Reliability-aware and energy-efficient system level design for networks-on-chip

2015 Spring.Includes bibliographical references.With CMOS technology aggressively scaling into the ultra-deep sub-micron (UDSM) regime and application complexity growing rapidly in recent years, processors today are being driven to integrate multiple cores on a chip. Such chip multiprocessor (CMP) architectures offer unprecedented levels of computing performance for highly parallel emerging applications in the era of digital convergence. However, a major challenge facing the designers of these emerging multicore architectures is the increased likelihood of failure due to the rise in transient, permanent, and intermittent faults caused by a variety of factors that are becoming more and more prevalent with technology scaling. On-chip interconnect architectures are particularly susceptible to faults that can corrupt transmitted data or prevent it from reaching its destination. Reliability concerns in UDSM nodes have in part contributed to the shift from traditional bus-based communication fabrics to network-on-chip (NoC) architectures that provide better scalability, performance, and utilization than buses. In this thesis, to overcome potential faults in NoCs, my research began by exploring fault-tolerant routing algorithms. Under the constraint of deadlock freedom, we make use of the inherent redundancy in NoCs due to multiple paths between packet sources and sinks and propose different fault-tolerant routing schemes to achieve much better fault tolerance capabilities than possible with traditional routing schemes. The proposed schemes also use replication opportunistically to optimize the balance between energy overhead and arrival rate. As 3D integrated circuit (3D-IC) technology with wafer-to-wafer bonding has been recently proposed as a promising candidate for future CMPs, we also propose a fault-tolerant routing scheme for 3D NoCs which outperforms the existing popular routing schemes in terms of energy consumption, performance and reliability. To quantify reliability and provide different levels of intelligent protection, for the first time, we propose the network vulnerability factor (NVF) metric to characterize the vulnerability of NoC components to faults. NVF determines the probabilities that faults in NoC components manifest as errors in the final program output of the CMP system. With NVF aware partial protection for NoC components, almost 50% energy cost can be saved compared to the traditional approach of comprehensively protecting all NoC components. Lastly, we focus on the problem of fault-tolerant NoC design, that involves many NP-hard sub-problems such as core mapping, fault-tolerant routing, and fault-tolerant router configuration. We propose a novel design-time (RESYN) and a hybrid design and runtime (HEFT) synthesis framework to trade-off energy consumption and reliability in the NoC fabric at the system level for CMPs. Together, our research in fault-tolerant NoC routing, reliability modeling, and reliability aware NoC synthesis substantially enhances NoC reliability and energy-efficiency beyond what is possible with traditional approaches and state-of-the-art strategies from prior work

High-level services for networks-on-chip

Future technology trends envision that next-generation Multiprocessors Systems-on- Chip (MPSoCs) will be composed of a combination of a large number of processing and storage elements interconnected by complex communication architectures. Communication and interconnection between these basic blocks play a role of crucial importance when the number of these elements increases. Enabling reliable communication channels between cores becomes therefore a challenge for system designers. Networks-on-Chip (NoCs) appeared as a strategy for connecting and managing the communication between several design elements and IP blocks, as required in complex Systems-on-Chip (SoCs). The topic can be considered as a multidisciplinary synthesis of multiprocessing, parallel computing, networking, and on- chip communication domains. Networks-on-Chip, in addition to standard communication services, can be employed for providing support for the implementation of system-level services. This dissertation will demonstrate how high-level services can be added to an MPSoC platform by embedding appropriate hardware/software support in the network interfaces (NIs) of the NoC. In this dissertation, the implementation of innovative modules acting in parallel with protocol translation and data transmission in NIs is proposed and evaluated. The modules can support the execution of the high-level services in the NoC at a relatively low cost in terms of area and energy consumption. Three types of services will be addressed and discussed: security, monitoring, and fault tolerance. With respect to the security aspect, this dissertation will discuss the implementation of an innovative data protection mechanism for detecting and preventing illegal accesses to protected memory blocks and/or memory mapped peripherals. The second aspect will be addressed by proposing the implementation of a monitoring system based on programmable multipurpose monitoring probes aimed at detecting NoC internal events and run-time characteristics. As last topic, new architectural solutions for the design of fault tolerant network interfaces will be presented and discussed

Développement d'architectures HW/SW tolérantes aux fautes et auto-calibrantes pour les technologies Intégrées 3D

Malgré les avantages de l'intégration 3D, le test, le rendement et la fiabilité des Through-Silicon-Vias (TSVs) restent parmi les plus grands défis pour les systèmes 3D à base de Réseaux-sur-Puce (Network-on-Chip - NoC). Dans cette thèse, une stratégie de test hors-ligne a été proposé pour les interconnections TSV des liens inter-die des NoCs 3D. Pour le TSV Interconnect Built-In Self-Test (TSV-IBIST) on propose une nouvelle stratégie pour générer des vecteurs de test qui permet la détection des fautes structuraux (open et short) et paramétriques (fautes de délaye). Des stratégies de correction des fautes transitoires et permanents sur les TSV sont aussi proposées aux plusieurs niveaux d'abstraction: data link et network. Au niveau data link, des techniques qui utilisent des codes de correction (ECC) et retransmission sont utilisées pour protégé les liens verticales. Des codes de correction sont aussi utilisés pour la protection au niveau network. Les défauts de fabrication ou vieillissement des TSVs sont réparé au niveau data link avec des stratégies à base de redondance et sérialisation. Dans le réseau, les liens inter-die défaillante ne sont pas utilisables et un algorithme de routage tolérant aux fautes est proposé. On peut implémenter des techniques de tolérance aux fautes sur plusieurs niveaux. Les résultats ont montré qu'une stratégie multi-level atteint des très hauts niveaux de fiabilité avec un cout plus bas. Malheureusement, il n'y as pas une solution unique et chaque stratégie a ses avantages et limitations. C'est très difficile d'évaluer tôt dans le design flow les couts et l'impact sur la performance. Donc, une méthodologie d'exploration de la résilience aux fautes est proposée pour les NoC 3D mesh.3D technology promises energy-efficient heterogeneous integrated systems, which may open the way to thousands cores chips. Silicon dies containing processing elements are stacked and connected by vertical wires called Through-Silicon-Vias. In 3D chips, interconnecting an increasing number of processing elements requires a scalable high-performance interconnect solution: the 3D Network-on-Chip. Despite the advantages of 3D integration, testing, reliability and yield remain the major challenges for 3D NoC-based systems. In this thesis, the TSV interconnect test issue is addressed by an off-line Interconnect Built-In Self-Test (IBIST) strategy that detects both structural (i.e. opens, shorts) and parametric faults (i.e. delays and delay due to crosstalk). The IBIST circuitry implements a novel algorithm based on the aggressor-victim scenario and alleviates limitations of existing strategies. The proposed Kth-aggressor fault (KAF) model assumes that the aggressors of a victim TSV are neighboring wires within a distance given by the aggressor order K. Using this model, TSV interconnect tests of inter-die 3D NoC links may be performed for different aggressor order, reducing test times and circuitry complexity. In 3D NoCs, TSV permanent and transient faults can be mitigated at different abstraction levels. In this thesis, several error resilience schemes are proposed at data link and network levels. For transient faults, 3D NoC links can be protected using error correction codes (ECC) and retransmission schemes using error detection (Automatic Retransmission Query) and correction codes (i.e. Hybrid error correction and retransmission).For transients along a source-destination path, ECC codes can be implemented at network level (i.e. Network-level Forward Error Correction). Data link solutions also include TSV repair schemes for faults due to fabrication processes (i.e. TSV-Spare-and-Replace and Configurable Serial Links) and aging (i.e. Interconnect Built-In Self-Repair and Adaptive Serialization) defects. At network-level, the faulty inter-die links of 3D mesh NoCs are repaired by implementing a TSV fault-tolerant routing algorithm. Although single-level solutions can achieve the desired yield / reliability targets, error mitigation can be realized by a combination of approaches at several abstraction levels. To this end, multi-level error resilience strategies have been proposed. Experimental results show that there are cases where this multi-layer strategy pays-off both in terms of cost and performance. Unfortunately, one-fits-all solution does not exist, as each strategy has its advantages and limitations. For system designers, it is very difficult to assess early in the design stages the costs and the impact on performance of error resilience. Therefore, an error resilience exploration (ERX) methodology is proposed for 3D NoCs.SAVOIE-SCD - Bib.électronique (730659901) / SudocGRENOBLE1/INP-Bib.électronique (384210012) / SudocGRENOBLE2/3-Bib.électronique (384219901) / SudocSudocFranceF

On Fault Tolerance Methods for Networks-on-Chip

Technology scaling has proceeded into dimensions in which the reliability of manufactured devices is becoming endangered. The reliability decrease is a consequence of physical limitations, relative increase of variations, and decreasing noise margins, among others. A promising solution for bringing the reliability of circuits back to a desired level is the use of design methods which introduce tolerance against possible faults in an integrated circuit. This thesis studies and presents fault tolerance methods for network-onchip (NoC) which is a design paradigm targeted for very large systems-onchip. In a NoC resources, such as processors and memories, are connected to a communication network; comparable to the Internet. Fault tolerance in such a system can be achieved at many abstraction levels. The thesis studies the origin of faults in modern technologies and explains the classification to transient, intermittent and permanent faults. A survey of fault tolerance methods is presented to demonstrate the diversity of available methods. Networks-on-chip are approached by exploring their main design choices: the selection of a topology, routing protocol, and flow control method. Fault tolerance methods for NoCs are studied at different layers of the OSI reference model. The data link layer provides a reliable communication link over a physical channel. Error control coding is an efficient fault tolerance method especially against transient faults at this abstraction level. Error control coding methods suitable for on-chip communication are studied and their implementations presented. Error control coding loses its effectiveness in the presence of intermittent and permanent faults. Therefore, other solutions against them are presented. The introduction of spare wires and split transmissions are shown to provide good tolerance against intermittent and permanent errors and their combination to error control coding is illustrated. At the network layer positioned above the data link layer, fault tolerance can be achieved with the design of fault tolerant network topologies and routing algorithms. Both of these approaches are presented in the thesis together with realizations in the both categories. The thesis concludes that an optimal fault tolerance solution contains carefully co-designed elements from different abstraction levelsSiirretty Doriast

Runtime Detection of a Bandwidth Denial Attack from a Rogue Network-on-Chip

Chips with high computational power are the crux of today’s pervasive complex digital systems. Microprocessor circuits are evolving towards many core designs with the integration of hundreds of processing cores, memory elements and other devices on a single chip to sustain high performance computing while maintaining low design costs. Two decisive paradigm shifts in the semiconductor industry have made this evolution possible: (a) architectural and (b) organizational. At the heart of the architectural innovation is a scalable high speed data communication structure, the network-on-chip (NoC). NoC is an interconnect network for the glueless integration of on-chip components in the modern complex communication centric designs. In the recent days, NoC has replaced the traditional bus based architecture owing to its structured and modular design, scalability and low design cost. The organizational revolution has resulted in a globalized and collaborative supply chain with pervasive use of third party intellectual properties to reduce the time-to-market and overall design costs. Despite the advantages of these paradigm shifts, modern system-on-chips pose a plethora of security vulnerabilities. This work explores a threat model arising from a malicious NoC IP embedded with a hardware trojan affecting the resource availability of on-chip components. A rigorous simulation infrastructure is established to evaluate the feasibility and potency of such an attack. Further, a non-invasive runtime monitoring technique is proposed and thoroughly investigated to ensure the trustworthiness of a third party NoC IP with low overheads

System-on-chip Computing and Interconnection Architectures for Telecommunications and Signal Processing

This dissertation proposes novel architectures and design techniques targeting SoC building blocks for telecommunications and signal processing applications. Hardware implementation of Low-Density Parity-Check decoders is approached at both the algorithmic and the architecture level. Low-Density Parity-Check codes are a promising coding scheme for future communication standards due to their outstanding error correction performance. This work proposes a methodology for analyzing effects of finite precision arithmetic on error correction performance and hardware complexity. The methodology is throughout employed for co-designing the decoder. First, a low-complexity check node based on the P-output decoding principle is designed and characterized on a CMOS standard-cells library. Results demonstrate implementation loss below 0.2 dB down to BER of 10^{-8} and a saving in complexity up to 59% with respect to other works in recent literature. High-throughput and low-latency issues are addressed with modified single-phase decoding schedules. A new "memory-aware" schedule is proposed requiring down to 20% of memory with respect to the traditional two-phase flooding decoding. Additionally, throughput is doubled and logic complexity reduced of 12%. These advantages are traded-off with error correction performance, thus making the solution attractive only for long codes, as those adopted in the DVB-S2 standard. The "layered decoding" principle is extended to those codes not specifically conceived for this technique. Proposed architectures exhibit complexity savings in the order of 40% for both area and power consumption figures, while implementation loss is smaller than 0.05 dB. Most modern communication standards employ Orthogonal Frequency Division Multiplexing as part of their physical layer. The core of OFDM is the Fast Fourier Transform and its inverse in charge of symbols (de)modulation. Requirements on throughput and energy efficiency call for FFT hardware implementation, while ubiquity of FFT suggests the design of parametric, re-configurable and re-usable IP hardware macrocells. In this context, this thesis describes an FFT/IFFT core compiler particularly suited for implementation of OFDM communication systems. The tool employs an accuracy-driven configuration engine which automatically profiles the internal arithmetic and generates a core with minimum operands bit-width and thus minimum circuit complexity. The engine performs a closed-loop optimization over three different internal arithmetic models (fixed-point, block floating-point and convergent block floating-point) using the numerical accuracy budget given by the user as a reference point. The flexibility and re-usability of the proposed macrocell are illustrated through several case studies which encompass all current state-of-the-art OFDM communications standards (WLAN, WMAN, xDSL, DVB-T/H, DAB and UWB). Implementations results are presented for two deep sub-micron standard-cells libraries (65 and 90 nm) and commercially available FPGA devices. Compared with other FFT core compilers, the proposed environment produces macrocells with lower circuit complexity and same system level performance (throughput, transform size and numerical accuracy). The final part of this dissertation focuses on the Network-on-Chip design paradigm whose goal is building scalable communication infrastructures connecting hundreds of core. A low-complexity link architecture for mesochronous on-chip communication is discussed. The link enables skew constraint looseness in the clock tree synthesis, frequency speed-up, power consumption reduction and faster back-end turnarounds. The proposed architecture reaches a maximum clock frequency of 1 GHz on 65 nm low-leakage CMOS standard-cells library. In a complex test case with a full-blown NoC infrastructure, the link overhead is only 3% of chip area and 0.5% of leakage power consumption. Finally, a new methodology, named metacoding, is proposed. Metacoding generates correct-by-construction technology independent RTL codebases for NoC building blocks. The RTL coding phase is abstracted and modeled with an Object Oriented framework, integrated within a commercial tool for IP packaging (Synopsys CoreTools suite). Compared with traditional coding styles based on pre-processor directives, metacoding produces 65% smaller codebases and reduces the configurations to verify up to three orders of magnitude

Virtual Runtime Application Partitions for Resource Management in Massively Parallel Architectures

This thesis presents a novel design paradigm, called Virtual Runtime Application Partitions (VRAP), to judiciously utilize the on-chip resources. As the dark silicon era approaches, where the power considerations will allow only a fraction chip to be powered on, judicious resource management will become a key consideration in future designs. Most of the works on resource management treat only the physical components (i.e. computation, communication, and memory blocks) as resources and manipulate the component to application mapping to optimize various parameters (e.g. energy efficiency). To further enhance the optimization potential, in addition to the physical resources we propose to manipulate abstract resources (i.e. voltage/frequency operating point, the fault-tolerance strength, the degree of parallelism, and the configuration architecture). The proposed framework (i.e. VRAP) encapsulates methods, algorithms, and hardware blocks to provide each application with the abstract resources tailored to its needs. To test the efficacy of this concept, we have developed three distinct self adaptive environments: (i) Private Operating Environment (POE), (ii) Private Reliability Environment (PRE), and (iii) Private Configuration Environment (PCE) that collectively ensure that each application meets its deadlines using minimal platform resources. In this work several novel architectural enhancements, algorithms and policies are presented to realize the virtual runtime application partitions efficiently. Considering the future design trends, we have chosen Coarse Grained Reconfigurable Architectures (CGRAs) and Network on Chips (NoCs) to test the feasibility of our approach. Specifically, we have chosen Dynamically Reconfigurable Resource Array (DRRA) and McNoC as the representative CGRA and NoC platforms. The proposed techniques are compared and evaluated using a variety of quantitative experiments. Synthesis and simulation results demonstrate VRAP significantly enhances the energy and power efficiency compared to state of the art.Siirretty Doriast

Decompose and Conquer: Addressing Evasive Errors in Systems on Chip

Modern computer chips comprise many components, including microprocessor cores, memory modules, on-chip networks, and accelerators. Such system-on-chip (SoC) designs are deployed in a variety of computing devices: from internet-of-things, to smartphones, to personal computers, to data centers. In this dissertation, we discuss evasive errors in SoC designs and how these errors can be addressed efficiently. In particular, we focus on two types of errors: design bugs and permanent faults. Design bugs originate from the limited amount of time allowed for design verification and validation. Thus, they are often found in functional features that are rarely activated. Complete functional verification, which can eliminate design bugs, is extremely time-consuming, thus impractical in modern complex SoC designs. Permanent faults are caused by failures of fragile transistors in nano-scale semiconductor manufacturing processes. Indeed, weak transistors may wear out unexpectedly within the lifespan of the design. Hardware structures that reduce the occurrence of permanent faults incur significant silicon area or performance overheads, thus they are infeasible for most cost-sensitive SoC designs. To tackle and overcome these evasive errors efficiently, we propose to leverage the principle of decomposition to lower the complexity of the software analysis or the hardware structures involved. To this end, we present several decomposition techniques, specific to major SoC components. We first focus on microprocessor cores, by presenting a lightweight bug-masking analysis that decomposes a program into individual instructions to identify if a design bug would be masked by the program's execution. We then move to memory subsystems: there, we offer an efficient memory consistency testing framework to detect buggy memory-ordering behaviors, which decomposes the memory-ordering graph into small components based on incremental differences. We also propose a microarchitectural patching solution for memory subsystem bugs, which augments each core node with a small distributed programmable logic, instead of including a global patching module. In the context of on-chip networks, we propose two routing reconfiguration algorithms that bypass faulty network resources. The first computes short-term routes in a distributed fashion, localized to the fault region. The second decomposes application-aware routing computation into simple routing rules so to quickly find deadlock-free, application-optimized routes in a fault-ridden network. Finally, we consider general accelerator modules in SoC designs. When a system includes many accelerators, there are a variety of interactions among them that must be verified to catch buggy interactions. To this end, we decompose such inter-module communication into basic interaction elements, which can be reassembled into new, interesting tests. Overall, we show that the decomposition of complex software algorithms and hardware structures can significantly reduce overheads: up to three orders of magnitude in the bug-masking analysis and the application-aware routing, approximately 50 times in the routing reconfiguration latency, and 5 times on average in the memory-ordering graph checking. These overhead reductions come with losses in error coverage: 23% undetected bug-masking incidents, 39% non-patchable memory bugs, and occasionally we overlook rare patterns of multiple faults. In this dissertation, we discuss the ideas and their trade-offs, and present future research directions.PHDComputer Science & EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/147637/1/doowon_1.pd

Analyse und Erweiterung eines fehler-toleranten NoC für SRAM-basierte FPGAs in Weltraumapplikationen

Data Processing Units for scientific space mission need to process ever higher volumes of data and perform ever complex calculations. But the performance of available space-qualified general purpose processors is just in the lower three digit megahertz range, which is already insufficient for some applications. As an alternative, suitable processing steps can be implemented in hardware on a space-qualified SRAM-based FPGA. However, suitable devices are susceptible against space radiation. At the Institute for Communication and Network Engineering a fault-tolerant, network-based communication architecture was developed, which enables the construction of processing chains on the basis of different processing modules within suitable SRAM-based FPGAs and allows the exchange of single processing modules during runtime, too. The communication architecture and its protocol shall isolate non SEU mitigated or just partial SEU mitigated modules affected by radiation-induced faults to prohibit the propagation of errors within the remaining System-on-Chip. In the context of an ESA study, this communication architecture was extended with further components and implemented in a representative hardware platform. Based on the acquired experiences during the study, this work analyses the actual fault-tolerance characteristics as well as weak points of this initial implementation. At appropriate locations, the communication architecture was extended with mechanisms for fault-detection and fault-differentiation as well as with a hardware-based monitoring solution. Both, the former measures and the extension of the employed hardware-platform with selective fault-injection capabilities for the emulation of radiation-induced faults within critical areas of a non SEU mitigated processing module, are used to evaluate the effects of radiation-induced faults within the communication architecture. By means of the gathered results, further measures to increase fast detection and isolation of faulty nodes are developed, selectively implemented and verified. In particular, the ability of the communication architecture to isolate network nodes without SEU mitigation could be significantly improved.Instrumentenrechner für wissenschaftliche Weltraummissionen müssen ein immer höheres Datenvolumen verarbeiten und immer komplexere Berechnungen ausführen. Die Performanz von verfügbaren qualifizierten Universalprozessoren liegt aber lediglich im unteren dreistelligen Megahertz-Bereich, was für einige Anwendungen bereits nicht mehr ausreicht. Als Alternative bietet sich die Implementierung von entsprechend geeigneten Datenverarbeitungsschritten in Hardware auf einem qualifizierten SRAM-basierten FPGA an. Geeignete Bausteine sind jedoch empfindlich gegenüber der Strahlungsumgebung im Weltraum. Am Institut für Datentechnik und Kommunikationsnetze wurde eine fehlertolerante netzwerk-basierte Kommunikationsarchitektur entwickelt, die innerhalb eines geeigneten SRAM-basierten FPGAs Datenverarbeitungsmodule miteinander nach Bedarf zu Verarbeitungsketten verbindet, sowie den Austausch von einzelnen Modulen im Betrieb ermöglicht. Nicht oder nur partiell SEU mitigierte Module sollen bei strahlungsbedingten Fehlern im Modul durch das Protokoll und die Fehlererkennungsmechanismen der Kommunikationsarchitektur isoliert werden, um ein Ausbreiten des Fehlers im restlichen System-on-Chip zu verhindern. Im Kontext einer ESA Studie wurde diese Kommunikationsarchitektur um Komponenten erweitert und auf einer repräsentativen Hardwareplattform umgesetzt. Basierend auf den gesammelten Erfahrungen aus der Studie, wird in dieser Arbeit eine Analyse der tatsächlichen Fehlertoleranz-Eigenschaften sowie der Schwachstellen dieser ursprünglichen Implementierung durchgeführt. Die Kommunikationsarchitektur wurde an geeigneten Stellen um Fehlerdetektierungs- und Fehlerunterscheidungsmöglichkeiten erweitert, sowie um eine hardwarebasierte Überwachung ergänzt. Sowohl diese Maßnahmen, als auch die Erweiterung der Hardwareplattform um gezielte Fehlerinjektions-Möglichkeiten zum Emulieren von strahlungsinduzierten Fehlern in kritischen Komponenten eines nicht SEU mitigierten Prozessierungsmoduls werden genutzt, um die tatsächlichen auftretenden Effekte in der Kommunikationsarchitektur zu evaluieren. Anhand der Ergebnisse werden weitere Verbesserungsmaßnahmen speziell zur schnellen Detektierung und Isolation von fehlerhaften Knoten erarbeitet, selektiv implementiert und verifiziert. Insbesondere die Fähigkeit, fehlerhafte, nicht SEU mitigierte Netzwerkknoten innerhalb der Kommunikationsarchitektur zu isolieren, konnte dabei deutlich verbessert werden