Non-fragile H∞ control with randomly occurring gain variations, distributed delays and channel fadings

This study is concerned with the non-fragile H∞ control problem for a class of discrete-time systems subject to randomly occurring gain variations (ROGVs), channel fadings and infinite-distributed delays. A new stochastic phenomenon (ROGVs), which is governed by a sequence of random variables with a certain probabilistic distribution, is put forward to better reflect the reality of the randomly occurring fluctuation of controller gains implemented in networked environments. A modified stochastic Rice fading model is then exploited to account for both channel fadings and random time-delays in a unified representation. The channel coefficients are a set of mutually independent random variables which abide by any (not necessarily Gaussian) probability density function on [0, 1]. Attention is focused on the analysis and design of a non-fragile H∞ outputfeedback controller such that the closed-loop control system is stochastically stable with a prescribed H∞ performance. Through intensive stochastic analysis, sufficient conditions are established for the desired stochastic stability and H∞ disturbance attenuation, and the addressed non-fragile control problem is then recast as a convex optimisation problem solvable via the semidefinite programme method. An example is finally provided to demonstrate the effectiveness of the proposed design method

Fully automated urban traffic system

The replacement of the driver with an automatic system which could perform the functions of guiding and routing a vehicle with a human's capability of responding to changing traffic demands was discussed. The problem was divided into four technological areas; guidance, routing, computing, and communications. It was determined that the latter three areas being developed independent of any need for fully automated urban traffic. A guidance system that would meet system requirements was not being developed but was technically feasible

Variable Speed Limit Control at SAG Curves Through Connected Vehicles: Implications of Alternative Communications and Sensing Technologies

Connected vehicles (CVs) will enable new applications to improve traffic flow. This study’s focus is to investigate how potential implementation of variable speed limit (VSL) through different types of communication and sensing technologies on CVs may improve traffic flow at a sag curve. At sag curves, the gradient changes from negative to positive values which causes a reduction in the roadway capacity and congestion. A VSL algorithm is developed and implemented in a simulation environment for controlling the inflow of vehicles to a sag curve on a freeway to minimize delays and increase throughput. Both vehicle-to-vehicle (V2V) and infrastructure-to-vehicle (I2V) options for CVs are investigated while implementing the VSL control strategy in a simulation environment. Through a feedback control algorithm, the speed of CVs are manipulated in the upstream of the sag curve to avoid the formation of bottlenecks caused by the change in longitudinal driver behavior. A modified version of the intelligent driver model (IDM) is used to simulate driving behavior on the sag curve. Depending on the traffic density at a sag curve, the feedback control algorithm adjusts the approach speeds of CVs so that the throughput of the sag curve is maximized. A meta-heuristic algorithm is employed to determine the critical control parameters. Various market penetration rates for CVs are considered in the simulations for three alternative communications and sensing technologies. It is demonstrated that for higher Market Penetration Rates (MPR) the performance is the same for all three scenarios which means there is no need for infrastructure-based sensing when the MPR is high enough. The results demonstrate that not only the MPR of CVs but also how CVs are distributed in the traffic stream is critical for system performance. While MPR could be high, uneven distribution of CVs and lack of CVs at the critical time periods as congestion is building up may cause a deterioration in system performance

A Review of Traffic Signal Control.

The aim of this paper is to provide a starting point for the future research within the SERC sponsored project "Gating and Traffic Control: The Application of State Space Control Theory". It will provide an introduction to State Space Control Theory, State Space applications in transportation in general, an in-depth review of congestion control (specifically traffic signal control in congested situations), a review of theoretical works, a review of existing systems and will conclude with recommendations for the research to be undertaken within this project

Autonomous landing of fixed-wing aircraft on mobile platforms

E n esta tesis se propone un nuevo sistema que permite la operación de aeronaves autónomas sin tren de aterrizaje. El trabajo está motivado por el interés industrial en aeronaves con la capacidad de volar a gran altitud, con más capacidad de carga útil y capaces de aterrizar con viento cruzado. El enfoque seguido en este trabajo consiste en eliminar el sistema de aterrizaje de una aeronave de ala fija empleando una plataforma móvil de aterrizaje en tierra. La aeronave y la plataforma deben sincronizar su movimiento antes del aterrizaje, lo que se logra mediante la estimación del estado relativo entre ambas y el control cooperativo del movimiento. El objetivo principal de esta Tesis es el desarrollo de una solución práctica para el aterrizaje autónomo de una aeronave de ala fija en una plataforma móvil. En la tesis se combinan nuevos métodos con experimentos prácticos para los cuales se ha desarrollado un sistema de pruebas específico. Se desarrollan dos variantes diferentes del sistema de aterrizaje. El primero presta atención especial a la seguridad, es robusto ante retrasos en la comunicación entre vehículos y cumple procedimientos habituales de aterrizaje, al tiempo que reduce la complejidad del sistema. En el segundo se utilizan trayectorias optimizadas del vehículo y sincronización bilateral de posición para maximizar el rendimiento del aterrizaje en términos de requerimientos de longitud necesaria de pista, pero la estabilidad es dependiente del retraso de tiempo, con lo cual es necesario desarrollar un controlador estabilizador ampliado, basado en pasividad, que permite resolver este problema. Ambas estrategias imponen requisitos funcionales a los controladores de cada uno de los vehículos, lo que implica la capacidad de controlar el movimiento longitudinal sin afectar el control lateral o vertical, y viceversa. El control de vuelo basado en energía se utiliza para proporcionar dicha funcionalidad a la aeronave. Los sistemas de aterrizaje desarrollados se han analizado en simulación estableciéndose los límites de rendimiento mediante múltiples repeticiones aleatorias. Se llegó a la conclusión de que el controlador basado en seguridad proporciona un rendimiento de aterrizaje satisfactorio al tiempo que suministra una mayor seguridad operativa y un menor esfuerzo de implementación y certificación. El controlador basado en el rendimiento es prometedor para aplicaciones con una longitud de pista limitada. Se descubrió que los beneficios del controlador basado en el rendimiento son menos pronunciados para una dinámica de vehículos terrestres más lenta. Teniendo en cuenta la dinámica lenta de la configuración del demostrador, se eligió el enfoque basado en la seguridad para los primeros experimentos de aterrizaje. El sistema de aterrizaje se validó en diversas pruebas de aterrizaje exitosas, que, a juicio del autor, son las primeras en el mundo realizadas con aeronaves reales. En última instancia, el concepto propuesto ofrece importantes beneficios y constituye una estrategia prometedora para futuras soluciones de aterrizaje de aeronaves.In this thesis a new landing system is proposed, which allows for the operation of autonomous aircraft without landing gear. The work was motivated by the industrial need for more capable high altitude aircraft systems, which typically suffer from low payload capacity and high crosswind landing sensitivity. The approach followed in this work consists in removing the landing gear system from the aircraft and introducing a mobile ground-based landing platform. The vehicles must synchronize their motion prior to landing, which is achieved through relative state estimation and cooperative motion control. The development of a practical solution for the autonomous landing of an aircraft on a moving platform thus constitutes the main goal of this thesis. Therefore, theoretical investigations are combined with real experiments for which a special setup is developed and implemented. Two different landing system variants are developed — the safety-based landing system is robust to inter-vehicle communication delays and adheres to established landing procedures, while reducing system complexity. The performance-based landing system uses optimized vehicle trajectories and bilateral position synchronization to maximize landing performance in terms of used runway, but suffers from time delay-dependent stability. An extended passivity-based stabilizing controller was implemented to cope with this issue. Both strategies impose functional requirements on the individual vehicle controllers, which imply independent controllability of the translational degrees of freedom. Energy-based flight control is utilized to provide such functionality for the aircraft. The developed landing systems are analyzed in simulation and performance bounds are determined by means of repeated random sampling. The safety-based controller was found to provide satisfactory landing performance while providing higher operational safety, and lower implementation and certification effort. The performance-based controller is promising for applications with limited runway length. The performance benefits were found to be less pronounced for slower ground vehicle dynamics. Given the slow dynamics of the demonstrator setup, the safety-based approach was chosen for first landing experiments. The landing system was validated in a number of successful landing trials, which to the author’s best knowledge was the first time such technology was demonstrated on the given scale, worldwide. Ultimately, the proposed concept offers decisive benefits and constitutes a promising strategy for future aircraft landing solutions

Active suspension control of electric vehicle with in-wheel motors

In-wheel motor (IWM) technology has attracted increasing research interests in recent years due to the numerous advantages it offers. However, the direct attachment of IWMs to the wheels can result in an increase in the vehicle unsprung mass and a significant drop in the suspension ride comfort performance and road holding stability. Other issues such as motor bearing wear motor vibration, air-gap eccentricity and residual unbalanced radial force can adversely influence the motor vibration, passenger comfort and vehicle rollover stability. Active suspension and optimized passive suspension are possible methods deployed to improve the ride comfort and safety of electric vehicles equipped with inwheel motor. The trade-off between ride comfort and handling stability is a major challenge in active suspension design. This thesis investigates the development of novel active suspension systems for successful implementation of IWM technology in electric cars. Towards such aim, several active suspension methods based on robust H∞ control methods are developed to achieve enhanced suspension performance by overcoming the conflicting requirement between ride comfort, suspension deflection and road holding. A novel fault-tolerant H∞ controller based on friction compensation is in the presence of system parameter uncertainties, actuator faults, as well as actuator time delay and system friction is proposed. A friction observer-based Takagi-Sugeno (T-S) fuzzy H∞ controller is developed for active suspension with sprung mass variation and system friction. This method is validated experimentally on a quarter car test rig. The experimental results demonstrate the effectiveness of proposed control methods in improving vehicle ride performance and road holding capability under different road profiles. Quarter car suspension model with suspended shaft-less direct-drive motors has the potential to improve the road holding capability and ride performance. Based on the quarter car suspension with dynamic vibration absorber (DVA) model, a multi-objective parameter optimization for active suspension of IWM mounted electric vehicle based on genetic algorithm (GA) is proposed to suppress the sprung mass vibration, motor vibration, motor bearing wear as well as improving ride comfort, suspension deflection and road holding stability. Then a fault-tolerant fuzzy H∞ control design approach for active suspension of IWM driven electric vehicles in the presence of sprung mass variation, actuator faults and control input constraints is proposed. The T-S fuzzy suspension model is used to cope with the possible sprung mass variation. The output feedback control problem for active suspension system of IWM driven electric vehicles with actuator faults and time delay is further investigated. The suspended motor parameters and vehicle suspension parameters are optimized based on the particle swarm optimization. A robust output feedback H∞ controller is designed to guarantee the system’s asymptotic stability and simultaneously satisfying the performance constraints. The proposed output feedback controller reveals much better performance than previous work when different actuator thrust losses and time delay occurs. The road surface roughness is coupled with in-wheel switched reluctance motor air-gap eccentricity and the unbalanced residual vertical force. Coupling effects between road excitation and in wheel switched reluctance motor (SRM) on electric vehicle ride comfort are also analysed in this thesis. A hybrid control method including output feedback controller and SRM controller are designed to suppress SRM vibration and to prolong the SRM lifespan, while at the same time improving vehicle ride comfort. Then a state feedback H∞ controller combined with SRM controller is designed for in-wheel SRM driven electric vehicle with DVA structure to enhance vehicle and SRM performance. Simulation results demonstrate the effectiveness of DVA structure based active suspension system with proposed control method its ability to significantly improve the road holding capability and ride performance, as well as motor performance

The Hierarchical Control Method for Coordinating a Group of Connected Vehicles on Urban Roads

Safety, mobility and environmental impact are the three major challenges in today\u27s transportation system. As the advances in wireless communication and vehicle automation technologies, they have rapidly led to the emergence and development of connected and automated vehicles (CAVs). We can expect fully CAVs by 2030. The CAV technologies offer another solution for the issues we are dealing with in the current transportation system. In the meanwhile, urban roads are one of the most important part in the transportation network. Urban roads are characterized by multiple interconnected intersections. They are more complicated than highway traffic, because the vehicles on the urban roads are moving in multiple directions with higher relative velocity. Most of the traffic accidents happened at intersections and the intersections are the major contribution to the traffic congestions. Our urban road infrastructures are also becoming more intelligent. Sensor-embedded roadways are continuously gathering traffic data from passing vehicles. Our smart vehicles are meeting intelligent roads. However, we have not taken the fully advantages of the data rich traffic environment provided by the connected vehicle technologies and intelligent road infrastructures. The objective of this research is to develop a coordination control strategy for a group of connected vehicles under intelligent traffic environment, which can guide the vehicles passing through the intersections and make smart lane change decisions with the objective of improving overall fuel economy and traffic mobility. The coordination control strategy should also be robust to imperfect connectivity conditions with various connected vehicle penetration rate. This dissertation proposes a hierarchical control method to coordinate a group of connected vehicles travelling on urban roads with intersections. The dissertation includes four parts of the application of our proposed method: First, we focus on the coordination of the connected vehicles on the multiple interconnected unsignalized intersection roads, where the traffic signals are removed and the collision avoidance at the intersection area relays on the communication and cooperation of the connected vehicles and intersection controllers. Second, a fuel efficient hierarchical control method is proposed to control the connected vehicles travel on the signalized intersection roads. With the signal phase and timing (SPAT) information, our proposed approach is able to help the connected vehicles minimize red light idling and improve the fuel economy at the same time. Third, the research is extended form single lane to multiple lane, where the connected vehicle discretionary and cooperative mandatory lane change have been explored. Finally, we have analysis the real-world implementation potential of our proposed algorithm including the communication delay and real-time implementation analysis

An Analysis of the Spatio-Temporal Factors Affecting Aircraft Conflicts Based on Simulation Modelling

The demand for air travel worldwide continues to grow at a rapid rate, especially in Europe and the United States. In Europe, the demand exceeded predictions with a real annual growth of 7.1% in the period 1985-1990, against a prediction of 2.4%. By the year 2010, the demand is expected to double from the 1990 level. Within the UK international scheduled passenger traffic is predicted to increase, on average, by 5.8 per cent per year between 1999 and 2003. The demand has not been matched by availability of capacity. In Western Europe many of the largest airports suffer from runway capacity constraints. Europe also suffers from an en-route airspace capacity constraint, which is determined by the workload of the air traffic controllers, i.e. the physical and mental work that controllers must undertake to safely conduct air traffic under their jurisdiction through en-route airspace. The annual cost to Europe due to air traffic inefficiency and congestion in en-route airspace is estimated to be 5 billion US Dollars, primarily due to delays caused by non-optimal route structures and reduced productivity of controllers due to equipment inefficiencies. Therefore, to in order to decrease the total delay, an increase in en-route capacity is of paramount importance. At a global scale and in the early 1980s, the International Civil Aviation Organisation (ICAO) recognised that the traditional air traffic control (ATC) systems would not cope with the growth in demand for capacity. Consequently new technologies and procedures have been proposed to enable ATC to cope with this demand, e.g. satellite-based system concept to meet the future civil aviation requirements for communication, navigation and surveillance/ air traffic management (CNS/ATM). In Europe, the organisation EUROCONTROL (established in 1960 to co-ordinate European ATM) proposed a variety of measures to increase the capacity of en-route airspace. A key change envisaged is the increasing delegation of responsibilities for control to flight crew, by the use of airborne separation assurance between aircraft, leading eventually to ?free flight? airspace. However, there are major concerns regarding the safety of operations in ?free flight? airspace. The safety of such airspace can be investigated by analysing the factors that affect conflict occurrence, i.e. a loss of the prescribed separation between two aircraft in airspace. This paper analyses the factors affecting conflict occurrence in current airspace and future free flight airspace by using a simulation model of air traffic controller workload, the RAMS model. The paper begins with a literature review of the factors that affect conflict occurrence. This is followed by a description of the RAMS model and of its use in this analysis. The airspace simulated is the Mediterranean Free Flight region, and the major attributes of this region and of the traffic demand patterns are outlined next. In particular a day?s air traffic is simulated in the two airspace scenarios, and rules for conflict detection and resolution are carefully defined. The following section outlines the framework for analysing the output from the simulations, using negative binomial (NB) and generalised negative binomial (GNB) regression, and discusses the estimation methods required. The next section presents the results of the regression analysis, taking into account the spatio-temporal nature of the data. The following section presents an analysis of the spatial and temporal pattern of conflicts in the two airspace scenarios across a day, highlighting possible metrics to indicate this. The paper concludes with future research directions based upon this analysis.

A Rule Based Control Algorithm for on-Ramp Merge With Connected and Automated Vehicles

One of the designs for future highways with the flow of Connected Automated Vehicles (CAVs) cars will be a dedicated lane for the CAVs to form platoons and travel with higher speeds and lower headways. The connectivity will enable the formation of platoons of CAVs traveling beside non-platoon lanes. The advent of connectivity between vehicles and the infrastructure will enable advanced control strategies ̶ improving the performance of the traffic ̶ to be incorporated in the traffic system. The merge area in a multilane highway with CAVs is one of the sections which can be enhanced by the operation of a control system. In this research, a model is developed for investigating the effects of a Rule Based control strategy yielding a more efficient and systematic method for the vehicles joining the highway mainlines comprised of platoon and non-platoon lanes. The actions tested for assisting the merge process included deceleration in the mainlines and lane change to join a platoon in the platoon lane. The model directs every CAV entering a multi-lane highway from an on-ramp, to the rightmost lane of the highway based on the appropriate action which is selected according to the traffic demand conditions and location of the on-ramp vehicle. To account for car following behavior, the vehicles in the platoon lanes are assumed to have a simplified CACC (cooperative adaptive cruise control) and those in the non-platoon lanes the IDM+ car-following model. The IDM+ car following model is modified with additional controls to incorporate the current technologies of Advanced Driver Assistant Systems (ADAS). The results of this study showed that the proposed car following model can increase the throughput of the non-platoon lane from approximately 2000 vehicle per hour (vph) to 3400 vph while the platoon lanes each had an average throughput of 3500 vph. The merge model enabled higher merging throughput for the merge area compared to current day conditions and displayed the potential for improved traffic performance in a connected environment comprised of platoon and non-platoon lanes. The results of this research will help in the design and development of advanced systems for controlling on-ramp merge sections in the future with CAVs