An FPGA Architecture and CAD Flow Supporting Dynamically Controlled Power Gating

© 2015 IEEE.Leakage power is an important component of the total power consumption in field-programmable gate arrays (FPGAs) built using 90-nm and smaller technology nodes. Power gating was shown to be effective at reducing the leakage power. Previous techniques focus on turning OFF unused FPGA resources at configuration time; the benefit of this approach depends on resource utilization. In this paper, we present an FPGA architecture that enables dynamically controlled power gating, in which FPGA resources can be selectively powered down at run-time. This could lead to significant overall energy savings for applications having modules with long idle times. We also present a CAD flow that can be used to map applications to the proposed architecture. We study the area and power tradeoffs by varying the different FPGA architecture parameters and power gating granularity. The proposed CAD flow is used to map a set of benchmark circuits that have multiple power-gated modules to the proposed architecture. Power savings of up to 83% are achievable for these circuits. Finally, we study a control system of a robot that is used in endoscopy. Using the proposed architecture combined with clock gating results in up to 19% energy savings in this application

Power Efficient Data-Aware SRAM Cell for SRAM-Based FPGA Architecture

The design of low-power SRAM cell becomes a necessity in today\u27s FPGAs, because SRAM is a critical component in FPGA design and consumes a large fraction of the total power. The present chapter provides an overview of various factors responsible for power consumption in FPGA and discusses the design techniques of low-power SRAM-based FPGA at system level, device level, and architecture levels. Finally, the chapter proposes a data-aware dynamic SRAM cell to control the power consumption in the cell. Stack effect has been adopted in the design to reduce the leakage current. The various peripheral circuits like address decoder circuit, write/read enable circuits, and sense amplifier have been modified to implement a power-efficient SRAM-based FPGA

A Low-Voltage, Low-Power 4-bit BCD Adder, designed using the Clock Gated Power Gating, and the DVT Scheme

This paper proposes a Low-Power, Energy Efficient 4-bit Binary Coded Decimal (BCD) adder design where the conventional 4-bit BCD adder has been modified with the Clock Gated Power Gating Technique. Moreover, the concept of DVT (Dual-vth) scheme has been introduced while designing the full adder blocks to reduce the Leakage Power, as well as, to maintain the overall performance of the entire circuit. The reported architecture of 4-bit BCD adder is designed using 45 nm technology and it consumes 1.384 {\mu}Watt of Average Power while operating with a frequency of 200 MHz, and a Supply Voltage (Vdd) of 1 Volt. The results obtained from different simulation runs on SPICE, indicate the superiority of the proposed design compared to the conventional 4-bit BCD adder. Considering the product of Average Power and Delay, for the operating frequency of 200 MHz, a fair 47.41 % reduction compared to the conventional design has been achieved with this proposed scheme.Comment: To appear in the proceedings of 2013 IEEE International Conference on Signal Processing, Computing and Control (ISPCC,13

Addressing On-Chip Power Conversion and Dissipation Issues in Many-Core System-on-a-Chip based on Conventional Silicon and Emerging Nanotechnologies

Title from PDF of title page viewed August 27, 2018Dissertation advisor: Masud H ChowdhuryVitaIncludes bibliographical references (pages 158-163)Thesis (Ph.D.)--School of Computing and Engineering and Department of Physics and Astronomy. University of Missouri--Kansas City, 2017Integrated circuits (ICs) are moving towards system-on-a-chip (SOC) designs. SOC allows various small and large electronic systems to be implemented in a single chip. This approach enables the miniaturization of design blocks that leads to high density transistor integration, faster response time, and lower fabrication costs. To reap the benefits of SOC and uphold the miniaturization of transistors, innovative power delivery and power dissipation management schemes are paramount. This dissertation focuses on on-chip integration of power delivery systems and managing power dissipation to increase the lifetime of energy storage elements. We explore this problem from two different angels: On-chip voltage regulators and power gating techniques. On-chip voltage regulators reduce parasitic effects, and allow faster and efficient power delivery for microprocessors. Power gating techniques, on the other hand, reduce the power loss incurred by circuit blocks during standby mode. Power dissipation (Ptotal = Pstatic and Pdynamic) in a complementary metal-oxide semiconductor (CMOS) circuit comes from two sources: static and dynamic. A quadratic dependency on the dynamic switching power and a more than linear dependency on static power as a form of gate leakage (subthreshold current) exist. To reduce dynamic power loss, the supply power should be reduced. A significant reduction in power dissipation occurs when portions of a microprocessor operate at a lower voltage level. This reduction in supply voltage is achieved via voltage regulators or converters. Voltage regulators are used to provide a stable power supply to the microprocessor. The conventional off-chip switching voltage regulator contains a passive floating inductor, which is difficult to be implemented inside the chip due to excessive power dissipation and parasitic effects. Additionally, the inductor takes a very large chip area while hampering the scaling process. These limitations make passive inductor based on-chip regulator design very unattractive for SOC integration and multi-/many-core environments. To circumvent the challenges, three alternative techniques based on active circuit elements to replace the passive LC filter of the buck convertor are developed. The first inductorless on-chip switching voltage regulator architecture is based on a cascaded 2nd order multiple feedback (MFB) low-pass filter (LPF). This design has the ability to modulate to multiple voltage settings via pulse with modulation (PWM). The second approach is a supplementary design utilizing a hybrid low drop-out scheme to lower the output ripple of the switching regulator over a wider frequency range. The third design approach allows the integration of an entire power management system within a single chipset by combining a highly efficient switching regulator with an intermittently efficient linear regulator (area efficient), for robust and highly efficient on-chip regulation. The static power (Pstatic) or subthreshold leakage power (Pleak) increases with technology scaling. To mitigate static power dissipation, power gating techniques are implemented. Power gating is one of the popular methods to manage leakage power during standby periods in low-power high-speed IC design. It works by using transistor based switches to shut down part of the circuit block and put them in the idle mode. The efficiency of a power gating scheme involves minimum Ioff and high Ion for the sleep transistor. A conventional sleep transistor circuit design requires an additional header, footer, or both switches to turn off the logic block. This additional transistor causes signal delay and increases the chip area. We propose two innovative designs for next generation sleep transistor designs. For an above threshold operation, we present a sleep transistor design based on fully depleted silicon-on-insulator (FDSOI) device. For a subthreshold circuit operation, we implement a sleep transistor utilizing the newly developed silicon-on ferroelectric-insulator field effect transistor (SOFFET). In both of the designs, the ability to control the threshold voltage via bias voltage at the back gate makes both devices more flexible for sleep transistors design than a bulk MOSFET. The proposed approaches simplify the design complexity, reduce the chip area, eliminate the voltage drop by sleep transistor, and improve power dissipation. In addition, the design provides a dynamically controlled Vt for times when the circuit needs to be in a sleep or switching mode.Introduction -- Background and literature review -- Fully integrated on-chip switching voltage regulator -- Hybrid LDO voltage regulator based on cascaded second order multiple feedback loop -- Single and dual output two-stage on-chip power management system -- Sleep transistor design using double-gate FDSOI -- Subthreshold region sleep transistor design -- Conclusio

An Ultra-Low-Energy, Variation-Tolerant FPGA Architecture Using Component-Specific Mapping

As feature sizes scale toward atomic limits, parameter variation continues to increase, leading to increased margins in both delay and energy. Parameter variation both slows down devices and causes devices to fail. For applications that require high performance, the possibility of very slow devices on critical paths forces designers to reduce clock speed in order to meet timing. For an important and emerging class of applications that target energy-minimal operation at the cost of delay, the impact of variation-induced defects at very low voltages mandates the sizing up of transistors and operation at higher voltages to maintain functionality. With post-fabrication configurability, FPGAs have the opportunity to self-measure the impact of variation, determining the speed and functionality of each individual resource. Given that information, a delay-aware router can use slow devices on non-critical paths, fast devices on critical paths, and avoid known defects. By mapping each component individually and customizing designs to a component's unique physical characteristics, we demonstrate that we can eliminate delay margins and reduce energy margins caused by variation. To quantify the potential benefit we might gain from component-specific mapping, we first measure the margins associated with parameter variation, and then focus primarily on the energy benefits of FPGA delay-aware routing over a wide range of predictive technologies (45 nm--12 nm) for the Toronto20 benchmark set. We show that relative to delay-oblivious routing, delay-aware routing without any significant optimizations can reduce minimum energy/operation by 1.72x at 22 nm. We demonstrate how to construct an FPGA architecture specifically tailored to further increase the minimum energy savings of component-specific mapping by using the following techniques: power gating, gate sizing, interconnect sparing, and LUT remapping. With all optimizations considered we show a minimum energy/operation savings of 2.66x at 22 nm, or 1.68--2.95x when considered across 45--12 nm. As there are many challenges to measuring resource delays and mapping per chip, we discuss methods that may make component-specific mapping more practical. We demonstrate that a simpler, defect-aware routing achieves 70% of the energy savings of delay-aware routing. Finally, we show that without variation tolerance, scaling from 16 nm to 12 nm results in a net increase in minimum energy/operation; component-specific mapping, however, can extend minimum energy/operation scaling to 12 nm and possibly beyond.</p

Voltage and Timing Adaptation for Variation and Aging Tolerance in Nanometer VLSI Circuits

Process variations and circuit aging continue to be main challenges to the power-efficiency of VLSI circuits, as considerable power budget must be allocated at design time to mitigate timing variations. Modern designs incorporate adaptive techniques for variation compensation to reduce the extra power consumption. The efficiency of existing adaptive approaches, however, is often significantly attenuated by the fine-grained nature of variations in nanometer technology such as random dopant fluctuation, litho-variation, and different rates of transistor degradation due to non-uniform activity factors. This dissertation addresses the limitations from existing adaptation techniques, and proposes new adaptive approaches to effectively compensate the fine-grained variations. Adaptive supply voltage (ASV) is one of the effective adaptation approaches for power-performance tuning. ASV has advantages on controlling dynamic and leakage power, while voltage generation and delivery overheads from conventional ASV systems make their application to mitigate fine-grained variations demanding. This dissertation presents a dual-level ASV system which provides ASV at both coarse-grained and fine-grained level, and has limited power routing overhead. Significant power reduction from our dual-ASV system demonstrates its superiority over existing approaches. Another novel technique on supply voltage adaptation for variation resilience in VLSI interconnects is proposed. A programmable boostable repeater design boosts switching speed by raising its internal voltage rail transiently and autonomously, and achieves fine-grained voltage adaptation without stand-alone voltage regulators or additional power grid. Since interconnect is a widely recognized bottleneck to chip performance and tremendous repeaters are employed on chip designs, boostable repeater has plenty of chances to improve system robustness. A low cost scheme for delay variation detection is essential to compose an efficient adaptation system. This dissertation presents an area-efficient built-in delay testing scheme which exploits BIST SCAN architecture and dynamic clock skew control. Using this built-in delay testing scheme, a fine-grained adaptation system composed of the proposed boostable repeater design and adaptive clock skew control is proposed, and demonstrated to mitigate process variation and aging induced timing degradations in a power as well as area efficient manner

Design and Analysis of an Asynchronous Microcontroller

This dissertation presents the design of the most complex MTNCL circuit to date. A fully functional MTNCL MSP430 microcontroller is designed and benchmarked against an open source synchronous MSP430. The designs are compared in terms of area, active energy, and leakage energy. Techniques to reduce MTNCL pipeline activity and improve MTNCL register file area and power consumption are introduced. The results show the MTNCL design to have superior leakage power characteristics. The area and active energy comparisons highlight the need for better MTNCL logic synthesis techniques