Low-Power Embedded Design Solutions and Low-Latency On-Chip Interconnect Architecture for System-On-Chip Design

This dissertation presents three design solutions to support several key system-on-chip (SoC) issues to achieve low-power and high performance. These are: 1) joint source and channel decoding (JSCD) schemes for low-power SoCs used in portable multimedia systems, 2) efficient on-chip interconnect architecture for massive multimedia data streaming on multiprocessor SoCs (MPSoCs), and 3) data processing architecture for low-power SoCs in distributed sensor network (DSS) systems and its implementation. The first part includes a low-power embedded low density parity check code (LDPC) - H.264 joint decoding architecture to lower the baseband energy consumption of a channel decoder using joint source decoding and dynamic voltage and frequency scaling (DVFS). A low-power multiple-input multiple-output (MIMO) and H.264 video joint detector/decoder design that minimizes energy for portable, wireless embedded systems is also designed. In the second part, a link-level quality of service (QoS) scheme using unequal error protection (UEP) for low-power network-on-chip (NoC) and low latency on-chip network designs for MPSoCs is proposed. This part contains WaveSync, a low-latency focused network-on-chip architecture for globally-asynchronous locally-synchronous (GALS) designs and a simultaneous dual-path routing (SDPR) scheme utilizing path diversity present in typical mesh topology network-on-chips. SDPR is akin to having a higher link width but without the significant hardware overhead associated with simple bus width scaling. The last part shows data processing unit designs for embedded SoCs. We propose a data processing and control logic design for a new radiation detection sensor system generating data at or above Peta-bits-per-second level. Implementation results show that the intended clock rate is achieved within the power target of less than 200mW. We also present a digital signal processing (DSP) accelerator supporting configurable MAC, FFT, FIR, and 3-D cross product operations for embedded SoCs. It consumes 12.35mW along with 0.167mm2 area at 333MHz

Optimisation énergétique de processus de traitement du signal et ses applications au décodage vidéo

Consumer electronics offer today more and more features (video, audio, GPS, Internet) and connectivity means (multi-radio systems with WiFi, Bluetooth, UMTS, HSPA, LTE-advanced ... ). The power demand of these devices is growing for the digital part especially for the processing chip. To support this ever increasing computing demand, processor architectures have evolved with multicore processors, graphics processors (GPU) and ether dedicated hardware accelerators. However, the evolution of battery technology is itself slower. Therefore, the autonomy of embedded systems is now under a great pressure. Among the new functionalities supported by mobile devices, video services take a prominent place. lndeed, recent analyzes show that they will represent 70% of mobile Internet traffic by 2016. Accompanying this growth, new technologies are emerging for new services and applications. Among them HEVC (High Efficiency Video Coding) can double the data compression while maintaining a subjective quality equivalent to its predecessor, the H.264 standard. ln a digital circuit, the total power consumption is made of static power and dynamic power. Most of modern hardware architectures implement means to control the power consumption of the system. Dynamic Voltage and Frequency Scaling (DVFS) mainly reduces the dynamic power of the circuit. This technique aims to adapt the power of the processor (and therefore its consumption) to the actual load needed by the application. To control the static power, Dynamic Power Management (DPM or sleep modes) aims to stop the voltage supplies associated with specific areas of the chip. ln this thesis, we first present a model of the energy consumed by the circuit integrating DPM and DVFS modes. This model is generalized to multi-core integrated circuits and to a rapid prototyping tool. Thus, the optimal operating point of a circuit, i.e. the operating frequency and the number of active cores, is identified. Secondly, the HEVC application is integrated to a multicore architecture coupled with a sophisticated DVFS mechanism. We show that this application can be implemented efficiently on general purpose processors (GPP) while minimizing the power consumption. Finally, and to get further energy gain, we propose a modified HEVC decoder that is capable to tune its energy gains together with a decoding quality trade-off.Aujourd'hui, les appareils électroniques offrent de plus en plus de fonctionnalités (vidéo, audio, GPS, internet) et des connectivités variées (multi-systèmes de radio avec WiFi, Bluetooth, UMTS, HSPA, LTE-advanced ... ). La demande en puissance de ces appareils est donc grandissante pour la partie numérique et notamment le processeur de calcul. Pour répondre à ce besoin sans cesse croissant de nouvelles fonctionnalités et donc de puissance de calcul, les architectures des processeurs ont beaucoup évolué : processeurs multi-coeurs, processeurs graphiques (GPU) et autres accélérateurs matériels dédiés. Cependant, alors que de nouvelles architectures matérielles peinent à répondre aux exigences de performance, l'évolution de la technologie des batteries est quant à elle encore plus lente. En conséquence, l'autonomie des systèmes embarqués est aujourd'hui sous pression. Parmi les nouveaux services supportés par les terminaux mobiles, la vidéo prend une place prépondérante. En effet, des analyses récentes de tendance montrent qu'elle représentera 70 % du trafic internet mobile dès 2016. Accompagnant cette croissance, de nouvelles technologies émergent permettant de nouveaux services et applications. Parmi elles, HEVC (High Efficiency Video Coding) permet de doubler la compression de données tout en garantissant une qualité subjective équivalente à son prédécesseur, la norme H.264. Dans un circuit numérique, la consommation provient de deux éléments: la puissance statique et la puissance dynamique. La plupart des architectures matérielles récentes mettent en oeuvre des procédés permettant de contrôler la puissance du système. Le changement dynamique du couple tension/fréquence appelé Dynamic Voltage and Frequency Scaling (DVFS) agit principalement sur la puissance dynamique du circuit. Cette technique permet d'adapter la puissance du processeur (et donc sa consommation) à la charge réelle nécessaire pour une application. Pour contrôler la puissance statique, le Dynamic Power Management (DPM, ou modes de veille) consistant à arrêter les alimentations associées à des zones spécifiques de la puce. Dans cette thèse, nous présentons d'abord une modélisation de l'énergie consommée par le circuit intégrant les modes DVFS et DPM. Cette modélisation est généralisée au circuit multi-coeurs et intégrée à un outil de prototypage rapide. Ainsi le point de fonctionnement optimal d'un circuit, la fréquence de fonctionnement et le nombre de coeurs actifs, est identifié. Dans un second temps, l'application HEVC est intégrée à une architecture multi-coeurs avec une adaptation dynamique de la fréquence de développement. Nous montrons que cette application peut être implémentée efficacement sur des processeurs généralistes (GPP) tout en minimisant la puissance consommée. Enfin, et pour aller plus loin dans les gains en énergie, nous proposons une modification du décodeur HEVC qui permet à un décodeur de baisser encore plus sa consommation en fonction du budget énergétique disponible localement

Parallel algorithms and architectures for low power video decoding

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2010.Cataloged from PDF version of thesis.Includes bibliographical references (p. 197-204).Parallelism coupled with voltage scaling is an effective approach to achieve high processing performance with low power consumption. This thesis presents parallel architectures and algorithms designed to deliver the power and performance required for current and next generation video coding. Coding efficiency, area cost and scalability are also addressed. First, a low power video decoder is presented for the current state-of-the-art video coding standard H.264/AVC. Parallel architectures are used along with voltage scaling to deliver high definition (HD) decoding at low power levels. Additional architectural optimizations such as reducing memory accesses and multiple frequency/voltage domains are also described. An H.264/AVC Baseline decoder test chip was fabricated in 65-nm CMOS. It can operate at 0.7 V for HD (720p, 30 fps) video decoding and with a measured power of 1.8 mW. The highly scalable decoder can tradeoff power and performance across >100x range. Second, this thesis demonstrates how serial algorithms, such as Context-based Adaptive Binary Arithmetic Coding (CABAC), can be redesigned for parallel architectures to enable high throughput with low coding efficiency cost. A parallel algorithm called the Massively Parallel CABAC (MP-CABAC) is presented that uses syntax element partitions and interleaved entropy slices to achieve better throughput-coding efficiency and throughput-area tradeoffs than H.264/AVC. The parallel algorithm also improves scalability by providing a third dimension to tradeoff coding efficiency for power and performance. Finally, joint algorithm-architecture optimizations are used to increase performance and reduce area with almost no coding penalty. The MP-CABAC is mapped to a highly parallel architecture with 80 parallel engines, which together delivers >10x higher throughput than existing H.264/AVC CABAC implementations. A MP-CABAC test chip was fabricated in 65-nm CMOS to demonstrate the power-performance-coding efficiency tradeoff.by Vivienne. Sze.Ph.D

An efficient design space exploration framework to optimize power-efficient heterogeneous many-core multi-threading embedded processor architectures

By the middle of this decade, uniprocessor architecture performance had hit a roadblock due to a combination of factors, such as excessive power dissipation due to high operating frequencies, growing memory access latencies, diminishing returns on deeper instruction pipelines, and a saturation of available instruction level parallelism in applications. An attractive and viable alternative embraced by all the processor vendors was multi-core architectures where throughput is improved by using micro-architectural features such as multiple processor cores, interconnects and low latency shared caches integrated on a single chip. The individual cores are often simpler than uniprocessor counterparts, use hardware multi-threading to exploit thread-level parallelism and latency hiding and typically achieve better performance-power figures. The overwhelming success of the multi-core microprocessors in both high performance and embedded computing platforms motivated chip architects to dramatically scale the multi-core processors to many-cores which will include hundreds of cores on-chip to further improve throughput. With such complex large scale architectures however, several key design issues need to be addressed. First, a wide range of micro- architectural parameters such as L1 caches, load/store queues, shared cache structures and interconnection topologies and non-linear interactions between them define a vast non-linear multi-variate micro-architectural design space of many-core processors; the traditional method of using extensive in-loop simulation to explore the design space is simply not practical. Second, to accurately evaluate the performance (measured in terms of cycles per instruction (CPI)) of a candidate design, the contention at the shared cache must be accounted in addition to cycle-by-cycle behavior of the large number of cores which superlinearly increases the number of simulation cycles per iteration of the design exploration. Third, single thread performance does not scale linearly with number of hardware threads per core and number of cores due to memory wall effect. This means that at every step of the design process designers must ensure that single thread performance is not unacceptably slowed down while increasing overall throughput. While all these factors affect design decisions in both high performance and embedded many-core processors, the design of embedded processors required for complex embedded applications such as networking, smart power grids, battlefield decision-making, consumer electronics and biomedical devices to name a few, is fundamentally different from its high performance counterpart because of the need to consider (i) low power and (ii) real-time operations. This implies the design objective for embedded many-core processors cannot be to simply maximize performance, but improve it in such a way that overall power dissipation is minimized and all real-time constraints are met. This necessitates additional power estimation models right at the design stage to accurately measure the cost and reliability of all the candidate designs during the exploration phase. In this dissertation, a statistical machine learning (SML) based design exploration framework is presented which employs an execution-driven cycle- accurate simulator to accurately measure power and performance of embedded many-core processors. The embedded many-core processor domain is Network Processors (NePs) used to processed network IP packets. Future generation NePs required to operate at terabits per second network speeds captures all the aspects of a complex embedded application consisting of shared data structures, large volume of compute-intensive and data-intensive real-time bound tasks and a high level of task (packet) level parallelism. Statistical machine learning (SML) is used to efficiently model performance and power of candidate designs in terms of wide ranges of micro-architectural parameters. The method inherently minimizes number of in-loop simulations in the exploration framework and also efficiently captures the non-linear interactions between the micro-architectural design parameters. To ensure scalability, the design space is partitioned into (i) core-level micro-architectural parameters to optimize single core architectures subject to the real-time constraints and (ii) shared memory level micro- architectural parameters to explore the shared interconnection network and shared cache memory architectures and achieves overall optimality. The cost function of our exploration algorithm is the total power dissipation which is minimized, subject to the constraints of real-time throughput (as determined from the terabit optical network router line-speed) required in IP packet processing embedded application

Low-power techniques for video decoding

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2009.This electronic version was submitted by the student author. The certified thesis is available in the Institute Archives and Special Collections.Cataloged from student submitted PDF version of thesis.Includes bibliographical references (p. 149-156).The H.264 video coding standard can deliver high compression efficiency at a cost of large complexity and power. The increasing popularity of video capture and playback on portable devices requires that the energy of the video processing be kept to a minimum. This work implements several architecture optimizations that reduce the system power of a high-definition video decoder. In order to decode high resolutions at low voltages and low frequencies, we employ techniques such as pipelining, unit parallelism, multiple cores, and multiple voltage/frequency domains. For example, a 3-core decoder can reduce the required clock frequency by 2.91 x, which enables a power reduction of 61% relative to a full-voltage single-core decoder. To reduce the total memory system power, several caching techniques are demonstrated that can dramatically reduce the off-chip memory bandwidth and power at the cost of increased chip area. A 123 kB data-forwarding cache can reduce the read bandwidth from external memory by 53%, which leads to 44% power savings in the memory reads. To demonstrate these low-power ideas, a H.264/AVC Baseline Level 3.2 decoder ASIC was fabricated in 65 nm CMOS and verified. It operates down to 0.7 V and has a measured power down to 1.8 mW when decoding a high definition 720p video at 30 frames per second, which is over an order of magnitude lower than previously published results.by Daniel Frederic Finchelstein.Ph.D

Performance and power optimizations in chip multiprocessors for throughput-aware computation

The so-called "power (or power density) wall" has caused core frequency (and single-thread performance) to slow down, giving rise to the era of multi-core/multi-thread processors. For example, the IBM POWER4 processor, released in 2001, incorporated two single-thread cores into the same chip. In 2010, IBM released the POWER7 processor with eight 4-thread cores in the same chip, for a total capacity of 32 execution contexts. The ever increasing number of cores and threads gives rise to new opportunities and challenges for software and hardware architects. At software level, applications can benefit from the abundant number of execution contexts to boost throughput. But this challenges programmers to create highly-parallel applications and operating systems capable of scheduling them correctly. At hardware level, the increasing core and thread count puts pressure on the memory interface, because memory bandwidth grows at a slower pace ---phenomenon known as the "bandwidth (or memory) wall". In addition to memory bandwidth issues, chip power consumption rises due to manufacturers' difficulty to lower operating voltages sufficiently every processor generation. This thesis presents innovations to improve bandwidth and power consumption in chip multiprocessors (CMPs) for throughput-aware computation: a bandwidth-optimized last-level cache (LLC), a bandwidth-optimized vector register file, and a power/performance-aware thread placement heuristic. In contrast to state-of-the-art LLC designs, our organization avoids data replication and, hence, does not require keeping data coherent. Instead, the address space is statically distributed all over the LLC (in a fine-grained interleaving fashion). The absence of data replication increases the cache effective capacity, which results in better hit rates and higher bandwidth compared to a coherent LLC. We use double buffering to hide the extra access latency due to the lack of data replication. The proposed vector register file is composed of thousands of registers and organized as an aggregation of banks. We leverage such organization to attach small special-function "local computation elements" (LCEs) to each bank. This approach ---referred to as the "processor-in-regfile" (PIR) strategy--- overcomes the limited number of register file ports. Because each LCE is a SIMD computation element and all of them can proceed concurrently, the PIR strategy constitutes a highly-parallel super-wide-SIMD device (ideal for throughput-aware computation). Finally, we present a heuristic to reduce chip power consumption by dynamically placing software (application) threads across hardware (physical) threads. The heuristic gathers chip-level power and performance information at runtime to infer characteristics of the applications being executed. For example, if an application's threads share data, the heuristic may decide to place them in fewer cores to favor inter-thread data sharing and communication. In such case, the number of active cores decreases, which is a good opportunity to switch off the unused cores to save power. It is increasingly harder to find bulletproof (micro-)architectural solutions for the bandwidth and power scalability limitations in CMPs. Consequently, we think that architects should attack those problems from different flanks simultaneously, with complementary innovations. This thesis contributes with a battery of solutions to alleviate those problems in the context of throughput-aware computation: 1) proposing a bandwidth-optimized LLC; 2) proposing a bandwidth-optimized register file organization; and 3) proposing a simple technique to improve power-performance efficiency.El excesivo consumo de potencia de los procesadores actuales ha desacelerado el incremento en la frecuencia operativa de los mismos para dar lugar a la era de los procesadores con múltiples núcleos y múltiples hilos de ejecución. Por ejemplo, el procesador POWER7 de IBM, lanzado al mercado en 2010, incorpora ocho núcleos en el mismo chip, con cuatro hilos de ejecución por núcleo. Esto da lugar a nuevas oportunidades y desafíos para los arquitectos de software y hardware. A nivel de software, las aplicaciones pueden beneficiarse del abundante número de núcleos e hilos de ejecución para aumentar el rendimiento. Pero esto obliga a los programadores a crear aplicaciones altamente paralelas y sistemas operativos capaces de planificar correctamente la ejecución de las mismas. A nivel de hardware, el creciente número de núcleos e hilos de ejecución ejerce presión sobre la interfaz de memoria, ya que el ancho de banda de memoria crece a un ritmo más lento. Además de los problemas de ancho de banda de memoria, el consumo de energía del chip se eleva debido a la dificultad de los fabricantes para reducir suficientemente los voltajes de operación entre generaciones de procesadores. Esta tesis presenta innovaciones para mejorar el ancho de banda y consumo de energía en procesadores multinúcleo en el ámbito de la computación orientada a rendimiento ("throughput-aware computation"): una memoria caché de último nivel ("last-level cache" o LLC) optimizada para ancho de banda, un banco de registros vectorial optimizado para ancho de banda, y una heurística para planificar la ejecución de aplicaciones paralelas orientada a mejorar la eficiencia del consumo de potencia y desempeño. En contraste con los diseños de LLC de última generación, nuestra organización evita la duplicación de datos y, por tanto, no requiere de técnicas de coherencia. El espacio de direcciones de memoria se distribuye estáticamente en la LLC con un entrelazado de grano fino. La ausencia de replicación de datos aumenta la capacidad efectiva de la memoria caché, lo que se traduce en mejores tasas de acierto y mayor ancho de banda en comparación con una LLC coherente. Utilizamos la técnica de "doble buffering" para ocultar la latencia adicional necesaria para acceder a datos remotos. El banco de registros vectorial propuesto se compone de miles de registros y se organiza como una agregación de bancos. Incorporamos a cada banco una pequeña unidad de cómputo de propósito especial ("local computation element" o LCE). Este enfoque ---que llamamos "computación en banco de registros"--- permite superar el número limitado de puertos en el banco de registros. Debido a que cada LCE es una unidad de cómputo con soporte SIMD ("single instruction, multiple data") y todas ellas pueden proceder de forma concurrente, la estrategia de "computación en banco de registros" constituye un dispositivo SIMD altamente paralelo. Por último, presentamos una heurística para planificar la ejecución de aplicaciones paralelas orientada a reducir el consumo de energía del chip, colocando dinámicamente los hilos de ejecución a nivel de software entre los hilos de ejecución a nivel de hardware. La heurística obtiene, en tiempo de ejecución, información de consumo de potencia y desempeño del chip para inferir las características de las aplicaciones. Por ejemplo, si los hilos de ejecución a nivel de software comparten datos significativamente, la heurística puede decidir colocarlos en un menor número de núcleos para favorecer el intercambio de datos entre ellos. En tal caso, los núcleos no utilizados se pueden apagar para ahorrar energía. Cada vez es más difícil encontrar soluciones de arquitectura "a prueba de balas" para resolver las limitaciones de escalabilidad de los procesadores actuales. En consecuencia, creemos que los arquitectos deben atacar dichos problemas desde diferentes flancos simultáneamente, con innovaciones complementarias

Virtual Runtime Application Partitions for Resource Management in Massively Parallel Architectures

This thesis presents a novel design paradigm, called Virtual Runtime Application Partitions (VRAP), to judiciously utilize the on-chip resources. As the dark silicon era approaches, where the power considerations will allow only a fraction chip to be powered on, judicious resource management will become a key consideration in future designs. Most of the works on resource management treat only the physical components (i.e. computation, communication, and memory blocks) as resources and manipulate the component to application mapping to optimize various parameters (e.g. energy efficiency). To further enhance the optimization potential, in addition to the physical resources we propose to manipulate abstract resources (i.e. voltage/frequency operating point, the fault-tolerance strength, the degree of parallelism, and the configuration architecture). The proposed framework (i.e. VRAP) encapsulates methods, algorithms, and hardware blocks to provide each application with the abstract resources tailored to its needs. To test the efficacy of this concept, we have developed three distinct self adaptive environments: (i) Private Operating Environment (POE), (ii) Private Reliability Environment (PRE), and (iii) Private Configuration Environment (PCE) that collectively ensure that each application meets its deadlines using minimal platform resources. In this work several novel architectural enhancements, algorithms and policies are presented to realize the virtual runtime application partitions efficiently. Considering the future design trends, we have chosen Coarse Grained Reconfigurable Architectures (CGRAs) and Network on Chips (NoCs) to test the feasibility of our approach. Specifically, we have chosen Dynamically Reconfigurable Resource Array (DRRA) and McNoC as the representative CGRA and NoC platforms. The proposed techniques are compared and evaluated using a variety of quantitative experiments. Synthesis and simulation results demonstrate VRAP significantly enhances the energy and power efficiency compared to state of the art.Siirretty Doriast

VLSI Implementation of Low Power Reconfigurable MIMO Detector

Multiple Input Multiple Output (MIMO) systems are a key technology for next generation high speed wireless communication standards like 802.11n, WiMax etc. MIMO enables spatial multiplexing to increase channel bandwidth which requires the use of multiple antennas in the receiver and transmitter side. The increase in bandwidth comes at the cost of high silicon complexity of MIMO detectors which result, due to the intricate algorithms required for the separation of these spatially multiplexed streams. Previous implementations of MIMO detector have mainly dealt with the issue of complexity reduction, latency minimization and throughput enhancement. Although, these detectors have successfully mapped algorithms to relatively simpler circuits but still, latency and throughput of these systems need further improvements to meet standard requirements. Additionally, most of these implementations don’t deal with the requirements of reconfigurability of the detector to multiple modulation schemes and different antennae configurations. This necessary requirement provides another dimension to the implementation of MIMO detector and adds to the implementation complexity. This thesis focuses on the efficient VLSI implementation of the MIMO detector with an emphasis on performance and re-configurability to different modulation schemes. MIMO decoding in our detector is based on the fixed sphere decoding algorithm which has been simplified for an effective VLSI implementation without considerably degrading the near optimal bit error rate performance. The regularity of the architecture makes it suitable for a highly parallel and pipelined implementation. The decoder has intrinsic traits for dynamic re-configurability to different modulation and encoding schemes. This detector architecture can be easily tuned for high/low performance requirements with slight degradation/improvement in Bit Error Rate (BER) depending on needs of the overlying application. Additionally, various architectural optimizations like pipelining, parallel processing, hardware scheduling, dynamic voltage and frequency scaling have been explored to improve the performance, energy requirements and re-configurability of the design

Adaptive Knobs for Resource Efficient Computing

Performance demands of emerging domains such as artificial intelligence, machine learning and vision, Internet-of-things etc., continue to grow. Meeting such requirements on modern multi/many core systems with higher power densities, fixed power and energy budgets, and thermal constraints exacerbates the run-time management challenge. This leaves an open problem on extracting the required performance within the power and energy limits, while also ensuring thermal safety. Existing architectural solutions including asymmetric and heterogeneous cores and custom acceleration improve performance-per-watt in specific design time and static scenarios. However, satisfying applications’ performance requirements under dynamic and unknown workload scenarios subject to varying system dynamics of power, temperature and energy requires intelligent run-time management. Adaptive strategies are necessary for maximizing resource efficiency, considering i) diverse requirements and characteristics of concurrent applications, ii) dynamic workload variation, iii) core-level heterogeneity and iv) power, thermal and energy constraints. This dissertation proposes such adaptive techniques for efficient run-time resource management to maximize performance within fixed budgets under unknown and dynamic workload scenarios. Resource management strategies proposed in this dissertation comprehensively consider application and workload characteristics and variable effect of power actuation on performance for pro-active and appropriate allocation decisions. Specific contributions include i) run-time mapping approach to improve power budgets for higher throughput, ii) thermal aware performance boosting for efficient utilization of power budget and higher performance, iii) approximation as a run-time knob exploiting accuracy performance trade-offs for maximizing performance under power caps at minimal loss of accuracy and iv) co-ordinated approximation for heterogeneous systems through joint actuation of dynamic approximation and power knobs for performance guarantees with minimal power consumption. The approaches presented in this dissertation focus on adapting existing mapping techniques, performance boosting strategies, software and dynamic approximations to meet the performance requirements, simultaneously considering system constraints. The proposed strategies are compared against relevant state-of-the-art run-time management frameworks to qualitatively evaluate their efficacy