Timing and Carrier Synchronization in Wireless Communication Systems: A Survey and Classification of Research in the Last 5 Years

Timing and carrier synchronization is a fundamental requirement for any wireless communication system to work properly. Timing synchronization is the process by which a receiver node determines the correct instants of time at which to sample the incoming signal. Carrier synchronization is the process by which a receiver adapts the frequency and phase of its local carrier oscillator with those of the received signal. In this paper, we survey the literature over the last 5 years (2010–2014) and present a comprehensive literature review and classification of the recent research progress in achieving timing and carrier synchronization in single-input single-output (SISO), multiple-input multiple-output (MIMO), cooperative relaying, and multiuser/multicell interference networks. Considering both single-carrier and multi-carrier communication systems, we survey and categorize the timing and carrier synchronization techniques proposed for the different communication systems focusing on the system model assumptions for synchronization, the synchronization challenges, and the state-of-the-art synchronization solutions and their limitations. Finally, we envision some future research directions

Multi-user interference mitigation under limited feedback requirements for WCDMA systems with base station cooperation

One of the techniques that has been recently identified for dealing with multi-user interference (MUI) in future communications systems is base station (BS) cooperation or joint processing. However, perfect MUI cancellation with this technique demands severe synchronization requirements, perfect and global channel state information (CSI), and an increased backhaul and signaling overhead. In this paper, we consider a more realistic layout with the aim of mitigating the MUI, where only local CSI is available at the BSs. Due to synchronization inaccuracies and errors in the channel estimation, the system becomes partially asynchronous. In the downlink of wideband code division multiple access based systems, this asynchronism stands for the loss of the orthogonality of the spreading codes allocated to users and thus, for an increase in the MUI level of the system. In this contribution, we propose a framework for mitigating the MUI which builds in three main steps: definition of a cooperation area based on the channel characteristics, statistical modeling of the average MUI power experienced by each user and a specific spreading code allocation scheme for users served with joint processing. This code allocation assigns spreading codes to users in such a way that minimum average cross-correlation between active users can be achieved. Interestingly, these steps can be performed with a limited amount of extra feedback from the user's side

Lightly synchronized Multipacket Reception in Machine-Type Communications Networks

Machine Type Communication (MTC) applications were designed to monitor and control elements of our surroundings and environment. MTC applications have a different set of requirements compared to the traditional communication devices, with Machine to Machine (M2M) data being mostly short, asynchronous, bursty and sometimes requiring end-to-end delays below 1ms. With the growth of MTC, the new generation of mobile communications has to be able to present different types of services with very different requirements, i.e. the same network has to be capable of "supplying" connection to the user that just wants to download a video or use social media, allowing at the same time MTC that has completely different requirements, without deteriorating both experiences. The challenges associated to the implementation of MTC require disruptive changes at the Physical (PHY) and Medium Access Control (MAC) layers, that lead to a better use of the spectrum available. The orthogonality and synchronization requirements of the PHY layer of current Long Term Evolution Advanced (LTE-A) radio access network (based on glsofdm and Single Carrier Frequency Domain Equalization (SC-FDE)) are obstacles for this new 5th Generation (5G) architecture. Generalized Frequency Division Multiplexing (GFDM) and other modulation techniques were proposed as candidates for the 5G PHY layer, however they also suffer from visible degradation when the transmitter and receiver are not synchronized, leading to a poor performance when collisions occur in an asynchronous MAC layer. This dissertation addresses the requirements of M2M traffic at the MAC layer applying multipacket reception (MPR) techniques to handle the bursty nature of the traffic and synchronization tones and optimized back-off approaches to reduce the delay. It proposes a new MAC protocol and analyses its performance analytically considering an SC-FDE modulation. The models are validated using a system level cross-layer simulator developed in MATLAB, which implements the MAC protocol and applies PHY layer performance models. The results show that the MAC’s latency depends mainly on the number of users and the load of each user, and can be controlled using these two parameters

BER performance study for optical OFDM of optical camera communication

In this article, different forms of optical orthogonal frequency division multiplexing (OFDM) were observed which were suitable for optical camera communication (OCC) systems. This research aims to establish the bit error rate (BER) versus signal-to-noise ratio (SNR) of the OCC system. This research will focus on OCC systems and the design that produces the noise of the clipping but will gain SNR as a whole if an optimum clipping factor is chosen. The BER versus SNR analysis was investigated for the different clipping factors 0.7, 1.4, and 2.6. The BER performance of the asymmetrically clipped optical OFDM (ACO-OFDM) was also compared with the direct current optical OFDM (DCO-OFDM) to show the suitable effectiveness of the proposed approach. ACO-OFDM was considered to be better due to lower bit loading, but DCO-OFDM was efficient for higher SNR values. This was because the DC bias used was inefficient in terms of optical capacity, while ACO-OFDM used only half of the subcarriers to transmit the information. Moreover, ACO-OFDM two-dimensional half-subcarriers of mapping rule would introduce the clipping noise to its unused 2D subcarriers, although further data can be provided by the 2D DCO-OFDM mapping rule

Autonomous Algorithms for Centralized and Distributed Interference Coordination: A Virtual Layer Based Approach

Interference mitigation techniques are essential for improving the performance of interference limited wireless networks. In this paper, we introduce novel interference mitigation schemes for wireless cellular networks with space division multiple access (SDMA). The schemes are based on a virtual layer that captures and simplifies the complicated interference situation in the network and that is used for power control. We show how optimization in this virtual layer generates gradually adapting power control settings that lead to autonomous interference minimization. Thereby, the granularity of control ranges from controlling frequency sub-band power via controlling the power on a per-beam basis, to a granularity of only enforcing average power constraints per beam. In conjunction with suitable short-term scheduling, our algorithms gradually steer the network towards a higher utility. We use extensive system-level simulations to compare three distributed algorithms and evaluate their applicability for different user mobility assumptions. In particular, it turns out that larger gains can be achieved by imposing average power constraints and allowing opportunistic scheduling instantaneously, rather than controlling the power in a strict way. Furthermore, we introduce a centralized algorithm, which directly solves the underlying optimization and shows fast convergence, as a performance benchmark for the distributed solutions. Moreover, we investigate the deviation from global optimality by comparing to a branch-and-bound-based solution.Comment: revised versio