Interfacing synchronous and asynchronous domains for open core protocol

pre-printIntellectual property (IP) blocks are connected in a system on chip using a bus or network-on-chip (NoC). IP reuse is facilitated by the modularity that results when using common interfaces between the IP cores and the bus or NoC. This paper investigates and implements several versions of one of the common interfaces, the open core protocol (OCP). The paper addresses two new aspects of interface design. First, an approach is developed to partition the common protocol portion of the interface from the interface back-end which is specific to the particular IP. This is achieved with a component we call a domain interface at this boundary. Second, the domain interface is enhanced to synchronize between IP blocks and busses that use different clock frequencies or asynchronous (unclocked) logic. As a result IP operating at unrelated frequency and fully asynchronous (unclocked) blocks can more easily be integrated into a system. Results are reported for power, performance and area for these clocked and asynchronous implementations

Master of Science

thesisThis thesis designs, implements, and evaluates modular Open Core Protocol (OCP) interfaces for Intellectual Property (IP) cores and Network-on-Chip (NoC) that re- duces System-On-Chip (SoC) design time and enables research on di erent architectural sequencing control methods. To utilize the NoCs design time optimization feature at the boundaries, a standardized industry socket was required, which can address the SoC shorter time-to-market requirements, design issues, and also the subsequent reuse of developed IP cores. OCP is an open industry standard socket interface speci cation used in this research to enable the IP cores reusability across multiple SoC designs. This research work designs and implements clocked OCP interfaces between IP cores and On-Chip Network Fabric (NoC), in single- and multi- frequency clocked domains. The NoC interfaces between IP cores and on-chip network fabric are implemented using the standard network interface structure. It consists of back-end and front-end submodules corresponding to customized interfaces to IP cores or network fabric and OCP Master and Slave entities, respectively. A generic domain interface (DI) protocol is designed which acts as the bridge between back-end and front-end submodules for synchronization and data ow control. Clocked OCP interfaces are synthesized, placed and routed using IBM's 65nm process technology. The implemented designs are veri ed for OCP compliance using SOLV (Sonics OCP Library for Veri cation). Finally, this thesis reports the performance metrics such as design target frequency of operation, latency, area, energy per transaction, and maximum bandwidth across network on-chip for single- and multifrequency clocked designs

The Future of Formal Methods and GALS Design

AbstractThe System-on-Chip era has arrived, and it arrived quickly. Modular composition of components through a shared interconnect is now becoming the standard, rather than the exotic. Asynchronous interconnect fabrics and globally asynchronous locally synchronous (GALS) design has been shown to be potentially advantageous. However, the arduous road to developing asynchronous on-chip communication and interfaces to clocked cores is still nascent. This road of converting to asynchronous networks, and potentially the core intellectual property block as well, will be rocky. Asynchronous circuit design has been employed since the 1950's. However, it is doubtful that its present form will be what we will see 10 years hence. This treatise is intended to provoke debate as it projects what technologies will look like in the future, and discusses, among other aspects, the role of formal verification, education, the CAD industry, and the ever present tradeoff between greed and fear

From FPGA to ASIC: A RISC-V processor experience

This work document a correct design flow using these tools in the Lagarto RISC- V Processor and the RTL design considerations that must be taken into account, to move from a design for FPGA to design for ASIC

Radiation safety based on the sky shine effect in reactor

In the reactor operation, neutrons and gamma rays are the most dominant radiation. As protection, lead and concrete shields are built around the reactor. However, the radiation can penetrate the water shielding inside the reactor pool. This incident leads to the occurrence of sky shine where a physical phenomenon of nuclear radiation sources was transmitted panoramic that extends to the environment. The effect of this phenomenon is caused by the fallout radiation into the surrounding area which causes the radiation dose to increase. High doses of exposure cause a person to have stochastic effects or deterministic effects. Therefore, this study was conducted to measure the radiation dose from sky shine effect that scattered around the reactor at different distances and different height above the reactor platform. In this paper, the analysis of the radiation dose of sky shine effect was measured using the experimental metho

Doctor of Philosophy

dissertationAsynchronous design has a very promising potential even though it has largely received a cold reception from industry. Part of this reluctance has been due to the necessity of custom design languages and computer aided design (CAD) flows to design, optimize, and validate asynchronous modules and systems. Next generation asynchronous flows should support modern programming languages (e.g., Verilog) and application specific integrated circuits (ASIC) CAD tools. They also have to support multifrequency designs with mixed synchronous (clocked) and asynchronous (unclocked) designs. This work presents a novel relative timing (RT) based methodology for generating multifrequency designs using synchronous CAD tools and flows. Synchronous CAD tools must be constrained for them to work with asynchronous circuits. Identification of these constraints and characterization flow to automatically derive the constraints is presented. The effect of the constraints on the designs and the way they are handled by the synchronous CAD tools are analyzed and reported in this work. The automation of the generation of asynchronous design templates and also the constraint generation is an important problem. Algorithms for automation of reset addition to asynchronous circuits and power and/or performance optimizations applied to the circuits using logical effort are explored thus filling an important hole in the automation flow. Constraints representing cyclic asynchronous circuits as directed acyclic graphs (DAGs) to the CAD tools is necessary for applying synchronous CAD optimizations like sizing, path delay optimizations and also using static timing analysis (STA) on these circuits. A thorough investigation for the requirements of cycle cutting while preserving timing paths is presented with an algorithm to automate the process of generating them. A large set of designs for 4 phase handshake protocol circuit implementations with early and late data validity are characterized for area, power and performance. Benchmark circuits with automated scripts to generate various configurations for better understanding of the designs are proposed and analyzed. Extension to the methodology like addition of scan insertion using automatic test pattern generation (ATPG) tools to add testability of datapath in bundled data asynchronous circuit implementations and timing closure approaches are also described. Energy, area, and performance of purely asynchronous circuits and circuits with mixed synchronous and asynchronous blocks are explored. Results indicate the benefits that can be derived by generating circuits with asynchronous components using this methodology

Mobile Robots

The objective of this book is to cover advances of mobile robotics and related technologies applied for multi robot systems' design and development. Design of control system is a complex issue, requiring the application of information technologies to link the robots into a single network. Human robot interface becomes a demanding task, especially when we try to use sophisticated methods for brain signal processing. Generated electrophysiological signals can be used to command different devices, such as cars, wheelchair or even video games. A number of developments in navigation and path planning, including parallel programming, can be observed. Cooperative path planning, formation control of multi robotic agents, communication and distance measurement between agents are shown. Training of the mobile robot operators is very difficult task also because of several factors related to different task execution. The presented improvement is related to environment model generation based on autonomous mobile robot observations