacitor under consideration which is well below the limit set by different safety standard

Analysis and Design of Single-Phase Transformerless Inverter for Photovoltaic Applications

University of Technology Sydney. Faculty of Engineering and Information Technology.This thesis provides a comprehensive analysis of different transformerless inverter topologies (TLIs) and their control and modulation techniques. Considering the challenges and merits of the transformerless inverter, four different types of transformerless inverter topologies for PV applications have been investigated, analysed and designed in this thesis. The first topology is H-bridge Zero Voltage Switch Controlled Rectifier (HB-ZVSCR) transformerless mid-point-clamped inverter. The operating principle and CM effect of the proposed topology are analysed and compared with the conventional topologies. This is followed by the thermal analysis and loss calculation which shows better efficiency over the conventional topologies. Validation is carried out using MATLAB-Simulink using the PLECS toolbox followed by a scale-down prototype of 1.5 kW. The second topology is a single-phase switched-capacitor (SC) based (2n+1)-level inverter with reduced number of components and input DC voltage supply magnitude. The total number of output voltage levels can reach up to (2n+ 1) levels, where n ≥ 2 is the number of switching cells consisting of three power switches and two switched-capacitors. The operating principle is presented in detail followed by comparative analysis, thermal modelling and design guidelines. Finally, measurement results are carried out for a 5-level inverter with two SC cells as an example to verify the performance of the proposed (2n+1)-level inverter over different operating conditions. The third topology is a novel dual-mode five-level common grounded type (5L-DM-CGT) transformerless inverter topology for a medium-power application with a wide input voltage range (200 V – 400 V). The theoretical analysis shows the advantages of the dual-mode inverter for various industrial applications. Finally, the laboratory test results are presented to verify the theoretical analysis. The final topology is a novel configuration of switched capacitor multilevel inverters (SCMLIs) with a lower number of power components with inherent voltage boost. The proposed topology is compared with other existing five-level inverter topologies to show its superior capabilities/advantages. The performance of the proposed topology is validated by OPAL-RT. Overall, this thesis provides a comprehensive analysis of all transformerless inverter topologies and their control and modulation techniques and come up with the concept of new single-phase transformerless inverter topologies. The new topologies utilizes minimal components with low voltage stress and offers high power quality output with low total harmonic distortion (THD), high efficiency and power density, low cost and size, and simple modulation techniques

New Topologies and Advanced Control of Power Electronic Converters for Renewable Energy based Microgrids

Solar energy-based microgrids are increasingly promising due to their many features, such as being environmentally friendly and having low operating costs. Power electronic converters, filters, and transformers are the key components to integrate the solar photovoltaic (PV) systems with the microgrids. The power electronic converters play an important role to reduce the size of the filter circuit and eliminate the use of the bulky and heavy traditional power frequency step-up transformer. These power converters also play a vital role to integrate the energy storage systems such as batteries and the superconducting magnetic energy storage (SMES) unit in a solar PV power-based microgrid. However, the performance of these power converters depends upon the switching technique and the power converter configuration. The switching techniques can improve the power quality, i.e. lower total harmonic distortion at the converter output waveform, reduce the converter power loss, and can effectively utilize the dc bus voltage, which helps to improve the power conversion efficiency of the power electronic converter. The power converter configuration can reduce the size of the power converter and make the power conversion system more efficient. In addition to the advanced switching technique, a supervisory control can also be integrated with these power converters to ensure the optimal power flow within the microgrid. First, this thesis reviews different existing power converter topologies with their switching techniques and control strategies for the grid integration of solar PV systems. To eliminate the use of the bulky and heavy line frequency step-up transformer to integrate solar PV systems to medium voltage grids, the high frequency magnetic linkbased medium voltage power converter topologies are discussed and compared based on their performance parameters. Moreover, switching and conduction losses are calculated to compare the performance of the switching techniques for the magnetic-linked power converter topologies. In this thesis, a new pulse width modulation technique has been proposed to integrate the SMES system with the solar PV system-based microgrid. The pulse width modulation technique is designed to provide reactive power into the network in an effective way. The modulation technique ensures lower total harmonic distortion (THD), lower switching loss, and better utilization of dc-bus voltage. The simulation and experimental results show the effectiveness of the proposed pulse width modulation technique. In this thesis, an improved version of the previously proposed switching technique has been designed for a transformer-less PV inverter. The improved switching technique can ensure effective active power flow into the network. A new switching scheme has been proposed for reactive power control to avoid unnecessary switching faced by the traditional switching technique in a transformer-less PV inverter. The proposed switching technique is based on the peak point value of the grid current and ensures lower switching loss compared to other switching techniques. In this thesis, a new magnetic-linked multilevel inverter has been designed to overcome the issues faced by the two-level inverters and traditional multilevel inverters. The proposed multilevel inverter utilizes the same number of electronic switches but fewer capacitors compared to the traditional multilevel inverters. The proposed multilevel inverter solves the capacitor voltage balancing and utilizes 25% more of the dc bus voltage compared to the traditional multilevel inverter, which reduces the power rating of the dc power source components and also extends the input voltage operating range of the inverter. An improved version magnetic-linked multilevel inverter is proposed in this thesis with a model predictive control technique. This multilevel inverter reduces both the number of switches and capacitors compared to the traditional multilevel inverter. This multilevel inverter also solves the capacitor voltage balancing issue and utilizes 50% more of the dc bus voltage compared to the traditional multilevel inverter. Finally, an energy management system has been designed for the developed power converter and control to achieve energy resiliency and minimum operating cost of the microgrid. The model predictive control-based energy management system utilizes the predicted load data, PV insolation data from web service, electricity price data, and battery state of charge data to select the battery charging and discharging pattern over the day. This model predictive control-based supervisory control with the advanced power electronic converter and control makes the PV energy-based microgrid more efficient and reliable

H8 Inverter for Common-Mode Voltage Reduction in Electric Drives

This paper presents a modified two-level three-phase inverter for the reduction of the leakage current. With respect to a traditional two-level inverter, the proposed solution reduces the common-mode voltage (CMV), both in amplitude and frequency. Between the dc source and the traditional three-phase bridge, two active dc-decoupling devices and a voltage-clamping network have been added. A dedicated control strategy was developed adopting a modified space vector pulse-width modulation, oriented to the reduction of the CMV. Simulations showing the good performance of the solution are presented. A preliminary prototype was developed and experimental results are presented