ACTIVE NOISE CONTROL USING CARBON NANOTUBE THERMOPHONES: CASE STUDY FOR AN AUTOMOTIVE HVAC APPLICATION

The goal of this project was to reduce the overall noise levels emitted by the HVAC components in a vehicle’s cabin. More specifically, the feasibility of achieving this goal using two key technologies was investigated. The first of these technologies, Active Noise Control (ANC), is a noise attenuation technique that relies on destructive interference that “cancels” unwanted noise. Typically used in situations where physical constraints prevent passive attenuation techniques from being used, ANC is known for its high size-to-effectiveness ratio. This benefit cannot be gained without a cost however; the complexity of ANC systems is significantly higher than their passive counterparts. This is due to the signal processing and actuator designs required. These actuators often take the form of moving-coil loudspeakers which, while effective, are often bulky. Because of this they are difficult to “drop in” to an existing system. This is where the second technology comes in. Carbon Nanotube (CNT) Thermophones are solid-state speakers that operate by using rapid heat fluctuations to create sound. Called the “thermoacoustic effect,” (TE) the theory of this operating principle dates to the turn of the 20th century. Useful demonstration of TE did not occur until 2008, however, when researchers first developed the first CNT thermophones. The hallmark characteristics of these transducers are their small size and flexible nature. Compared to traditional loudspeakers they have a much smaller form factor and are more versatile in terms of where they can be placed in a cramped system. The marriage of CNT transducers to ANC technology shows promise in improving the application space and ease of installation of ANC systems. Getting these two to cooperate, however, is not without challenges. A case study for this union is presented here; the application space being the ducted environment of vehicle HVAC systems

California Extremely Large Telescope: Conceptual Design for a Thirty-Meter Telescope

Following great success in the creation of the Keck Observatory, scientists at the California Institute of Technology and the University of California have begun to explore the scientific and technical prospects for a much larger telescope. The Keck telescopes will remain the largest telescopes in the world for a number of years, with many decades of forefront research ahead after that. Though these telescopes have produced dramatic discoveries, it is already clear that even larger telescopes must be built if we are to address some of the most profound questions about our universe. The time required to build a larger telescope is approximately ten years, and the California community is presently well-positioned to begin its design and construction. The same scientists who conceived, led the design, and guided the construction of the Keck Observatory have been intensely engaged in a study of the prospects for an extremely large telescope. Building on our experience with the Keck Observatory, we have concluded that the large telescope is feasible and is within the bounds set by present-day technology. Our reference telescope has a diameter of 30 meters, the largest size we believe can be built with acceptable risk. The project is currently designated the California Extremely Large Telescope (CELT)

Active control of noise transmitted from barriers

Active noise cancellation is a unique approach that helps passive noise control in reducing sound levels at low frequencies; nevertheless, successful use of active noise cancellation necessitates performing numerous and tedious experiments together with defining several parameters properly. The locations and quantity of active control system transducers are among these parameters. The present research provides a comprehensive framework for placing control sources and error microphones near a noise barrier in order to improve its efficiency in both narrowband and broadband noise spectra. To accomplish this, the appropriate locations for the control sources are first determined using a repetitive computation method, and then the optimizations are completed by determining the best position for the error microphone. Several alternative transducer locations near the barrier are incorporated in the repetitive computation, and the optimal sites for the control sources and error microphones are found using two-step optimization methods as well as the genetic algorithms approach. The findings reveal that the best places to put the control sources are on the incident side, below the barrier's edge, and the best locations to place the error microphones are on the shadow side, as close as possible to the target area. The effect of ground reflection on the efficiency of the active noise control system is also investigated, and it is discovered that while ground reflection has no significant effect on the performance of the active noise control system for broadband frequency ranges, it does reduce the control system's efficiency at tonal noises. In order to optimize more parameters, further calculations are performed based on the genetic optimizer. The output of the GA calculations found new configurations for the control units that result in higher noise level reduction at the target area. In addition to the active noise barrier, the application of active noise cancellation for open windows as a particular case of the barrier is explored as a particular case of the barrier. Different arrangements are studied for the control units close to the open windows, including linear, boundary, and planar control arrangements. The effect of several parameters such as the incident angle of noise waves, the distance between error microphones and the opening, and the number of control units are investigated. The results demonstrate that the active noise control system with obliqued linear placements of transducers have higher performance than the other arrangements. Furthermore, when the frequency and incident angle increase, the effectiveness of active noise reduction decreases.La cancelación activa de ruido es un enfoque único que ayuda al control pasivo del ruido a reducir los niveles de sonido a bajas frecuencias; sin embargo, el uso exitoso de la cancelación activa de ruido requiere la realización de numerosos y tediosos experimentos junto con la definición adecuada de varios parámetros. La ubicación y la cantidad de transductores del sistema de control activo se encuentran entre estos parámetros. La presente investigación proporciona un marco completo para colocar fuentes de control y micrófonos de error cerca de una barrera de ruido con el fin de mejorar su eficiencia en espectros de ruido de banda estrecha y banda ancha. Para lograr esto, primero se determinan las ubicaciones apropiadas para las fuentes de control usando un método de cálculo repetitivo, y luego se completan las optimizaciones determinando la mejor posición para el micrófono de error. Varias ubicaciones de transductores alternativas cerca de la barrera se incorporan en el cálculo repetitivo, y los sitios óptimos para las fuentes de control y los micrófonos de error se encuentran utilizando métodos de optimización de dos pasos, así como el enfoque de algoritmos genéticos. Los hallazgos revelan que los mejores lugares para colocar las fuentes de control están en el lado del incidente, debajo del borde de la barrera, y los mejores lugares para colocar los micrófonos de error están en el lado de la sombra, lo más cerca posible del área objetivo. También se investiga el efecto de la reflexión del suelo sobre la eficiencia del sistema de control de ruido activo, y se descubre que si bien la reflexión del suelo no tiene un efecto significativo en el rendimiento del sistema de control de ruido activo para rangos de frecuencia de banda ancha, sí reduce el rendimiento del sistema de control. eficiencia en ruidos tonales. Para optimizar más parámetros, se realizan más cálculos basadosen el optimizador genético. El resultado de los cálculos de GA encontró nuevas configuraciones para las unidades de control que dan como resultado una mayor reducción del nivel de ruido en el área objetivo. Además de la barrera de ruido activa, se explora la aplicación de la cancelación de ruido activa para ventanas abiertas como un caso particular de la barrera. Se estudian cuatro disposiciones para las unidades de control cercanas a las ventanas abiertas. Las unidades de control en una configuración de límite se colocan en el borde de la abertura, mientras que en el control plano, se ubican en la superficie de la abertura. En una configuración de contorno, las unidades de control se colocan en el borde de la abertura, mientras que en un diseño plano, se colocan en la superficie de la abertura. Se investiga el efecto de varios parámetros como el ángulo de incidencia de las ondas de ruido, la distancia entre los micrófonos de error y la apertura, y el número de unidades de control. Los resultados demuestran que el sistema de control de ruido activo con configuración plana tiene un rendimiento más alto que el control de límites. Además, cuando la frecuencia y el ángulo de incidencia aumentan, la eficacia de la reducción activa del ruido disminuye.Postprint (published version