Assessing the effectiveness of managed lane strategies for the rapid deployment of cooperative adaptive cruise control technology

Connected and Automated Vehicle (C/AV) technologies are fast expanding in the transportation and automotive markets. One of the highly researched examples of C/AV technologies is the Cooperative Adaptive Cruise Control (CACC) system, which exploits various vehicular sensors and vehicle-to-vehicle communication to automate vehicular longitudinal control. The operational strategies and network-level impacts of CACC have not been thoroughly discussed, especially in near-term deployment scenarios where Market Penetration Rate (MPR) is relatively low. Therefore, this study aims to assess CACC\u27s impacts with a combination of managed lane strategies to provide insights for CACC deployment. The proposed simulation framework incorporates 1) the Enhanced Intelligent Driver Model; 2) Nakagami-based radio propagation model; and 3) a multi-objective optimization (MOOP)-based CACC control algorithm. The operational impacts of CACC are assessed under four managed lane strategies (i.e., mixed traffic (UML), HOV (High Occupancy Vehicle)-CACC lane (MML), CACC dedicated lane (DL), and CACC dedicated lane with access control (DLA)). Simulation results show that the introduction of CACC, even with 10% MPR, is able to improve the network throughput by 7% in the absence of any managed lane strategies. The segment travel times for both CACC and non-CACC vehicles are reduced. The break-even point for implementing dedicated CACC lane is 30% MPR, below which the priority usage of the current HOV lane for CACC traffic is found to be more appropriate. It is also observed that DLA strategy is able to consistently increase the percentage of platooned CACC vehicles as MPR grows. The percentage of CACC vehicles within a platoon reaches 52% and 46% for DL and DLA, respectively. When it comes to the impact of vehicle-to-vehicle (V2V), it is found that DLA strategy provides more consistent transmission density in terms of median and variance when MPR reaches 20% or above. Moreover, the performance of the MOOP-based cooperative driving is examined. With average 75% likelihood of obtaining a feasible solution, the MOOP outperforms its counterpart which aims to minimize the headway objective solely. In UML, MML, and DL strategy, the proposed control algorithm achieves a balance spread among four objectives for each CACC vehicle. In the DLA strategy, however, the probability of obtaining feasible solution falls to 60% due to increasing size of platoon owing to DLA that constraints the feasible region by introduction more dimensions in the search space. In summary, UML or MML is the preferred managed lane strategy for improving traffic performance when MPR is less than 30%. When MRP reaches 30% or above, DL and DLA could improve the CACC performance by facilitating platoon formation. If available, priority access to an existing HOV lane can be adopted to encourage adaptation of CACC when CACC technology becomes publically available

Impacts of Connected and Automated Vehicles on Energy and Traffic Flow: Optimal Control Design and Verification Through Field Testing

This dissertation assesses eco-driving effectiveness in several key traffic scenarios that include passenger vehicle transportation in highway driving and urban driving that also includes interactions with traffic signals, as well as heavy-duty line-haul truck transportation in highway driving with significant road grade. These studies are accomplished through both traffic microsimulation that propagates individual vehicle interactions to synthesize large-scale traffic patterns that emerge from the eco-driving strategies, and through experimentation in which real prototyped connected and automated vehicles (CAVs) are utilized to directly measure energy benefits from the designed eco-driving control strategies. In particular, vehicle-in-the-loop is leveraged for the CAVs driven on a physical test track to interact with surrounding traffic that is virtually realized through said microsimulation software in real time. In doing so, model predictive control is designed and implemented to create performative eco-driving policies and to select vehicle lane, as well as enforce safety constraints while autonomously driving a real vehicle. Ultimately, eco-driving policies are both simulated and experimentally vetted in a variety of typical driving scenarios to show up to a 50% boost in fuel economy when switching to CAV drivers without compromising traffic flow. The first part of this dissertation specifically assesses energy efficiency of connected and automated passenger vehicles that exploit intention-sharing sourced from both neighboring vehicles in a highway scene and from traffic lights in an urban scene. Linear model predictive control is implemented for CAV motion planning, whereby chance constraints are introduced to balance between traffic compactness and safety, and integer decision variables are introduced for lane selection and collision avoidance in multi-lane environments. Validation results are shown from both large-scale microsimulation and through experimentation of real prototyped CAVs. The second part of this dissertation then assesses energy efficiency of automated line-haul trucks when tasked to aerodynamically platoon. Nonlinear model predictive control is implemented for motion planning, and simulation and experimentation are conducted for platooning verification under highway conditions with traffic. Then, interaction-aware and intention-sharing cooperative control is further introduced to eliminate experimentally measured platoon disengagements that occur on real highways when using only status-sharing control. Finally, the performance of automated drivers versus human drivers are compared in a point-to-point scenario to verify fundamental eco-driving impacts -- experimentally showing eco-driving to boost energy economy by 11% on average even in simple driving scenarios

2nd Symposium on Management of Future motorway and urban Traffic Systems (MFTS 2018): Booklet of abstracts: Ispra, 11-12 June 2018

The Symposium focuses on future traffic management systems, covering the subjects of traffic control, estimation, and modelling of motorway and urban networks, with particular emphasis on the presence of advanced vehicle communication and automation technologies. As connectivity and automation are being progressively introduced in our transport and mobility systems, there is indeed a growing need to understand the implications and opportunities for an enhanced traffic management as well as to identify innovative ways and tools to optimise traffic efficiency. In particular the debate on centralised versus decentralised traffic management in the presence of connected and automated vehicles has started attracting the attention of the research community. In this context, the Symposium provides a remarkable opportunity to share novel ideas and discuss future research directions.JRC.C.4-Sustainable Transpor

Fuel Efficient Connected Cruise Control for Heavy-Duty Trucks in Real Traffic

In this paper, we present a systematic approach for fuel-economy optimization of a connected automated truck that utilizes motion information from multiple vehicles ahead via vehicle-to-vehicle (V2V) communication. Position and velocity data collected from a chain of human-driven vehicles are utilized to design a connected cruise controller that smoothly responds to traffic perturbations while maximizing energy efficiency. The proposed design is evaluated using a high-fidelity truck model and the robustness of the design is validated on real traffic data sets. It is shown that optimally utilizing V2V connectivity leads to around 10% fuel economy improvements compared to the best nonconnected design

Fuel Efficient Connected Cruise Control for Heavy-Duty Trucks in Real Traffic

In this paper, we present a systematic approach for fuel-economy optimization of a connected automated truck that utilizes motion information from multiple vehicles ahead via vehicle-to-vehicle (V2V) communication. Position and velocity data collected from a chain of human-driven vehicles are utilized to design a connected cruise controller that smoothly responds to traffic perturbations while maximizing energy efficiency. The proposed design is evaluated using a high-fidelity truck model and the robustness of the design is validated on real traffic data sets. It is shown that optimally utilizing V2V connectivity leads to around 10% fuel economy improvements compared to the best nonconnected design