End-of-Life and Constant Rate Reliability Modeling for Semiconductor Packages Using Knowledge-Based Test Approaches

End-of-life and constant rate reliability modeling for semiconductor packages are the focuses of this dissertation. Knowledge-based testing approaches are applied and the test-to-failure approach is approved to be a reliable approach. First of all, the end-of-life AF models for solder joint reliability are studied. The research results show using one universal AF model for all packages is flawed approach. An assessment matrix is generated to guide the application of AF models. The AF models chosen should be either assessed based on available data or validated through accelerated stress tests. A common model can be applied if the packages have similar structures and materials. The studies show that different AF models will be required for SnPb solder joints and SAC lead-free solder joints. Second, solder bumps under power cycling conditions are found to follow constant rate reliability models due to variations of the operating conditions. Case studies demonstrate that a constant rate reliability model is appropriate to describe non solder joint related semiconductor package failures as well. Third, the dissertation describes the rate models using Chi-square approach cannot correlate well with the expected failure mechanisms in field applications. The estimation of the upper bound using a Chi-square value from zero failure is flawed. The dissertation emphasizes that the failure data is required for the failure rate estimation. A simple but tighter approach is proposed and provides much tighter bounds in comparison of other approaches available. Last, the reliability of solder bumps in flip chip packages under power cycling conditions is studied. The bump materials and underfill materials will significantly influence the reliability of the solder bumps. A set of comparable bump materials and the underfill materials will dramatically improve the end-of-life solder bumps under power cycling loads, and bump materials are one of the most significant factors. Comparing to the field failure data obtained, the end-of-life model does not predict the failures in the field, which is more close to an approximately constant failure rate. In addition, the studies find an improper underfill material could change the failure location from solder bump cracking to ILD cracking or BGA solder joint failures

PCB Quality Metrics that Drive Reliability (PD 18)

Risk based technology infusion is a deliberate and systematic process which defines the analysis and communication methodology by which new technology is applied and integrated into existing and new designs, identifies technology development needs based on trends analysis and facilitates the identification of shortfalls against performance objectives. This presentation at IPC Works Asia Aerospace 2019 Events provides the audience a snapshot of quality variations in printed wiring board quality, as assessed, using experiences in processing and risk analysis of PWB structural integrity coupons. The presentation will focus on printed wiring board quality metrics used, the relative type and number of non-conformances observed and trend analysis using statistical methods. Trend analysis shows the top five non-conformances observed across PWB suppliers, the root cause(s) behind these non-conformance and suggestions of mitigation plans. The trends will then be matched with the current state of the PWB supplier base and its challenges and opportunities. The presentation further discusses the risk based SMA approaches and methods being applied at GSFC for evaluating candidate printed wiring board technologies which promote the adoption of higher throughput and faster processing technology for GSFC missions

Prognostics and health management of light emitting diodes

Prognostics is an engineering process of diagnosing, predicting the remaining useful life and estimating the reliability of systems and products. Prognostics and Health Management (PHM) has emerged in the last decade as one of the most efficient approaches in failure prevention, reliability estimation and remaining useful life predictions of various engineering systems and products. Light Emitting Diodes (LEDs) are optoelectronic micro-devices that are now replacing traditional incandescent and fluorescent lighting, as they have many advantages including higher reliability, greater energy efficiency, long life time and faster switching speed. Even though LEDs have high reliability and long life time, manufacturers and lighting systems designers still need to assess the reliability of LED lighting systems and the failures in the LED. This research provides both experimental and theoretical results that demonstrate the use of prognostics and health monitoring techniques for high power LEDs subjected to harsh operating conditions. Data driven, model driven and fusion prognostics approaches are developed to monitor and identify LED failures, based on the requirement for the light output power. The approaches adopted in this work are validated and can be used to assess the life of an LED lighting system after their deployment based on the power of the light output emitted. The data driven techniques are only based on monitoring selected operational and performance indicators using sensors whereas the model driven technique is based on sensor data as well as on a developed empirical model. Fusion approach is also developed using the data driven and the model driven approaches to the LED. Real-time implementation of developed approaches are also investigated and discussed

JTEC Panel report on electronic manufacturing and packaging in Japan

This report summarizes the status of electronic manufacturing and packaging technology in Japan in comparison to that in the United States, and its impact on competition in electronic manufacturing in general. In addition to electronic manufacturing technologies, the report covers technology and manufacturing infrastructure, electronics manufacturing and assembly, quality assurance and reliability in the Japanese electronics industry, and successful product realization strategies. The panel found that Japan leads the United States in almost every electronics packaging technology. Japan clearly has achieved a strategic advantage in electronics production and process technologies. Panel members believe that Japanese competitors could be leading U.S. firms by as much as a decade in some electronics process technologies

Achieving Improved Reliability with Failure Analysis

Reliability is the ability of a product to properly function, within specified performance limits, for a specified period of time, under the life cycle application conditions. Failure analysis is a vital tool in the effort to ensure reliability of electronic products and systems throughout their product lifecycle. Today, organizations involved in activities within the electronics supply chain are facing new challenges, not just from complex assembly styles, harsher lifecycle environments, and sophisticated supply chains, but also from customers who are demanding a quicker turn-around. Unfortunately, root cause failure analysis is often performed incompletely, leading to a poor understanding of failure mechanisms and causes and, customer dissatisfaction due to recurring failures. The PDC (Professional Development Course) starts with an introduction to reliability concepts, physics of failure and an overview of failure mechanisms that affect PCBs (Printed Circuit Boards), PCBAs (Printed Circuit Board Assembly) and components. The PDC then dives into root cause hypothesizing techniques (Pareto, FMEA (Failure Modes and Effects Analysis), fishbone (Cause-And-Effect Diagram), FTA (Fault Tree Analysis)), non-destructive and destructive analysis and, materials characterization will be discussed. Numerous failure analysis case studies will be used to illustrate the techniques and analysis principles to arrive at the root cause(s) of field failures on printed circuit boards, active components, and assemblies. What Attendees will Learn: Topics include: Overview of Reliability Concepts Failure mechanisms of electronic products Root cause analysis Failure analysis techniques -Non-destructive techniques (optical, CSAM (Confocal Scanning Electron Microscopy) etc.) -Destructive analysis (DPA (Destructive Physical Analysis), Decap (Decapsulation), FIB (Focused Ion Beam) etc.) -Materials characterization (XRF (X-Ray Fluorescence) , EDS (Error Detection Sequential), TMA/DSC (Thermal Mechanical Analysis/Differential Scanning Calorimetry) etc.

Thermo-mechanical reliability studies of lead-free solder interconnects

N/ASolder interconnections, also known as solder joints, are the weakest link in electronics packaging. Reliability of these miniature joints is of utmost interest - especially in safety-critical applications in the automotive, medical, aerospace, power grid and oil and drilling sectors. Studies have shown that these joints' critical thermal and mechanical loading culminate in accelerated creep, fatigue, and a combination of these joints' induced failures. The ball grid array (BGA) components being an integral part of many electronic modules functioning in mission-critical systems. This study investigates the response of solder joints in BGA to crucial reliability influencing parameters derived from creep, visco-plastic and fatigue damage of the joints. These are the plastic strain, shear strain, plastic shear strain, creep energy density, strain energy density, deformation, equivalent (Von-Mises) stress etc. The parameters' obtained magnitudes are inputted into established life prediction models – Coffin-Manson, Engelmaier, Solomon (Low cycle fatigue) and Syed (Accumulated creep energy density) – to determine several BGA assemblies' fatigue lives. The joints are subjected to thermal, mechanical and random vibration loadings. The finite element analysis (FEA) is employed in a commercial software package to model and simulate the responses of the solder joints of the representative assemblies' finite element models. As the magnitude and rate of degradation of solder joints in the BGA significantly depend on the composition of the solder alloys used to assembly the BGA on the printed circuit board, this research studies the response of various mainstream lead-free Sn-Ag-Cu (SAC) solders (SAC305, SAC387, SAC396 and SAC405) and benchmarked those with lead-based eutectic solder (Sn63Pb37). In the creep response study, the effects of thermal ageing and temperature cycling on these solder alloys' behaviours are explored. The results show superior creep properties for SAC405 and SAC396 lead-free solder alloys. The lead-free SAC405 solder joint is the most effective solder under thermal cycling condition, and the SAC396 solder joint is the most effective solder under isothermal ageing operation. The finding shows that SAC405 and SAC396 solders accumulated the minimum magnitudes of stress, strain rate, deformation rate and strain energy density than any other solder considered in this study. The hysteresis loops show that lead-free SAC405 has the lowest dissipated energy per cycle. Thus the highest fatigue life, followed by eutectic lead-based Sn63Pb37 solder. The solder with the highest dissipated energy per cycle was lead-free SAC305, SAC387 and SAC396 solder alloys. In the thermal fatigue life prediction research, four different lead-free (SAC305, SAC387, SAC396 and SAC405) and one eutectic lead-based (Sn63Pb37) solder alloys are defined against their thermal fatigue lives (TFLs) to predict their mean-time-to-failure for preventive maintenance advice. Five finite elements (FE) models of the assemblies of the BGAs with the different solder alloy compositions and properties are created with SolidWorks. The models are subjected to standard IEC 60749-25 temperature cycling in ANSYS 19.0 mechanical package environment. SAC405 joints have the highest predicted TFL of circa 13.2 years, while SAC387 joints have the least life of circa 1.4 years. The predicted lives are inversely proportional to the magnitude of the areas of stress-strain hysteresis loops of the solder joints. The prediction models are significantly consistent in predicted magnitudes across the solder joints irrespective of the damage parameters used. Several failure modes drive solder joints and damage mechanics from the research and understand an essential variation in the models' predicted values. This investigation presents a method of managing preventive maintenance time of BGA electronic components in mission-critical systems. It recommends developing a novel life prediction model based on a combination of the damage parameters for enhanced prediction. The FEA random vibration simulation test results showed that different solder alloys have a comparable performance during random vibration testing. The fatigue life result shows that SAC405 and SAC396 have the highest fatigue lives before being prone to failure. As a result of the FEA simulation outcomes with the application of Coffin-Manson's empirical formula, the author can predict the fatigue life of solder joint alloys to a higher degree of accuracy of average ~93% in an actual service environment such as the one experienced under-the-hood of an automobile and aerospace. Therefore, it is concluded that the combination of FEA simulation and empirical formulas employed in this study could be used in the computation and prediction of the fatigue life of solder joint alloys when subjected to random vibration. Based on the thermal and mechanical responses of lead-free SAC405 and SAC396 solder alloys, they are recommended as a suitable replacement of lead-based eutectic Sn63Pb37 solder alloy for improved device thermo-mechanical operations when subjected to random vibration (non-deterministic vibration). The FEA simulation studies' outcomes are validated using experimental and analytical-based reviews in published and peer-reviewed literature.N/

Optimization for finite element modeling of electronic components under dynamic loaDing

Usage of electronic components in the U.S. ARMY applications is becoming more challenging due to their usage in harsh environments. Experimental verification of these components is expensive and it can yield information about specific locations only. This research outlines the finite element modeling methodology for these electronic components that are subjected to high acceleration loads that occur over extremely short time such as impact, gun firing and blast events. Due to their miniature size these finite element models are computationally expensive. An optimization engine was presented to have an efficient analysis procedure that provides a combination of accuracy, computational speed and modeling simplicity. This research also involves experimental testing of the electronic components mounted on the circuit boards. Testing was conducted at different strain levels in order to study the behavior of boards. Finite element models were developed for these tests and compared with experimental results

On the Life Prediction and Accelerated Testing of Solder Joints”,

Abstrac

Properties and behaviour of Pb-free solders in flip-chip scale solder interconnections

Due to pending legislations and market pressure, lead-free solders will replace Sn–Pb solders in 2006. Among the lead-free solders being studied, eutectic Sn–Ag, Sn–Cu and Sn–Ag–Cu are promising candidates and Sn–3.8Ag–0.7Cu could be the most appropriate replacement due to its overall balance of properties. In order to garner more understanding of lead-free solders and their application in flip-chip scale packages, the properties of lead free solders, including the wettability, intermetallic compound (IMC) growth and distribution, mechanical properties, reliability and corrosion resistance, were studied and are presented in this thesis. [Continues.

Reliability assessment of telecommunications equipment

This thesis studies the reliability of telecommunications equipment, its components, and the systems made using those components. Special attention is paid to creating stronger links between the reliability analyses performed at different hierarchy levels. The thesis starts with a temperature derating study. It is found out that the generic handbook based procedures may not always be very attractive, as they do not take satisfactorily into account the actual lifetime requirements. An alternative approach is proposed as a remedy to the current situation. Thermal cycling requirement handbooks are surveyed, and based on the findings some enhancements are proposed. Next, a component and product specific approach to create thermal cycling requirements is suggested. When applying the new approach several factors can be taken into account: the product's lifetime requirement, the field environment, the reliability test result, and the statistical distribution of the component population. A new method of how to predict the reliability of a component population that is addressed to several, different field environments is presented. Ceramic, leadless components are studied by testing and by utilizing Engelmaier's analytical solder fatigue model and Finite Element (FE) simulations. A new approach to interpret the solder joint height in conjunction with solder castellations is introduced. Based on this, a very good correlation between the test results and the predictions based on Engelmaier's model can be obtained. The parameter sensitivity of both the Engelmaier's model and the FE analysis are studied and compared. Error margins based on the parameter sensitivity studies are given. Time-averaged hazard rate functions are studied in order to be able to use component level test data in simplistic parts-count method type reliability predictions. Finally, the availability of a full 3rd generation telecommunications network is studied.reviewe