Analysis of a new family of DC-DC converters with input-parallel output-series structure

There is an increasing trend of development and installation of switching power supplies due to their highly efficient power conversion, fast power control and high quality power conditioning for applications such as renewable energy integration and energy storage management systems. In most of these applications, high voltage conversion ratio is required. However, basic switching converters have limited voltage conversion ratio. There has been much research into development of high gain power converters. While most of the reported topologies focus on high gain and high efficiency, in this thesis, the input and output ripple currents and reliability are also considered to derive a new converter structure suitable for high step-up voltage conversion applications. High ripple currents and voltages at the input and output of dc-dc converters are not desirable because they may affect the operation of the dc source or the load. A number of converters operating in an interleaved manner can reduce these ripples. This thesis proposes a dc/dc switching converter structure which is capable of reducing the ripple problem through interleaved action, in addition to high gain and high efficiency voltage conversion. The thesis analyses the proposed converter structure through a dual buck-boost converter topology. The structure allows different converter topologies and combinations of them for different applications to be configured. The study begins with a motivation and a literature review of dc/dc converters. The new family of high step-up converters is introduced with an interleaved buck-boost as an example, followed by small-signal analysis. Experimental verifications, conclusions and future work are discussed

Auxiliary power supply based on a modular ISOP Flyback configuration with very high input voltage

This paper proposes a Flyback-based Input-Series Output-Parallel (ISOP) Auxiliary Power Supply (APS), intended to feed the control system of the cells of a Solid-State Transformer (SST). The SST topology is based on a modular Multiport Multilevel Converter (MMC). Energization of the cells auxiliary circuitry is not trivial due to the high voltages involved (tens of kV for the electric power distribution system), most of the commercially available control and driving circuitry not being usable due to the isolation requirements. It is possible to energize the control circuitry from an APS, connected to the cell capacitor voltage. However, in the SST under consideration, cells target DC voltage is in the range of 1.5kV to 2.5kV. Design of an APS capable of feeding the auxiliary circuitry from such high voltage and the required isolation is not trivial. A modular APS using autonomous Flyback converters in Continuous Conduction Mode (CCM) and based on commercial AC adapters is proposed in this paper. The solution is scalable and therefore applicable to cells with larger DC voltage

Analysis of a new family of DC-DC converters with input-parallel output-series structure

There is an increasing trend of development and installation of switching power supplies due to their highly efficient power conversion, fast power control and high quality power conditioning for applications such as renewable energy integration and energy storage management systems. In most of these applications, high voltage conversion ratio is required. However, basic switching converters have limited voltage conversion ratio. There has been much research into development of high gain power converters. While most of the reported topologies focus on high gain and high efficiency, in this thesis, the input and output ripple currents and reliability are also considered to derive a new converter structure suitable for high step-up voltage conversion applications. High ripple currents and voltages at the input and output of dc-dc converters are not desirable because they may affect the operation of the dc source or the load. A number of converters operating in an interleaved manner can reduce these ripples. This thesis proposes a dc/dc switching converter structure which is capable of reducing the ripple problem through interleaved action, in addition to high gain and high efficiency voltage conversion. The thesis analyses the proposed converter structure through a dual buck-boost converter topology. The structure allows different converter topologies and combinations of them for different applications to be configured. The study begins with a motivation and a literature review of dc/dc converters. The new family of high step-up converters is introduced with an interleaved buck-boost as an example, followed by small-signal analysis. Experimental verifications, conclusions and future work are discussed

Power Electronic Converters for Single-Phase Grid Connected Photovoltaic System: An Overview

The Solar photovoltaic (PV) power system have achieved meteoric rise through the years. The uptake is not difficult to explain – a drop in cost of PV systems and spiraling electricity cost, have  encouraged the end-user to lessen their bills by producing cheaper electricity and can generate revenue  by feeding excess power back to the grid. The solar PV is intermittent in nature so it dependent on irradiance and ambient temperature. Power electronics technologies plays an important part for optimizing the energy harvesting from PV system. In order to get maximum extracted power and ensure the load is supplied with a good quality voltage, different dc-dc converters topologies and inverters configurations are used. This paper provides an overview of PV inverter configurations and DC-DC topologies to offer a useful insight and reference point for the researchers working in the field of photovoltaic system

Design, Modeling, And Control Of Three-port Converters For Solar Power Applications

This paper describes the results of research into multi-port converter design and control, specifically a pair of three-port topologies based on the half-bridge and full-bridge topologies. These converters are capable of simultaneous and independent regulation of two out of their three ports, while the third port provides the power balance in the system. A dynamic model was developed for each topology to aid in testing and for designing the control loops. The models were then used to design the control structures, and the results were tested in Simulink. In addition, a basic outline of a system level architecture to control multiple converters working in parallel is presented. To improve the reliability of this system, output current sharing controls were also developed. Finally, one of the topologies is analyzed in detail in order to obtain a set of design equations that can be used to improve the efficiency, weight, and cost of the converter for a specific application

Multiple-output DC–DC converters: applications and solutions

Multiple-output DC–DC converters are essential in a multitude of applications where different DC output voltages are required. The interest and importance of this type of multiport configuration is also reflected in that many electronics manufacturers currently develop integrated solutions. Traditionally, the different output voltages required are obtained by means of a transformer with several windings, which are in addition to providing electrical isolation. However, the current trend in the development of multiple-output DC–DC converters follows general aspects, such as low losses, high-power density, and high efficiency, as well as the development of new architectures and control strategies. Certainly, simple structures with a reduced number of components and power switches will be one of the new trends, especially to reduce the size. In this sense, the incorporation of devices with a Wide Band Gap (WBG), particularly Gallium Nitride (GaN) and Silicon Carbide (SiC), will establish future trends, advantages, and disadvantages in the development and applications of multiple-output DC–DC converters. In this paper, we present a review of the most important topics related to multiple-output DC–DC converters based on their main topologies and configurations, applications, solutions, and trends. A wide variety of configurations and topologies of multiple-output DC–DC converters are shown (more than 30), isolated and non-isolated, single and multiple switches, and based on soft and hard switching techniques, which are used in many different applications and solutions.info:eu-repo/semantics/publishedVersio

Design and Control of Power Converters 2020

In this book, nine papers focusing on different fields of power electronics are gathered, all of which are in line with the present trends in research and industry. Given the generality of the Special Issue, the covered topics range from electrothermal models and losses models in semiconductors and magnetics to converters used in high-power applications. In this last case, the papers address specific problems such as the distortion due to zero-current detection or fault investigation using the fast Fourier transform, all being focused on analyzing the topologies of high-power high-density applications, such as the dual active bridge or the H-bridge multilevel inverter. All the papers provide enough insight in the analyzed issues to be used as the starting point of any research. Experimental or simulation results are presented to validate and help with the understanding of the proposed ideas. To summarize, this book will help the reader to solve specific problems in industrial equipment or to increase their knowledge in specific fields

A New Single-Phase Single-Stage AC-DC Stacked Flyback Converter With Active Clamp ZVS

Single-stage AC-DC converters integrate an AC-DC front-end converter with a DC-DC back-end converter. Compared with conventional two-stage AC-DC converters, single-stage AC-DC converters use less components and only one controller, which is used to regulate the output voltage. As a result, the cost, size and complexity of AC-DC converters can be reduced, but single-stage converters do not perform as well as two-stage converters, and most have drawbacks that are related to the fact that the DC bus voltage is not controlled an can become excessive. A new single-phase single-stage AC-DC converter that uses stacked flyback converters is proposed in this thesis. The proposed converter consists of two low power flyback converters stacked on top of each other and an active clamp that helps the main switches operate with ZVS. The stacked structure helps reduce the voltage stresses typical fund in many single-stage converters. In the thesis, the operation of the converter is explained, the steady-state characteristics of the converter are determined and its design is discussed. The feasibility of the new converter is confirmed with experimental results obtained from a 100VAC~220VAC worldwide input, 48V output, 100kHz switching frequency and 200 W output power prototype converter