61 research outputs found
EDA Solutions for Double Patterning Lithography
Expanding the optical lithography to 32-nm node and beyond is impossible using existing single exposure systems. As such, double patterning lithography (DPL) is the most promising option to generate the required lithography resolution, where the target layout is printed with two separate imaging processes. Among different DPL techniques litho-etch-litho-etch (LELE) and self-aligned double patterning (SADP) methods are the most popular ones, which apply two complete exposure lithography steps and an exposure lithography followed by a chemical imaging process, respectively.
To realize double patterning lithography, patterns located within a sub-resolution distance should be assigned to either of the imaging sub-processes, so-called layout decomposition. To achieve the optimal design yield, layout decomposition problem should be solved with respect to characteristics and limitations of the applied DPL method. For example, although patterns can be split between the two sub-masks in the LELE method to generate conflict free masks, this pattern split is not favorable due to its sensitivity to lithography imperfections such as the overlay error. On the other hand, pattern split is forbidden in SADP method because it results in non-resolvable gap failures in the final image. In addition to the functional yield, layout decomposition affects parametric yield of the designs printed by double patterning.
To deal with both functional and parametric challenges of DPL in dense and large layouts, EDA solutions for DPL are addressed in this thesis. To this end, we proposed a statistical method to determine the interconnect width and space for the LELE method under the effect of random overlay error. In addition to yield maximization and achieving near-optimal trade-off between different parametric requirements, the proposed method provides valuable insight about the trend of parametric and functional yields in future technology nodes.
Next, we focused on self-aligned double patterning and proposed layout design and decomposition methods to provide SADP-compatible layouts and litho-friendly decomposed layouts. Precisely, a grid-based ILP formulation of SADP decomposition was proposed to avoid decomposition conflicts and improve overall printability of layout patterns. To overcome the limited applicability of this ILP-based method to fully-decomposable layouts, a partitioning-based method is also proposed which is faster than the grid-based ILP decomposition method too. Moreover, an A∗-based SADP-aware detailed routing method was proposed which performs detailed routing and layout decomposition simultaneously to avoid litho-limited layout configurations. The proposed router preserves the uniformity of pattern density between the two sub-masks of the SADP process. We finally extended our decomposition method for double patterning to triple patterning and formulated SATP decomposition by integer linear programming. In addition to conventional minimum width and spacing constraints, the proposed decomposition method minimizes the mandrel-trim co-defined edges and maximizes the layout features printed by structural spacers to achieve the minimum pattern distortion.
This thesis is one of the very early researches that investigates the concept of litho-friendliness in SADP-aware layout design and decomposition. Provided by experimental results, the proposed methods advance prior state-of-the-art algorithms in various aspects. Precisely, the suggested SADP decomposition methods improve total length of sensitive trim edges, total EPE and overall printability of attempted designs. Additionally, our SADP-detailed routing method provides SADP-decomposable layouts in which trim patterns are highly robust to lithography imperfections. The experimental results for SATP decomposition show that total length of overlay-sensitive layout patterns, total EPE and overall printability of the attempted designs are also improved considerably by the proposed decomposition method. Additionally, the methods in this PhD thesis reveal several insights for the upcoming technology nodes which can be considered for improving the manufacturability of these nodes
Layout decomposition for triple patterning lithography
Nowadays the semiconductor industry is continuing to advance the limits of physics as the feature size of the chip keeps shrinking. Products of the 22 nm technology node are already available on the market, and there are many ongoing research studies for the 14/10 nm technology nodes and beyond. Due to the physical limitations, the traditional 193 nm immersion lithography is facing huge challenges in fabricating such tiny features. Several types of next-generation lithography techniques have been discussed for years, such as {\em extreme ultra-violet} (EUV) lithography, {\em E-beam direct write}, and {\em block copolymer directed self-assembly} (DSA). However, the source power for EUV is still an unresolved issue. The low throughput of E-beam makes it impractical for massive productions. DSA is still under calibration in research labs and is not ready for massive industrial deployment.
Traditionally features are fabricated under single litho exposure. As feature size becomes smaller and smaller, single exposure is no longer adequate in satisfying the quality requirements. {\em Double patterning lithography} (DPL) utilizes two litho exposures to manufacture features on the same layer. Features are assigned to two masks, with each mask going through a separate litho exposure. With one more mask, the effective pitch is doubled, thus greatly enhancing the printing resolution. Therefore, DPL has been widely recognized as a feasible lithography solution in the sub-22 nm technology node. However, as the technology continues to scale down to 14/10 nm and beyond, DPL begins to show its limitations as it introduces a high number of stitches, which increases the manufacturing cost and potentially leads to functional errors of the circuits. {\em Triple pattering lithography} (TPL) uses three masks to print the features on the same layer, which further enhances the printing resolution. It is a natural extension for DPL with three masks available, and it is one of the most promising solutions for the 14/10 nm technology node and beyond.
In this thesis, TPL decomposition for standard-cell-based designs is extensively studied. We proposed a polynomial time triple patterning decomposition algorithm which guarantees finding a TPL decomposition if one exists. For complex designs with stitch candidates, our algorithm is able to find a solution with the optimal number of stitches. For standard-cell-based designs, there are additional coloring constraints where the same type of cell should be fabricated following the same pattern. We proposed an algorithm that is guaranteed to find a solution when one exists. The framework of the algorithm is also extended to pattern-based TPL decompositions, where the cost of a decomposition can be minimized given a library of different patterns. The polynomial time TPL algorithm is further optimized in terms of runtime and memory while keeping the solution quality unaffected. We also studied the TPL aware detailed placement problem, where our approach is guaranteed to find a legal detailed placement satisfying TPL coloring constraints as well as minimizing the {\em half-perimeter wire length} (HPWL).
Finally, we studied the problem of performance variations due to mask misalignment in {\em multiple patterning decompositions} (MPL). For advanced technology nodes, process variations (mainly mask misalignment) have significant influences on the quality of fabricated circuits, and often lead to unexpected power/timing degenerations. Mask misalignment would complicate the way of simulating timing closure if engineers do not understand the underlying effects of mask misalignment, which only exists in multiple patterning decompositions. We mathematically proved the worst-case scenarios of coupling capacitance incurred by mask misalignment in MPL decompositions. A graph model is proposed which is guaranteed to compute the tight upper bound on the worst-case coupling capacitance of any MPL decompositions for a given layout
Design automation algorithms for advanced lithography
In circuit manufacturing, as the technology nodes keep shrinking, conventional 193 nm immersion lithography (193i) has reached its printability limit. To continue the scaling with Moore's law, different kinds of advanced lithography have been proposed, such as multiple patterning lithography (MPL), extreme ultraviolet (EUV), electron beam lithography (EBL) and directed self-assembly (DSA). While these new technologies create enormous opportunities, they also pose great design challenges due to their unique process characteristics and stringent constraints. In order to smoothly adopt these advanced lithography technologies in integrated circuit (IC) fabrication, effective electronic design automation (EDA) algorithms must be designed and integrated into computer-aided design (CAD) tools to address the underlying design constraints and help the circuit designer to better facilitate the lithography process. In this thesis, we focus on algorithmic design and efficient implementation of EDA algorithm for advanced lithography, including directed self-assembly (DSA) and self-aligned double patterning (SADP), to conquer the physical challenges and improve the manufacturing yield.
The first advanced lithography technology we explore is self-aligned double patterning (SADP). SADP has the significant advantage over traditional litho-etch-litho-etch (LELE) double patterning in its ability to eliminate overlay, making it a preferable DPL choice for the 14 nm technology node. As in any DPL technology, layout decomposition is the key problem. While the layout decomposition problem for LELE DPL has been well studied in the literature, only a few attempts have been made for the SADP layout decomposition problem. This thesis studies the SADP decomposition problem in different scenarios.
SADP has been successfully deployed in 1D patterns and has several applications; however, applying it to 2D patterns turns out to be much more difficult. All previous exact algorithms were based on computationally expensive methods such as SAT or ILP. Other previous algorithms were heuristics without a guarantee that an overlay-free solution can be found even if one exists. The SADP decomposition problem on general 2D layout is proven to be NP-complete. However, we show that if we restrict the overlay, the problem is polynomial-time solvable, and present an exact algorithm to determine if a given 2D layout has a no-overlay SADP decomposition.
When designing the layout decomposition algorithms, it is usually useful to take the layout structure into consideration. As most of the current IC layouts adopt a row-based standard cell design style, we can take advantage of its characteristics and design more efficient algorithms compared to the algorithms for general 2D patterns. In particular, the fixed widths of standard cells and power tracks on top and bottom of cells suggest that improvements can be made over the algorithms for general decomposition problem. We present a shortest-path based polynomial time SADP decomposition algorithm for row-based standard cell layout that efficiently finds decompositions with minimum overlay violations. Our proposed algorithm takes advantage of the fixed width of the cells and the alternating power tracks between the rows to limit the possible decompositions and thus achieve high efficiency.
The next advanced lithography technology we discuss in the thesis is directed self-assembly (DSA). Block copolymer directed self-assembly (DSA) is a promising technique for patterning contact holes and vias in 7 nm technology nodes. To pattern contacts/vias with DSA, guiding templates are usually printed first with conventional lithography (193i) that has a coarser pitch resolution. Contact holes are then patterned with DSA process. The guiding templates play the role of defining the DSA patterns, which have a finer resolution than the templates. As a result, different patterns can be obtained through controlling the templates. It is shown that DSA lithography is very promising in patterning contacts/vias in 7 nm technology node. However, to utilize DSA for full-chip manufacturing, EDA for DSA must be fully explored because EDA is the key enabler for manufacturing, and the EDA research for DSA is still lagging behind.
To pattern the contact layer with DSA, we must ensure that all the contacts in the layout require only feasible DSA templates. Nevertheless, the original layout may not be designed in a DSA-friendly way. However, even with an optimized library, infeasible templates may be introduced after the physical design phase. We propose a simulated-annealing (SA) based scheme to perform full-chip level contact layer optimization. According to the experimental results, the DSA conflicts in the contact layer are reduced by close to 90% on average after applying the proposed optimization algorithm.
It is a current trend that industry is transiting from the random 2D designs to highly regular 1D gridded designs for sub-20 nm nodes and fabricating circuit designs with print-cut technology. In this process, the randomly distributed cuts may be too dense to be printed by single patterning lithography. DSA has proven its success in contact hole patterning, and can be easily expanded to cut printing for 1D gridded designs. Nevertheless, the irregular distribution of cuts still presents a great challenge for DSA, as the self-assembly process usually forms regular patterns. As a result, the cut layer must be optimized for the DSA process. To address the above problem, we propose an efficient algorithm to optimize cut layers without hurting the original circuit logic. Our work utilizes a technique called `line-end extension' to move the cuts and extend the functional wires without changing the original functionality of the circuit. Consequently, the cuts can be redistributed and grouped into valid DSA templates.
Multiple patterning lithography has been widely adopted for today's circuit manufacturing. However, increasing the number of masks will make the manufacturing process more expensive. By incorporating DSA into the multiple patterning process, it is possible to reduce the number of masks and achieve a cost-effective solution. We study the decomposition problem for the contact layer in row-based standard cell layout with DSA-MP complementary lithography. We explore several heuristic-based approaches, and propose an algorithm that decomposes a standard cell row optimally in polynomial-time. Our experiments show that our algorithm is guaranteed to find a minimum cost solution if one exists, while the heuristic cannot or only finds a sub-optimal solution. Our results show that the DSA-MP complementary approach is very promising for the future advanced nodes.
As in any lithography technique, the process variation control and proximity correction are the most important issues. As the DSA templates are patterned by conventional lithography, the patterned templates are prone to deviate from mask shapes due to process variations, which will ultimately affect the contacts after the DSA process even for the same type of template. Therefore, in order to enable the DSA technology in contact/via layer printing, it is extremely important to accurately model and detect hotspots, as well as estimate the contact pitch and locations during the verification phase. We propose a machine learning based design automation framework for DSA verification. A novel DSA model and a set of features are included. We implemented the proposed ML-based flow and performed extensive experiments on comparing the performances of learning algorithms and features. The experimental results show that our approach is much more efficient than the traditional approach, and can produce highly accurate results
Recommended from our members
Standard cell optimization and physical design in advanced technology nodes
Integrated circuits (ICs) are at the heart of modern electronics, which rely heavily on the state-of-the-art semiconductor manufacturing technology. The key to pushing forward semiconductor technology is IC feature-size miniaturization. However, this brings ever-increasing design complexities and manufacturing challenges to the $340 billion semiconductor industry. The manufacturing of two-dimensional layout on high-density metal layers depends on complex design-for-manufacturing techniques and sophisticated empirical optimizations, which introduces huge amounts of turnaround time and yield loss in advanced technology nodes. Our study reveals that unidirectional layout design can significantly reduce the manufacturing complexities and improve the yield, which is becoming increasingly adopted in semiconductor industry [61, 89]. The lithography printing of unidirectional layout can be tightly controlled using advanced patterning techniques, such as self-aligned double and quadruple patterning. Despite the manufacturing benefits, unidirectional layout leads to more restrictive solution space and brings significant impacts on the IC design automation ow for routing closure. Notably, unidirectional routing limits the standard cell pin accessibility, which further exacerbates the resource competitions during routing. Moreover, for post-routing optimization, traditional redundant-via insertion has become obsolete under unidirectional routing style, which makes the yield enhancement task extremely challenging. Regardless of complex multiple patterning and design-for-manufacturing approaches, mask optimization through resolution enhancement techniques remains as the key strategy to improve the yield of the semiconductor manufacturing processes. Among them, Sub-Resolution Assist Feature (SRAF) generation is a very important method to improve lithographic process windows. Model-based SRAF generation has been widely used to achieve high accuracy but it is time-consuming and hard to obtain consistent SRAFs. This dissertation proposes novel CAD algorithms and methodologies for standard cell optimization and physical design in advanced technology nodes, which ultimately reduces the design cycle and manufacturing cost of IC design. First, a standard cell pin access optimization engine is proposed to evaluate the pin accessibility of a given standard cell library. We further propose novel pin access planning techniques and concurrent pin access optimizations to efficiently resolve the routing resource competitions, which generates much better routing solutions than state-of-the-art, manufacturing-friendly routers. To systematically improve the manufacturing yield in the post-routing stage, a global optimization engine has been introduced for redundant local-loop insertion considering advanced manufacturing constraints. Finally, we propose the first machine learning-based framework for fast yet consistent SRAF generation with the high quality of results.Electrical and Computer Engineerin
Recommended from our members
Lithography aware physical design and layout optimization for manufacturability
textAs technology continues to scale down, semiconductor manufacturing with 193nm lithography is greatly challenging because the required half pitch size is beyond the resolution limit. In order to bridge the gap between design requirements and manufacturing limitations, various resolution enhancement techniques have been proposed to avoid potentially problematic patterns and to improve product yield. In addition, co-optimization between design performance and manufacturability can further provide flexible and significant yield improvement, and it has become necessary for advanced technology nodes. This dissertation presents the methodologies to consider the lithography impact in different design stages to improve layout manufacturability. Double Patterning Lithography (DPL) has been a promising solution for sub-22nm node volume production. Among DPL techniques, self-aligned double patterning (SADP) provides good overlay controllability when two masks are not aligned perfectly. However, SADP process places several limitations on design flexibility and still exists many challenges in physical design stages. Starting from the early design stage, we analyze the standard cell designs and construct a set of SADP-aware cell placement candidates, and show that placement legalization based on this SADP awareness information can effectively resolve DPL conflicts. In the detailed routing stage, we propose a new routing cost formulation based on SADP-compliant routing guidelines, and achieve routing and layout decomposition simultaneously. In the case that limited routing perturbation is allowed, we propose a post-routing flow based on lithography simulation and lithography-aware design rules. Both routing methods, one in detailed routing stage and one in post routing stage, reduce DPL conflicts/violations significantly with negligible wire length impact. In the layout decomposition stage, layout modification is restricted and thus the manufacturability is even harder to guaranteed. By taking the advantage of complementary lithography, we present a new layout decomposition approach with e-beam cutting, which optimizes SADP overlay error and e-beam lithography throughput simultaneously. After the mask layout is defined, optical proximity correction (OPC) is one of the resolution enhancement techniques that is commonly required to compensate the image distortion from the lithography process. We propose an inverse lithography technique to solve the OPC problem considering design target and process window co-optimization. Our mask optimization is pixel based and thus can enable better contour fidelity. In the final physical verification stage, a complex and time-consuming lithography simulation needs to be performed to identify faulty patterns. We provide a classification method based on support vector machine and principle component analysis that detects lithographic hotspots efficiently and accurately.Electrical and Computer Engineerin
VLSI Routing for Advanced Technology
Routing is a major step in VLSI design, the design process of complex integrated circuits (commonly known as chips). The basic task in routing is to connect predetermined locations on a chip (pins) with wires which serve as electrical connections. One main challenge in routing for advanced chip technology is the increasing complexity of design rules which reflect manufacturing requirements. In this thesis we investigate various aspects of this challenge. First, we consider polygon decomposition problems in the context of VLSI design rules. We introduce different width notions for polygons which are important for width-dependent design rules in VLSI routing, and we present efficient algorithms for computing width-preserving decompositions of rectilinear polygons into rectangles. Such decompositions are used in routing to allow for fast design rule checking. A main contribution of this thesis is an O(n) time algorithm for computing a decomposition of a simple rectilinear polygon with n vertices into O(n) rectangles, preseverving two-dimensional width. Here the two-dimensional width at a point of the polygon is defined as the edge length of a largest square that contains the point and is contained in the polygon. In order to obtain these results we establish a connection between such decompositions and Voronoi diagrams. Furthermore, we consider implications of multiple patterning and other advanced design rules for VLSI routing. The main contribution in this context is the detailed description of a routing approach which is able to manage such advanced design rules. As a main algorithmic concept we use multi-label shortest paths where certain path properties (which model design rules) can be enforced by defining labels assigned to path vertices and allowing only certain label transitions. The described approach has been implemented in BonnRoute, a VLSI routing tool developed at the Research Institute for Discrete Mathematics, University of Bonn, in cooperation with IBM. We present experimental results confirming that a flow combining BonnRoute and an external cleanup step produces far superior results compared to an industry standard router. In particular, our proposed flow runs more than twice as fast, reduces the via count by more than 20%, the wiring length by more than 10%, and the number of remaining design rule errors by more than 60%. These results obtained by applying our multiple patterning approach to real-world chip instances provided by IBM are another main contribution of this thesis. We note that IBM uses our proposed combined BonnRoute flow as the default tool for signal routing
Design for Manufacturing in IC Fabrication: Mask Cost, Circuit Performance and Convergence
Ph.DDOCTOR OF PHILOSOPH
Novel patterning techniques for manufacturing organic and nanostructured electronics
Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Materials Science and Engineering, 2007.Page 206 blank.Includes bibliographical references.Molecular organic semiconductors and nanometer size particles are two new classes of functional materials allowing fabrication of electronic devices on low-cost and large area substrates. Patterning these electronic materials requires the development of unconventional techniques, and the scientific understanding behind the manufacture processes. We introduce the first-generation Molecular Jet (MoJet) printing technique for vacuum deposition of evaporated thin films and apply it to the fabrication of high-resolution pixelated (800 ppi) molecular organic light emitting devices (OLEDs) based on aluminum tris(8-hydroxyquinoline) (Alq3), and the fabrication of pentacene based organic field effect transistors (OFETs) with narrow channel (15 gm) and asymmetric silver/gold contacts. Patterned printing of both organic and metal films is demonstrated, with the operating properties of MoJet-printed OLEDs and OFETs shown to be comparable with the performance of devices fabricated by conventional evaporative deposition through a metal stencil. This MoJet printing technique is reconfigurable for digital fabrication of arbitrary patterns with multiple material sets and a high print accuracy of better than 5gtm, and scalable to large area substrates.(cont.) Analogous to the concept of "drop-on-demand" in Inkjet printing technology, MoJet printing is a "flux-on-demand" process and we show it capable of fabricating multi-layer stacked film structures, as needed for engineered organic devices. We present the concept and the applications of the second-generation MoJet printing technique. Using this technique, we demonstrate patterned molecular organic semiconducting thin films directly printed by a three-step local evaporative deposition, in conjunction with using the HP thermal InkJet printing technology. This MoJet printing technique can be applied to pattern solution-processable molecular organic thin films, providing flux-on-demand in an ambient environment. We develop an Inkjet assisted micro-contact printing technique for the patterning of colloidal semiconductor nanoparticles. Active OLEDs incorporated with a uniform thickness layer of colloidal nanoparticles are fabricated by using this Inkjet printing plus stamp transferring technique. The material usage efficiency is largely boosted. To our knowledge, these three novel patterning techniques presented in this study provide for the first time unprecedented capabilities for manufacturing organic and nanostructured electronic devices.by Jianglong Chen.Ph.D
- …