1,712 research outputs found

    Technology exploration for adaptive power and frequency scaling in 90nm CMOS

    Get PDF
    In this paper we examine the expectations and limitations of design technologies such as adaptive voltage scaling (AVS) and adaptive body biasing (ABB) in a modern deep sub-micron process. To serve this purpose, a set of ring oscillators was fabricated in a 90nm triple-well CMOS technology. The analysis hereby presented is based on two ring oscillators running at 822MHz and 93MHz, respectively. Measurement results indicate that it is possible to reach 13.8x power savings by 3.4x frequency downscaling using AVS, ±11% power and ±8% frequency tuning at nominal conditions using ABB only, 22x power savings with 5x frequency downscaling by combining AVS and ABB, as well as 22x leakage reduction

    Systematic Comparison of HF CMOS Transconductors

    Get PDF
    Transconductors are commonly used as active elements in high-frequency (HF) filters, amplifiers, mixers, and oscillators. This paper reviews transconductor design by focusing on the V-I kernel that determines the key transconductor properties. Based on bandwidth considerations, simple V-I kernels with few or no internal nodes are preferred. In a systematic way, virtually all simple kernels published in literature are generated. This is done in two steps: 1) basic 3-terminal transconductors are covered and 2) then five different techniques to combine two of them in a composite V-I kernel. In order to compare transconductors in a fair way, a normalized signal-to-noise ratio (NSNR) is defined. The basic V-I kernels and the five classes of composite V-I kernels are then compared, leading to insight in the key mechanisms that affect NSNR. Symbolic equations are derived to estimate NSNR, while simulations with more advanced MOSFET models verify the results. The results show a strong tradeoff between NSNR and transconductance tuning range. Resistively generated MOSFETs render the best NSNR results and are robust for future technology developments

    Design Considerations of a Sub-50 {\mu}W Receiver Front-end for Implantable Devices in MedRadio Band

    Full text link
    Emerging health-monitor applications, such as information transmission through multi-channel neural implants, image and video communication from inside the body etc., calls for ultra-low active power (<50μ{\mu}W) high data-rate, energy-scalable, highly energy-efficient (pJ/bit) radios. Previous literature has strongly focused on low average power duty-cycled radios or low power but low-date radios. In this paper, we investigate power performance trade-off of each front-end component in a conventional radio including active matching, down-conversion and RF/IF amplification and prioritize them based on highest performance/energy metric. The analysis reveals 50Ω{\Omega} active matching and RF gain is prohibitive for 50μ{\mu}W power-budget. A mixer-first architecture with an N-path mixer and a self-biased inverter based baseband LNA, designed in TSMC 65nm technology show that sub 50μ{\mu}W performance can be achieved up to 10Mbps (< 5pJ/b) with OOK modulation.Comment: Accepted to appear on International Conference on VLSI Design 2018 (VLSID

    Body Bias Voltage Computations for Process and Temperature Compensation

    Full text link

    Resource Management Algorithms for Computing Hardware Design and Operations: From Circuits to Systems

    Get PDF
    The complexity of computation hardware has increased at an unprecedented rate for the last few decades. On the computer chip level, we have entered the era of multi/many-core processors made of billions of transistors. With transistor budget of this scale, many functions are integrated into a single chip. As such, chips today consist of many heterogeneous cores with intensive interaction among these cores. On the circuit level, with the end of Dennard scaling, continuously shrinking process technology has imposed a grand challenge on power density. The variation of circuit further exacerbated the problem by consuming a substantial time margin. On the system level, the rise of Warehouse Scale Computers and Data Centers have put resource management into new perspective. The ability of dynamically provision computation resource in these gigantic systems is crucial to their performance. In this thesis, three different resource management algorithms are discussed. The first algorithm assigns adaptivity resource to circuit blocks with a constraint on the overhead. The adaptivity improves resilience of the circuit to variation in a cost-effective way. The second algorithm manages the link bandwidth resource in application specific Networks-on-Chip. Quality-of-Service is guaranteed for time-critical traffic in the algorithm with an emphasis on power. The third algorithm manages the computation resource of the data center with precaution on the ill states of the system. Q-learning is employed to meet the dynamic nature of the system and Linear Temporal Logic is leveraged as a tool to describe temporal constraints. All three algorithms are evaluated by various experiments. The experimental results are compared to several previous work and show the advantage of our methods

    Voltage stacking for near/sub-threshold operation

    Get PDF

    Multi-objective Pareto front and particle swarm optimization algorithms for power dissipation reduction in microprocessors

    Get PDF
    The progress of microelectronics making possible higher integration densities, and a considerable development of on-board systems are currently undergoing, this growth comes up against a limiting factor of power dissipation. Higher power dissipation will cause an immediate spread of generated heat which causes thermal problems. Consequently, the system's total consumed energy will increase as the system temperature increase. High temperatures in microprocessors and large thermal energy of computer systems produce huge problems of system confidence, performance, and cooling expenses. Power consumed by processors are mainly due to the increase in number of cores and the clock frequency, which is dissipated in the form of heat and causes thermal challenges for chip designers. As the microprocessor’s performance has increased remarkably in Nano-meter technology, power dissipation is becoming non-negligible. To solve this problem, this article addresses power dissipation reduction issues for high performance processors using multi-objective Pareto front (PF), and particle swarm optimization (PSO) algorithms to achieve power dissipation as a prior computation that reduces the real delay of a target microprocessor unit. Simulation is verified the conceptual fundamentals and optimization of joint body and supply voltages (Vth-VDD) which showing satisfactory findings

    UE Uplink Power Distribution for M2M over LTE

    Get PDF

    Adaptive Baseband Pro cessing and Configurable Hardware for Wireless Communication

    Get PDF
    The world of information is literally at one’s fingertips, allowing access to previously unimaginable amounts of data, thanks to advances in wireless communication. The growing demand for high speed data has necessitated theuse of wider bandwidths, and wireless technologies such as Multiple-InputMultiple-Output (MIMO) have been adopted to increase spectral efficiency.These advanced communication technologies require sophisticated signal processing, often leading to higher power consumption and reduced battery life.Therefore, increasing energy efficiency of baseband hardware for MIMO signal processing has become extremely vital. High Quality of Service (QoS)requirements invariably lead to a larger number of computations and a higherpower dissipation. However, recognizing the dynamic nature of the wirelesscommunication medium in which only some channel scenarios require complexsignal processing, and that not all situations call for high data rates, allowsthe use of an adaptive channel aware signal processing strategy to provide adesired QoS. Information such as interference conditions, coherence bandwidthand Signal to Noise Ratio (SNR) can be used to reduce algorithmic computations in favorable channels. Hardware circuits which run these algorithmsneed flexibility and easy reconfigurability to switch between multiple designsfor different parameters. These parameters can be used to tune the operations of different components in a receiver based on feedback from the digitalbaseband. This dissertation focuses on the optimization of digital basebandcircuitry of receivers which use feedback to trade power and performance. Aco-optimization approach, where designs are optimized starting from the algorithmic stage through the hardware architectural stage to the final circuitimplementation is adopted to realize energy efficient digital baseband hardwarefor mobile 4G devices. These concepts are also extended to the next generation5G systems where the energy efficiency of the base station is improved.This work includes six papers that examine digital circuits in MIMO wireless receivers. Several key blocks in these receiver include analog circuits thathave residual non-linearities, leading to signal intermodulation and distortion.Paper-I introduces a digital technique to detect such non-linearities and calibrate analog circuits to improve signal quality. The concept of a digital nonlinearity tuning system developed in Paper-I is implemented and demonstratedin hardware. The performance of this implementation is tested with an analogchannel select filter, and results are presented in Paper-II. MIMO systems suchas the ones used in 4G, may employ QR Decomposition (QRD) processors tosimplify the implementation of tree search based signal detectors. However,the small form factor of the mobile device increases spatial correlation, whichis detrimental to signal multiplexing. Consequently, a QRD processor capableof handling high spatial correlation is presented in Paper-III. The algorithm and hardware implementation are optimized for carrier aggregation, which increases requirements on signal processing throughput, leading to higher powerdissipation. Paper-IV presents a method to perform channel-aware processingwith a simple interpolation strategy to adaptively reduce QRD computationcount. Channel properties such as coherence bandwidth and SNR are used toreduce multiplications by 40% to 80%. These concepts are extended to usetime domain correlation properties, and a full QRD processor for 4G systemsfabricated in 28 nm FD-SOI technology is presented in Paper-V. The designis implemented with a configurable architecture and measurements show thatcircuit tuning results in a highly energy efficient processor, requiring 0.2 nJ to1.3 nJ for each QRD. Finally, these adaptive channel-aware signal processingconcepts are examined in the scope of the next generation of communicationsystems. Massive MIMO systems increase spectral efficiency by using a largenumber of antennas at the base station. Consequently, the signal processingat the base station has a high computational count. Paper-VI presents a configurable detection scheme which reduces this complexity by using techniquessuch as selective user detection and interpolation based signal processing. Hardware is optimized for resource sharing, resulting in a highly reconfigurable andenergy efficient uplink signal detector

    A systematic approach to circuit design and analysis: classification of Two-VCCS Circuits

    Get PDF
    This paper discusses a systematic approach to the design and analysis of circuits, using a transconductor or voltage controlled current source (VCCS) as a building block. It is shown that two independent Kirchhoff relations among the VCCS voltages and currents play a crucial role in establishing a unique transfer function in two-port circuits with two VCCSs. A class of two VCCS circuits is defined, which can be subdivided into three main classes and 14 subclasses, based on different imposable sets of two Kirchhoff relations. The classification is useful for circuit synthesis and analysis, as it reveals all the basically different ways to exploit two VCCS's, and allows for a unified analysis of classes of circuits. To exemplify this, all complementary metal-oxide-semiconductor (CMOS) V-I converter kernels, based on two matched MOS transistor (MOST)-VCCSs, are generated and analyzed with respect to distortion. It is shown that dozens of published transconductor circuits can be classified in only four classes, with essentially different distortion behavio
    corecore