Robotic Functional Gait Rehabilitation with Tethered Pelvic Assist Device

The primary goal of human locomotion is to stably translate the center of mass (CoM) over the ground with minimum expenditure of energy. Pelvic movement is crucial for walking because the human CoM is located close to the pelvic center. Because of this anatomical feature, pelvic motion directly contributes to the metabolic expenditure, as well as in the balance to keep the center of mass between the legs. An abnormal pelvic motion during the gait not only causes overexertion, but also adversely affects the motion of the trunk and lower limbs. In order to study different interventions, recently a cable-actuated robotic system called Tethered Pelvic Assist Device (TPAD) was developed at ROAR laboratory at Columbia University. The cable-actuated system has a distinct advantage of applying three dimensional forces on the pelvis at discrete points in the gait cycle in contrast to rigid exoskeletons that restrict natural pelvic motion and add extra inertia from the rigid linkages. However, in order to effectively use TPAD for rehabilitation purposes, we still need to have a better understanding of how human gait is affected by different forces applied by TPAD on the pelvis. In the present dissertation, three different control methodologies for TPAD are discussed by performing human experiments with healthy subjects and patients with gait deficits. Moreover, the corresponding changes in the biomechanics during TPAD training are studied to understand how TPAD mechanistically influences the quality of the human gait. In Chapter 2, an ‘assist-as-needed’ controller is implemented to guide and correct the pelvic motion in three dimensions. Here, TPAD applies the correction force based on the deviation of the current position of the pelvic center from a pre-defined target trajectory. This force acts on the pelvic center to guide it towards the target trajectory. A subject in the device experiences a force field, where the magnitude becomes larger when the subject deviates further away from the target trajectory. This control strategy is tested by performing the experiments on healthy subjects with different target pelvic trajectories. Chapter 3 describes a robotic resistive training study using a continuous force on the pelvis to strengthen the weak limbs so that subjects can improve their walking. This study is designed to improve the abnormal gait of children with Cerebral Palsy (CP) who have a crouch gait. Crouch gait is caused by a combination of weak extensor muscles that do not produce adequate muscle forces to keep the posture upright, coupled with contraction of muscles that limit the joint range of motion. Among the extensor muscles, the soleus muscle acts as the major weight-bearing muscle to prevent the knees from collapsing forward during the middle of the stance phase when the foot is on the ground. Electromyography, kinematics, and clinical measurements of the patients with crouch gait show significant improvements in the gait quality after the resistive TPAD training performed over five weeks. Both Chapters 2 & 3 present interventions that are bilaterally applied on both legs. Chapter 4 introduces a training strategy that can be used for patients who have impairments in only one leg which results in manifests as asymmetric weight-bearing while walking. This training method is designed to improve the asymmetric weight bearing of the hemiparetic patients who overly rely on the stronger leg. The feasibility of this training method is tested by experiments with healthy subjects, where the controller creates an asymmetric force field to bring asymmetry in weight bearing during walking. In summary, the present dissertation is devoted to developing new training methods that utilize TPAD for rehabilitation purposes and characterize the responses of different force interventions by investigating the resulting biomechanics. We believe that these methodologies with TPAD can be used to improve abnormal gait patterns that are often observed in cerebral palsy or stroke patients

ReHand - a portable assistive rehabilitation hand exoskeleton

This dissertation presents a synthesis of a novel underactuated exoskeleton (namely ReHand2) thought and designed for a task-oriented rehabilitation and/or for empower the human hand. The first part of this dissertation shows the current context about the robotic rehabilitation with a focus on hand pathologies, which influence the hand capability. The chapter is concluded with the presentation of ReHand2. The second chapter describes the human hand biomechanics. Starting from the definition of human hand anatomy, passing through anthropometric data, to taxonomy on hand grasps and finger constraints, both from static and dynamic point of view. In addition, some information about the hand capability are given. The third chapter analyze the current state of the art in hand exoskeleton for rehabilitation and empower tasks. In particular, the chapter presents exoskeleton technologies, from mechanisms to sensors, passing though transmission and actuators. Finally, the current state of the art in terms of prototype and commercial products is presented. The fourth chapter introduces the concepts of underactuation with the basic explanation and the classical notation used typically in the prosthetic field. In addition, the chapter describe also the most used differential elements in the prosthetic, follow by a statical analysis. Moreover typical transmission tree at inter-finger level as well as the intra- finger underactuation are explained . The fifth chapter presents the prototype called ReHand summarizing the device description and explanation of the working principle. It describes also the kinetostatic analysis for both, inter- and the intra-finger modules. in the last section preliminary results obtained with the exoskeleton are shown and discussed, attention is pointed out on prototype’s problems that have carry out at the second version of the device. The sixth chapter describes the evolution of ReHand, describing the kinematics and dynamics behaviors. In particular, for the mathematical description is introduced the notation used in order to analyze and optimize the geometry of the entire device. The introduced model is also implemented in Matlab Simulink environment. Finally, the chapter presents the new features. The seventh chapter describes the test bench and the methodologies used to evaluate the device statical, and dynamical performances. The chapter presents and discuss the experimental results and compare them with simulated one. Finally in the last chapter the conclusion about the ReHand project are proposed as well as the future development. In particular, the idea to test de device in relevant environments. In addition some preliminary considerations about the thumb and the wrist are introduced, exploiting the possibility to modify the entire layout of the device, for instance changing the actuator location

ANKLE IMPEDANCE AND ANKLE ANGLES DURING STEP TURN AND STRAIGHT WALK: IMPLICATIONS FOR THE DESIGN OF A STEERABLE ANKLE-FOOT PROSTHETIC ROBOT

During locomotion, turning is a common and recurring event which is largely neglected in the current state-of-the-art ankle-foot prostheses, forcing amputees to use different steering mechanisms for turning, compared to non-amputees. A better understanding of the complexities surrounding lower limb prostheses will lead to increased health and well-being of amputees. The aim of this research is to develop a steerable ankle-foot prosthesis that mimics the human ankle mechanical properties. Experiments were developed to estimate the mechanical impedance of the ankle and the ankles angles during straight walk and step turn. Next, this information was used in the design of a prototype, powered steerable ankle-foot prosthesis with two controllable degrees of freedom. One of the possible approaches in design of the prosthetic robots is to use the human joints’ parameters, especially their impedance. A series of experiments were conducted to estimate the stochastic mechanical impedance of the human ankle when muscles were fully relaxed and co-contracting antagonistically. A rehabilitation robot for the ankle, Anklebot, was employed to provide torque perturbations to the ankle. The experiments were performed in two different configurations, one with relaxed muscles, and one with 10% of maximum voluntary contraction (MVC). Surface electromyography (sEMG) was used to monitor muscle activation levels and these sEMG signals were displayed to subjects who attempted to maintain them constant. Time histories of ankle torques and angles in the lateral/medial (LM) directions, inversion-eversion (IE), and dorsiflexionplantarflexion (DP) were recorded. Linear time-invariant transfer functions between the measured torques and angles were estimated providing an estimate of ankle mechanical impedance. High coherence was observed over a frequency range up to 30 Hz. The main effect of muscle activation was to increase the magnitude of ankle mechanical impedance in all degrees of freedom of the ankle. Another experiment compared the three-dimensional angles of the ankle during step turn and straight walking. These angles were measured to be used for developing the control strategy of the ankle-foot prosthesis. An infrared camera system was used to track the trajectories and angles of the foot and leg. The combined phases of heel strike and loading response, mid stance, and terminal stance and pre-swing were determined and used to measure the average angles at each combined phase. The Range of motion (ROM) in IE increased during turning while ML rotation decreased and DP changed the least. During the turning step, ankle displacement in DP started with similar angles to straight walk and progressively showed less plantarflexion. In IE, the ankle showed increased inversion leaning the body toward the inside of the turn. ML rotation initiated with an increased medial rotation during the step turn relative to the straight walk transitioning to increased lateral rotation at the toe off. A prototype ankle-foot prosthesis capable of controlling both DP and IE using a cable driven mechanism was developed and assessed as part of a feasibility study. The design is capable of reproducing the angles required for straight walk and step turn; generates 712N of lifting force in plantarflexion, and shows passive stiffness comparable to a nonload bearing ankle impedance. To evaluate the performance of the ankle-foot prosthesis, a circular treadmill was developed to mimic human gait during steering. Preliminary results show that the device can appropriately simulate human gait with loading and unloading the ankle joint during the gait in circular paths

A Series-Elastic Robot for Back-Pain Rehabilitation

Robotics research has been broadly expanding into various fields during the past decades. It is widely spread and best known for solving many technical necessities in different fields. With the rise of the industrial revolution, it upgraded many factories to use industrial robots to prevent the human operator from dangerous and hazardous tasks. The rapid development of application fields and their complexity have inspired researchers in the robotics community to find innovative solutions to meet the new desired requirements of the field. Currently, the creation of new needs outside the traditional industrial robots are demanding robots to attend to the new market and to assist humans in meeting their daily social needs (i.e., agriculture, construction, cleaning.). The future integration of robots into other types of production processes, added new requirements that require more safety, flexibility, and intelligence in robots. Areas of robotics has evolved into various fields. This dissertation addresses robotics research in four different areas: rehabilitation robots, biologically inspired robots, optimization techniques, and neural network implementation. Although these four areas may seem different from each other, they share some research topics and applications