Reliable chip design from low powered unreliable components

The pace of technological improvement of the semiconductor market is driven by Moore’s Law, enabling chip transistor density to double every two years. The transistors would continue to decline in cost and size but increase in power. The continuous transistor scaling and extremely lower power constraints in modern Very Large Scale Integrated(VLSI) chips can potentially supersede the benefits of the technology shrinking due to reliability issues. As VLSI technology scales into nanoscale regime, fundamental physical limits are approached, and higher levels of variability, performance degradation, and higher rates of manufacturing defects are experienced. Soft errors, which traditionally affected only the memories, are now also resulting in logic circuit reliability degradation. A solution to these limitations is to integrate reliability assessment techniques into the Integrated Circuit(IC) design flow. This thesis investigates four aspects of reliability driven circuit design: a)Reliability estimation; b) Reliability optimization; c) Fault-tolerant techniques, and d) Delay degradation analysis. To guide the reliability driven synthesis and optimization of combinational circuits, highly accurate probability based reliability estimation methodology christened Conditional Probabilistic Error Propagation(CPEP) algorithm is developed to compute the impact of gate failures on the circuit output. CPEP guides the proposed rewriting based logic optimization algorithm employing local transformations. The main idea behind this methodology is to replace parts of the circuit with functionally equivalent but more reliable counterparts chosen from a precomputed subset of Negation-Permutation-Negation(NPN) classes of 4-variable functions. Cut enumeration and Boolean matching driven by reliability-aware optimization algorithm are used to identify the best possible replacement candidates. Experiments on a set of MCNC benchmark circuits and 8051 functional microcontroller units indicate that the proposed framework can achieve up to 75% reduction of output error probability. On average, about 14% SER reduction is obtained at the expense of very low area overhead of 6.57% that results in 13.52% higher power consumption. The next contribution of the research describes a novel methodology to design fault tolerant circuitry by employing the error correction codes known as Codeword Prediction Encoder(CPE). Traditional fault tolerant techniques analyze the circuit reliability issue from a static point of view neglecting the dynamic errors. In the context of communication and storage, the study of novel methods for reliable data transmission under unreliable hardware is an increasing priority. The idea of CPE is adapted from the field of forward error correction for telecommunications focusing on both encoding aspects and error correction capabilities. The proposed Augmented Encoding solution consists of computing an augmented codeword that contains both the codeword to be transmitted on the channel and extra parity bits. A Computer Aided Development(CAD) framework known as CPE simulator is developed providing a unified platform that comprises a novel encoder and fault tolerant LDPC decoders. Experiments on a set of encoders with different coding rates and different decoders indicate that the proposed framework can correct all errors under specific scenarios. On average, about 1000 times improvement in Soft Error Rate(SER) reduction is achieved. Last part of the research is the Inverse Gaussian Distribution(IGD) based delay model applicable to both combinational and sequential elements for sub-powered circuits. The Probability Density Function(PDF) based delay model accurately captures the delay behavior of all the basic gates in the library database. The IGD model employs these necessary parameters, and the delay estimation accuracy is demonstrated by evaluating multiple circuits. Experiments results indicate that the IGD based approach provides a high matching against HSPICE Monte Carlo simulation results, with an average error less than 1.9% and 1.2% for the 8-bit Ripple Carry Adder(RCA), and 8-bit De-Multiplexer(DEMUX) and Multiplexer(MUX) respectively

Low power predictable memory and processing architectures

Great demand in power optimized devices shows promising economic potential and draws lots of attention in industry and research area. Due to the continuously shrinking CMOS process, not only dynamic power but also static power has emerged as a big concern in power reduction. Other than power optimization, average-case power estimation is quite significant for power budget allocation but also challenging in terms of time and effort. In this thesis, we will introduce a methodology to support modular quantitative analysis in order to estimate average power of circuits, on the basis of two concepts named Random Bag Preserving and Linear Compositionality. It can shorten simulation time and sustain high accuracy, resulting in increasing the feasibility of power estimation of big systems. For power saving, firstly, we take advantages of the low power characteristic of adiabatic logic and asynchronous logic to achieve ultra-low dynamic and static power. We will propose two memory cells, which could run in adiabatic and non-adiabatic mode. About 90% dynamic power can be saved in adiabatic mode when compared to other up-to-date designs. About 90% leakage power is saved. Secondly, a novel logic, named Asynchronous Charge Sharing Logic (ACSL), will be introduced. The realization of completion detection is simplified considerably. Not just the power reduction improvement, ACSL brings another promising feature in average power estimation called data-independency where this characteristic would make power estimation effortless and be meaningful for modular quantitative average case analysis. Finally, a new asynchronous Arithmetic Logic Unit (ALU) with a ripple carry adder implemented using the logically reversible/bidirectional characteristic exhibiting ultra-low power dissipation with sub-threshold region operating point will be presented. The proposed adder is able to operate multi-functionally

Dependable Embedded Systems

This Open Access book introduces readers to many new techniques for enhancing and optimizing reliability in embedded systems, which have emerged particularly within the last five years. This book introduces the most prominent reliability concerns from today’s points of view and roughly recapitulates the progress in the community so far. Unlike other books that focus on a single abstraction level such circuit level or system level alone, the focus of this book is to deal with the different reliability challenges across different levels starting from the physical level all the way to the system level (cross-layer approaches). The book aims at demonstrating how new hardware/software co-design solution can be proposed to ef-fectively mitigate reliability degradation such as transistor aging, processor variation, temperature effects, soft errors, etc. Provides readers with latest insights into novel, cross-layer methods and models with respect to dependability of embedded systems; Describes cross-layer approaches that can leverage reliability through techniques that are pro-actively designed with respect to techniques at other layers; Explains run-time adaptation and concepts/means of self-organization, in order to achieve error resiliency in complex, future many core systems

Correct synthesis and integration of compiler-generated function units

PhD ThesisComputer architectures can use custom logic in addition to general pur- pose processors to improve performance for a variety of applications. The use of custom logic allows greater parallelism for some algorithms. While conventional CPUs typically operate on words, ne-grained custom logic can improve e ciency for many bit level operations. The commodi ca- tion of eld programmable devices, particularly FPGAs, has improved the viability of using custom logic in an architecture. This thesis introduces an approach to reasoning about the correctness of compilers that generate custom logic that can be synthesized to provide hardware acceleration for a given application. Compiler intermediate representations (IRs) and transformations that are relevant to genera- tion of custom logic are presented. Architectures may vary in the way that custom logic is incorporated, and suitable abstractions are used in order that the results apply to compilation for a variety of the design parameters that are introduced by the use of custom logic

Cell libraries and verification

Digital electronic devices are often implemented using cell libraries to provide the basic logic elements, such as Boolean functions and on-chip memories. To be usable both during the development of chips, which is usually done in a hardware definition language, and for the final layout, which consists of lithographic masks, cells are described in multiple ways. Among these, there are multiple descriptions of the behavior of cells, for example one at the level of hardware definition languages, and another one in terms of transistors that are ultimately produced. Thus, correct functioning of the device depends also on the correctness of the cell library, requiring all views of a cell to correspond with each other. In this thesis, techniques are presented to verify some of these correspondences in cell libraries. First, a technique is presented to check that the functional description in a hardware definition language and the transistor netlist description implement the same behavior. For this purpose, a semantics is defined for the commonly used subset of the hardware definition language Verilog. This semantics is encoded into Boolean equations, which can also be extracted from a transistor netlist. A model checker is then used to prove equivalence of these two descriptions, or to provide a counterexample showing that they are different. Also in basic elements such as cells, there exists non-determinism reflecting internal behavior that cannot be controlled from the outside. It is however desired that such internal behavior does not lead to different externally observable behavior, i.e., to different computation results. This thesis presents a technique to efficiently check, both for hardware definition language descriptions and transistor netlist descriptions, whether non-determinism does have an effect on the observable computation or not. Power consumption of chips has become a very important topic, especially since devices become mobile and therefore are battery powered. Thus, in order to predict and to maximize battery life, the power consumption of cells should be measured and reduced in an efficient way. To achieve these goals, this thesis also takes the power consumption into account when analyzing non-deterministic behavior. Then, on the one hand, behaviors consuming the same amount of power have to be measured only once. On the other hand, functionally equivalent computations can be forced to consume the least amount of power without affecting the externally observable behavior of the cell, for example by introducing appropriate delays. A way to prevent externally observable non-deterministic behavior in practical hardware designs is by adding timing checks. These checks rule out certain input patterns which must not be generated by the environment of a cell. If an input pattern can be found that is not forbidden by any of the timing checks, yet allows non-deterministic behavior, then the cell’s environment is not sufficiently restricted and hence this usually indicates a forgotten timing check. Therefore, the check for non-determinism is extended to also respect these timing checks and to consider only counterexamples that are not ruled out. If such a counterexample can be found, then it gives an indication what timing checks need to be added. Because current hardware designs run at very high speeds, timing analysis of cells has become a very important issue. For this purpose, cell libraries include a description of the delay arcs present in a cell, giving an amount of time it takes for an input change to have propagated to the outputs of a cell. Also for these descriptions, it is desired that they reflect the actual behavior in the cell. On the one hand, a delay arc that never manifests itself may result in a clock frequency that is lower than necessary. On the other hand, a forgotten delay arc can cause the clock frequency being too high, impairing functioning of the final chip. To relate the functional description of a cell with its timing specification, this thesis presents techniques to check whether delay arcs are consistent with the functionality, and which list all possible delay arcs. Computing new output values of a cell given some new input values requires all connections among the transistors in a cell to obtain stable values. Hitherto it was assumed that such a stable situation will always be reached eventually. To actually check this, a wire is abstracted into a sequence of stable values. Using this abstraction, checking whether stable situations are always reached is reduced to analyzing that an infinite sequence of such stable values exists. This is known in the term rewriting literature as productivity, the infinitary equivalent to termination. The final contribution in this thesis are techniques to automatically prove productivity. For this purpose, existing termination proving tools for term rewriting are re-used to benefit from their tremendous strength and their continuous improvements

Energy/power consumption model for an embedded processor board

This dissertation, whose research has been conducted at the Group of Electronic and Microelectronic Design (GDEM) within the framework of the project Power Consumption Control in Multimedia Terminals (PCCMUTE), focuses on the development of an energy estimation model for the battery-powered embedded processor board. The main objectives and contributions of the work are summarized as follows: A model is proposed to obtain the accurate energy estimation results based on the linear correlation between the performance monitoring counters (PMCs) and energy consumption. the uniqueness of the appropriate PMCs for each different system, the modeling methodology is improved to obtain stable accuracies with slight variations among multiple scenarios and to be repeatable in other systems. It includes two steps: the former, the PMC-filter, to identify the most proper set among the available PMCs of a system and the latter, the k-fold cross validation method, to avoid the bias during the model training stage. The methodology is implemented on a commercial embedded board running the 2.6.34 Linux kernel and the PAPI, a cross-platform interface to configure and access PMCs. The results show that the methodology is able to keep a good stability in different scenarios and provide robust estimation results with the average relative error being less than 5%. Este trabajo fin de máster, cuya investigación se ha desarrollado en el Grupo de Diseño Electrónico y Microelectrónico (GDEM) en el marco del proyecto PccMuTe, se centra en el desarrollo de un modelo de estimación de energía para un sistema empotrado alimentado por batería. Los objetivos principales y las contribuciones de esta tesis se resumen como sigue: Se propone un modelo para obtener estimaciones precisas del consumo de energía de un sistema empotrado. El modelo se basa en la correlación lineal entre los valores de los contadores de prestaciones y el consumo de energía. Considerando la particularidad de los contadores de prestaciones en cada sistema, la metodología de modelado se ha mejorado para obtener precisiones estables, con ligeras variaciones entre escenarios múltiples y para replicar los resultados en diferentes sistemas. La metodología incluye dos etapas: la primera, filtrado-PMC, que consiste en identificar el conjunto más apropiado de contadores de prestaciones de entre los disponibles en un sistema y la segunda, el método de validación cruzada de K iteraciones, cuyo fin es evitar los sesgos durante la fase de entrenamiento. La metodología se implementa en un sistema empotrado que ejecuta el kernel 2.6.34 de Linux y PAPI, un interfaz multiplataforma para configurar y acceder a los contadores. Los resultados muestran que esta metodología consigue una buena estabilidad en diferentes escenarios y proporciona unos resultados robustos de estimación con un error medio relativo inferior al 5%

The Fifth NASA Symposium on VLSI Design

The fifth annual NASA Symposium on VLSI Design had 13 sessions including Radiation Effects, Architectures, Mixed Signal, Design Techniques, Fault Testing, Synthesis, Signal Processing, and other Featured Presentations. The symposium provides insights into developments in VLSI and digital systems which can be used to increase data systems performance. The presentations share insights into next generation advances that will serve as a basis for future VLSI design

The 1992 4th NASA SERC Symposium on VLSI Design

Papers from the fourth annual NASA Symposium on VLSI Design, co-sponsored by the IEEE, are presented. Each year this symposium is organized by the NASA Space Engineering Research Center (SERC) at the University of Idaho and is held in conjunction with a quarterly meeting of the NASA Data System Technology Working Group (DSTWG). One task of the DSTWG is to develop new electronic technologies that will meet next generation electronic data system needs. The symposium provides insights into developments in VLSI and digital systems which can be used to increase data systems performance. The NASA SERC is proud to offer, at its fourth symposium on VLSI design, presentations by an outstanding set of individuals from national laboratories, the electronics industry, and universities. These speakers share insights into next generation advances that will serve as a basis for future VLSI design

Reactive processing for synchronous languages and its worst case reaction time analysis

Many embedded systems belong to the class of reactive systems. These are systems that have to react continuously to the environment at a rate that is determined by the environment. Reactive systems have two specific characteristics : their control flow requires concurrency and preemption, and, since the reactive systems are often safety-critical, we must be able to prove the correctness of the behavior and of the timing. To implement reactive systems, the synchronous languages were developed, which have a clear mathematical semantics and allow the expression of concurrency and preemption in a deterministic way. Programs in a synchronous language can be either compiled to software and run on a common processor, they can be synthesized to a hardware description, or a software/hardware co-design approach can be taken. However, the compilation of synchronous hardware into efficient code is not trivial. To improve the efficiency of the execution and at the same time simplify the compilation, reactive processors were introduced, which have an instruction set architecture that is inspired by synchronous languages. In particular, reactive processors have direct support for preemption and concurrency. Furthermore, these processors optimize the worst case reaction time, in contrast to common processors which optimize the average case reaction time. This simplifies the timing analysis, which is necessary to prove that a system meets its timing requirements. This thesis presents three contributions to reactive systems: - A formal semantics is given to the Kiel Esterel Processor (KEP), a reactive processor to execute the synchronous language Esterel. Also a compilation scheme from SyncCharts to the KEP assembler is presented, in addition to the existing compilation from Esterel into KEP assembler. - The Kiel Lustre Processor is introduced, a reactive processor for the synchronous dataflow language Lustre, which allows true parallel execution with multiple processing units. - Different approaches for the worst case reaction time analysis of KEP programs are presented: a search for the longest execution path in the KEP assembler, a formal modeling of the execution times based on interface algebras. Also an approach to use model checking to analyze the reaction time is applied to the KEP