A novel scan segmentation design method for avoiding shift timing failure in scan testing

ITC : 2011 IEEE International Test Conference , 20-22 Sep. 2011 , Anaheim, CA, USAHigh power consumption in scan testing can cause undue yield loss which has increasingly become a serious problem for deep-submicron VLSI circuits. Growing evidence attributes this problem to shift timing failures, which are primarily caused by excessive switching activity in the proximities of clock paths that tends to introduce severe clock skew due to IR-drop-induced delay increase. This paper is the first of its kind to address this critical issue with a novel layout-aware scheme based on scan segmentation design, called LCTI-SS (Low-Clock-Tree-Impact Scan Segmentation). An optimal combination of scan segments is identified for simultaneous clocking so that the switching activity in the proximities of clock trees is reduced while maintaining the average power reduction effect on conventional scan segmentation. Experimental results on benchmark and industrial circuits have demonstrated the advantage of the LCTI-SS scheme

A Hardware Security Solution against Scan-Based Attacks

Scan based Design for Test (DfT) schemes have been widely used to achieve high fault coverage for integrated circuits. The scan technique provides full access to the internal nodes of the device-under-test to control them or observe their response to input test vectors. While such comprehensive access is highly desirable for testing, it is not acceptable for secure chips as it is subject to exploitation by various attacks. In this work, new methods are presented to protect the security of critical information against scan-based attacks. In the proposed methods, access to the circuit containing secret information via the scan chain has been severely limited in order to reduce the risk of a security breach. To ensure the testability of the circuit, a built-in self-test which utilizes an LFSR as the test pattern generator (TPG) is proposed. The proposed schemes can be used as a countermeasure against side channel attacks with a low area overhead as compared to the existing solutions in literature

A Scan-Out Power Reduction Method for Multi-Cycle BIST

High test power in logic BIST is a serious problem not only for production test, but also for board test, system debug or field test. Many low power BIST approaches that focus on scan-shift power or capture power have been proposed. However, it is known that a half of scan-shift power is compensated by test responses, which is difficult to control in those approaches. This paper proposes a novel approach that directly reduces scan-out power by modifying some flip-flops\u27 values in scan chains at the last capture. Experimental results show that the proposed method reduces scan-out power up to 30% with little loss of test coverage.2012 IEEE 21st Asian Test Symposium, 19-22 Nov. 2012, Niigata, Japa

A Flexible Power Control Method for Right Power Testing of Scan-Based Logic BIST

High power dissipation during scan-based logic BIST is a crucial problem that leads to over-testing. Although controlling test power of a circuit under test (CUT) to an appropriate level is strongly required, it is not easy to control test power in BIST. This paper proposes a novel power controlling method to control the toggle rate of the patterns to an arbitrary level by modifying pseudo random patterns generated by a TPG (Test Pattern Generator) of logic BIST. While many approaches have been proposed to control the toggle rate of the patterns, the proposed approach can provide higher fault coverage. Experimental results show that the proposed approach can control toggle rates to a predetermined target level and modified patterns can achieve high fault coverage without increasing test time.2016 IEEE 25th Asian Test Symposium (ATS), 21-24 Nov. 2016, Hiroshima, Japa

Power-Aware Testing For Low-Power VLSI Circuits

Low-power VLSI circuits are indispensable for almost all types of modern electronic devices, from battery-driven mobile gadgets to harvested-energy-driven wireless sensor systems. However, the testing of such low-power VLSI circuits has become a big challenge, especially due to the excessive power dissipation during scan testing. This paper will highlight three major test-power-induced problems (namely heat, false failures, clock stretch) and describe how to mitigate them with power-aware VLSI testing. Future research topics in this field will also be discussed.13th IEEE International Conference on Solid-State and Integrated Circuit Technology (ICSICT-2016), 25-28 October 2016, Hangzhou, Chin

Embedding deterministic patterns in partial pseudo-exhaustive test

The topic of this thesis is related to testing of very large scale integration circuits. The thesis presents the idea of optimizing mixed-mode built-in self-test (BIST) scheme. Mixed-mode BIST consists of two phases. The first phase is pseudo-random testing or partial pseudo-exhaustive testing (P-PET). For the faults not detected by the first phase, deterministic test patterns are generated and applied in the second phase. Hence, the defect coverage of the first phase influences the number of patterns to be generated and stored. The advantages of P-PET in comparison with usual pseudo-random test are in obtaining higher fault coverage and reducing the number of deterministic patterns in the second phase of mixed-mode BIST. Test pattern generation for P-PET is achieved by selecting characteristic polynomials of multiple-polynomial linear feedback shift register (MP-LFSR). In this thesis, the mixed-mode BIST scheme with P-PET in the first phase is further improved in terms of the fault coverage of the first phase. This is achieved by optimization of polynomial selection of P-PET. In usual mixed-mode BIST, the set of undetected by the first phase faults is handled in the second phase by generating deterministic test patterns for them. The method in the thesis is based on consideration of these patterns during polynomial selection. In other words, we are embedding deterministic test patterns in P-PET. In order to solve the problem, the algorithm for the selection of characteristic polynomials covering the pre-generated patterns is developed. The advantages of the proposed approach in terms of the defect coverage and the number of faults left after the first phase are presented using contemporary industrial circuits. A comparison with usual pseudo-random testing is also performed. The results prove the benefits of P-PET with embedded test patterns in terms of the fault coverage, while maintaining comparable test length and time

REDUCING POWER DURING MANUFACTURING TEST USING DIFFERENT ARCHITECTURES

Power during manufacturing test can be several times higher than power consumption in functional mode. Excessive power during test can cause IR drop, over-heating, and early aging of the chips. In this dissertation, three different architectures have been introduced to reduce test power in general cases as well as in certain scenarios, including field test. In the first architecture, scan chains are divided into several segments. Every segment needs a control bit to enable capture in a segment when new faults are detectable on that segment for that pattern. Otherwise, the segment should be disabled to reduce capture power. We group the control bits together into one or more control chains. To address the extra pin(s) required to shift data into the control chain(s) and significant post processing in the first architecture, we explored a second architecture. The second architecture stitches the control bits into the chains they control as EECBs (embedded enable capture bits) in between the segments. This allows an ATPG software tool to automatically generate the appropriate EECB values for each pattern to maintain the fault coverage. This also works in the presence of an on-chip decompressor. The last architecture focuses primarily on the self-test of a device in a 3D stacked IC when an existing FPGA in the stack can be programmed as a tester. We show that the energy expended during test is significantly less than would be required using low power patterns fed by an on-chip decompressor for the same very short scan chains

A Novel Scan Segmentation Design Method for Avoiding Shift Timing Failure in Scan Testing

High power consumption in scan testing can cause undue yield loss which has increasingly become a serious problem for deep-submicron VLSI circuits. Growing evidence attributes this problem to shift timing failures, which are primarily caused by excessive switching activity in the proximities of clock paths that tends to introduce severe clock skew due to IR-drop-induced delay increase. This paper is the first of its kind to address this critical issue with a novel layout-aware scheme based on scan segmentation design, called LCTI-SS (Low-Clock-Tree-Impact Scan Segmentation). An optimal combination of scan segments is identified for simultaneous clocking so that the switching activity in the proximities of clock trees is reduced while maintaining the average power reduction effect on conventional scan segmentation. Experimental results on benchmark and industrial circuits have demonstrated the advantage of the LCTI-SS scheme.2011 IEEE International Test Conference, 20-22 September 2011, Anaheim, CA, US

Low Power BIST for Scan-Shift and Capture Power

Low-power test technology has been investigated deeply to achieve an accurate and efficient testing. Although many sophisticated methods are proposed for scan-test, there are not so many for logic BIST because of its uncontrollable randomness. However, logic BIST currently becomes vital for system debug or field test. This paper proposes a novel low power BIST technology that reduces shift-power by eliminating the specified high-frequency parts of vectors and also reduces capture power. The authors show that the proposed technology not only reduces test power but also keeps test coverage with little loss.2012 IEEE 21st Asian Test Symposium, 19-22 Nov. 2012, Niigata, Japa

Test Strategies for Low Power Devices

Ultra low-power devices are being developed for embedded applications in bio-medical electronics, wireless sensor networks, environment monitoring and protection, etc. The testing of these low-cost, low-power devices is a daunting task. Depending on the target application, there are stringent guidelines on the number of defective parts per million shipped devices. At the same time, since such devices are cost-sensitive, test cost is a major consideration. Since system-level power-management techniques are employed in these devices, test generation must be power-management-aware to avoid stressing the power distribution infrastructure in the test mode. Structural test techniques such as scan test, with or without compression, can result in excessive heat dissipation during testing and damage the package. False failures may result due to the electrical and thermal stressing of the device in the test mode of operation, leading to yield loss. This paper considers different aspects of testing low-power devices and some new techniques to address these problems.Design, Automation and Test in Europe (DATE \u2708), 10-14 March 2008, Munich, German