DPA on quasi delay insensitive asynchronous circuits: formalization and improvement

The purpose of this paper is to formally specify a flow devoted to the design of Differential Power Analysis (DPA) resistant QDI asynchronous circuits. The paper first proposes a formal modeling of the electrical signature of QDI asynchronous circuits. The DPA is then applied to the formal model in order to identify the source of leakage of this type of circuits. Finally, a complete design flow is specified to minimize the information leakage. The relevancy and efficiency of the approach is demonstrated using the design of an AES crypto-processor.Comment: Submitted on behalf of EDAA (http://www.edaa.com/

Sophisticated security verification on routing repaired balanced cell-based dual-rail logic against side channel analysis

Conventional dual-rail precharge logic suffers from difficult implementations of dual-rail structure for obtaining strict compensation between the counterpart rails. As a light-weight and high-speed dual-rail style, balanced cell-based dual-rail logic (BCDL) uses synchronised compound gates with global precharge signal to provide high resistance against differential power or electromagnetic analyses. BCDL can be realised from generic field programmable gate array (FPGA) design flows with constraints. However, routings still exist as concerns because of the deficient flexibility on routing control, which unfavourably results in bias between complementary nets in security-sensitive parts. In this article, based on a routing repair technique, novel verifications towards routing effect are presented. An 8 bit simplified advanced encryption processing (AES)-co-processor is executed that is constructed on block random access memory (RAM)-based BCDL in Xilinx Virtex-5 FPGAs. Since imbalanced routing are major defects in BCDL, the authors can rule out other influences and fairly quantify the security variants. A series of asymptotic correlation electromagnetic (EM) analyses are launched towards a group of circuits with consecutive routing schemes to be able to verify routing impact on side channel analyses. After repairing the non-identical routings, Mutual information analyses are executed to further validate the concrete security increase obtained from identical routing pairs in BCDL

Quantum computing on encrypted data

The ability to perform computations on encrypted data is a powerful tool for protecting privacy. Recently, protocols to achieve this on classical computing systems have been found. Here we present an efficient solution to the quantum analogue of this problem that enables arbitrary quantum computations to be carried out on encrypted quantum data. We prove that an untrusted server can implement a universal set of quantum gates on encrypted quantum bits (qubits) without learning any information about the inputs, while the client, knowing the decryption key, can easily decrypt the results of the computation. We experimentally demonstrate, using single photons and linear optics, the encryption and decryption scheme on a set of gates sufficient for arbitrary quantum computations. Because our protocol requires few extra resources compared to other schemes it can be easily incorporated into the design of future quantum servers. These results will play a key role in enabling the development of secure distributed quantum systems

Null Convention Logic applications of asynchronous design in nanotechnology and cryptographic security

This dissertation presents two Null Convention Logic (NCL) applications of asynchronous logic circuit design in nanotechnology and cryptographic security. The first application is the Asynchronous Nanowire Reconfigurable Crossbar Architecture (ANRCA); the second one is an asynchronous S-Box design for cryptographic system against Side-Channel Attacks (SCA). The following are the contributions of the first application: 1) Proposed a diode- and resistor-based ANRCA (DR-ANRCA). Three configurable logic block (CLB) structures were designed to efficiently reconfigure a given DR-PGMB as one of the 27 arbitrary NCL threshold gates. A hierarchical architecture was also proposed to implement the higher level logic that requires a large number of DR-PGMBs, such as multiple-bit NCL registers. 2) Proposed a memristor look-up-table based ANRCA (MLUT-ANRCA). An equivalent circuit simulation model has been presented in VHDL and simulated in Quartus II. Meanwhile, the comparison between these two ANRCAs have been analyzed numerically. 3) Presented the defect-tolerance and repair strategies for both DR-ANRCA and MLUT-ANRCA. The following are the contributions of the second application: 1) Designed an NCL based S-Box for Advanced Encryption Standard (AES). Functional verification has been done using Modelsim and Field-Programmable Gate Array (FPGA). 2) Implemented two different power analysis attacks on both NCL S-Box and conventional synchronous S-Box. 3) Developed a novel approach based on stochastic logics to enhance the resistance against DPA and CPA attacks. The functionality of the proposed design has been verified using an 8-bit AES S-box design. The effects of decision weight, bitstream length, and input repetition times on error rates have been also studied. Experimental results shows that the proposed approach enhances the resistance to against the CPA attack by successfully protecting the hidden key --Abstract, page iii

Asynchronous Advanced Encryption Standard Hardware with Random Noise Injection for Improved Side-Channel Attack Resistance

This work presents the design, hardware implementation, and performance analysis of novel asynchronous AES (advanced encryption standard) Key Expander and Round Function, which offer increased side-channel attack (SCA) resistance. These designs are based on a delay-insensitive (DI) logic paradigm known as null convention logic (NCL), which supports useful properties for resisting SCAs including dual-rail encoding, clock-free operation, and monotonic transitions. Potential benefits include reduced and more uniform switching activities and reduced signal-to-noise (SNR) ratio. A novel method to further augment NCL AES hardware with random voltage scaling technique is also presented for additional security. Thereby, the proposed components leak significantly less side-channel information than conventional clocked approaches. To quantitatively verify such improvements, functional verification and WASSO (weighted average simultaneous switching output) analysis have been carried out on both conventional synchronous approach and the proposed NCL based approach using Mentor Graphics ModelSim and Xilinx simulation tools. Hardware implementation has been carried out on both designs exploiting a specified side-channel attack standard evaluation FPGA board, called SASEBO-GII, and the corresponding power waveforms for both designs have been collected. Along with the results of software simulations, we have analyzed the collected waveforms to validate the claims related to benefits of the proposed cryptohardware design approach

Designing Novel Hardware Security Primitives for Smart Computing Devices

Smart computing devices are miniaturized electronics devices that can sense their surroundings, communicate, and share information autonomously with other devices to work cohesively. Smart devices have played a major role in improving quality of the life and boosting the global economy. They are ubiquitously present, smart home, smart city, smart girds, industry, healthcare, controlling the hazardous environment, and military, etc. However, we have witnessed an exponential rise in potential threat vectors and physical attacks in recent years. The conventional software-based security approaches are not suitable in the smart computing device, therefore, hardware-enabled security solutions have emerged as an attractive choice. Developing hardware security primitives, such as True Random Number Generator (TRNG) and Physically Unclonable Function (PUF) from electrical properties of the sensor could be a novel research direction. Secondly, the Lightweight Cryptographic (LWC) ciphers used in smart computing devices are found vulnerable against Correlation Power Analysis (CPA) attack. The CPA performs statistical analysis of the power consumption of the cryptographic core and reveals the encryption key. The countermeasure against CPA results in an increase in energy consumption, therefore, they are not suitable for battery operated smart computing devices. The primary goal of this dissertation is to develop novel hardware security primitives from existing sensors and energy-efficient LWC circuit implementation with CPA resilience. To achieve these. we focus on developing TRNG and PUF from existing photoresistor and photovoltaic solar cell sensors in smart devices Further, we explored energy recovery computing (also known as adiabatic computing) circuit design technique that reduces the energy consumption compared to baseline CMOS logic design and same time increasing CPA resilience in low-frequency applications, e.g. wearable fitness gadgets, hearing aid and biomedical instruments. The first contribution of this dissertation is to develop a TRNG prototype from the uncertainty present in photoresistor sensors. The existing sensor-based TRNGs suffer a low random bit generation rate, therefore, are not suitable in real-time applications. The proposed prototype has an average random bit generation rate of 8 kbps, 32 times higher than the existing sensor-based TRNG. The proposed lightweight scrambling method results in random bit entropy close to ideal value 1. The proposed TRNG prototype passes all 15 statistical tests of the National Institute of Standards and Technology (NIST) Statistical Test Suite with quality performance. The second contribution of this dissertation is to develop an integrated TRNG-PUF designed using photovoltaic solar cell sensors. The TRNG and PUF are mutually independent in the way they are designed, therefore, integrating them as one architecture can be beneficial in resource-constrained computing devices. We propose a novel histogram-based technique to segregate photovoltaic solar cell sensor response suitable for TRNG and PUF respectively. The proposed prototype archives approximately 34\% improvement in TRNG output. The proposed prototype achieves an average of 92.13\% reliability and 50.91\% uniformity performance in PUF response. The proposed sensor-based hardware security primitives do not require additional interfacing hardware. Therefore, they can be ported as a software update on existing photoresistor and photovoltaic sensor-based devices. Furthermore, the sensor-based design approach can identify physically tempered and faulty sensor nodes during authentication as their response bit differs. The third contribution is towards the development of a novel 2-phase sinusoidal clocking implementation, 2-SPGAL for existing Symmetric Pass Gate Adiabatic Logic (SPGAL). The proposed 2-SPGAL logic-based LWC cipher PRESENT shows an average of 49.34\% energy saving compared to baseline CMOS logic implementation. Furthermore, the 2-SPGAL prototype has an average of 22.76\% better energy saving compared to 2-EE-SPFAL (2-phase Energy-Efficient-Secure Positive Feedback Adiabatic Logic). The proposed 2-SPGAL was tested for energy-efficiency performance for the frequency range of 50 kHz to 250 kHz, used in healthcare gadgets and biomedical instruments. The proposed 2-SPGAL based design saves 16.78\% transistor count compared to 2-EE-SPFAL counterpart. The final contribution is to explore Clocked CMOS Adiabatic Logic (CCAL) to design a cryptographic circuit. Previously proposed 2-SPGAL and 2-EE-SPFAL uses two complementary pairs of the transistor evaluation network, thus resulting in a higher transistor count compared to the CMOS counterpart. The CCAL structure is very similar to CMOS and unlike 2-SPGAL and 2-EE-SPFAL, it does not require discharge circuitry to improve security performance. The case-study implementation LWC cipher PRESENT S-Box using CCAL results into 45.74\% and 34.88\% transistor count saving compared to 2-EE-SPFAL and 2-SPGAL counterpart. Furthermore, the case-study implementation using CCAL shows more than 95\% energy saving compared to CMOS logic at frequency range 50 kHz to 125 kHz, and approximately 60\% energy saving at frequency 250 kHz. The case study also shows 32.67\% and 11.21\% more energy saving compared to 2-EE-SPFAL and 2-SPGAL respectively at frequency 250 kHz. We also show that 200 fF of tank capacitor in the clock generator circuit results in optimum energy and security performance in CCAL

ENERGY-EFFICIENT AND SECURE HARDWARE FOR INTERNET OF THINGS (IoT) DEVICES

Internet of Things (IoT) is a network of devices that are connected through the Internet to exchange the data for intelligent applications. Though IoT devices provide several advantages to improve the quality of life, they also present challenges related to security. The security issues related to IoT devices include leakage of information through Differential Power Analysis (DPA) based side channel attacks, authentication, piracy, etc. DPA is a type of side-channel attack where the attacker monitors the power consumption of the device to guess the secret key stored in it. There are several countermeasures to overcome DPA attacks. However, most of the existing countermeasures consume high power which makes them not suitable to implement in power constraint devices. IoT devices are battery operated, hence it is important to investigate the methods to design energy-efficient and secure IoT devices not susceptible to DPA attacks. In this research, we have explored the usefulness of a novel computing platform called adiabatic logic, low-leakage FinFET devices and Magnetic Tunnel Junction (MTJ) Logic-in-Memory (LiM) architecture to design energy-efficient and DPA secure hardware. Further, we have also explored the usefulness of adiabatic logic in the design of energy-efficient and reliable Physically Unclonable Function (PUF) circuits to overcome the authentication and piracy issues in IoT devices. Adiabatic logic is a low-power circuit design technique to design energy-efficient hardware. Adiabatic logic has reduced dynamic switching energy loss due to the recycling of charge to the power clock. As the first contribution of this dissertation, we have proposed a novel DPA-resistant adiabatic logic family called Energy-Efficient Secure Positive Feedback Adiabatic Logic (EE-SPFAL). EE-SPFAL based circuits are energy-efficient compared to the conventional CMOS based design because of recycling the charge after every clock cycle. Further, EE-SPFAL based circuits consume uniform power irrespective of input data transition which makes them resilience against DPA attacks. Scaling of CMOS transistors have served the industry for more than 50 years in providing integrated circuits that are denser, and cheaper along with its high performance, and low power. However, scaling of the transistors leads to increase in leakage current. Increase in leakage current reduces the energy-efficiency of the computing circuits,and increases their vulnerability to DPA attack. Hence, it is important to investigate the crypto circuits in low leakage devices such as FinFET to make them energy-efficient and DPA resistant. In this dissertation, we have proposed a novel FinFET based Secure Adiabatic Logic (FinSAL) family. FinSAL based designs utilize the low-leakage FinFET device along with adiabatic logic principles to improve energy-efficiency along with its resistance against DPA attack. Recently, Magnetic Tunnel Junction (MTJ)/CMOS based Logic-in-Memory (LiM) circuits have been explored to design low-power non-volatile hardware. Some of the advantages of MTJ device include non-volatility, near-zero leakage power, high integration density and easy compatibility with CMOS devices. However, the differences in power consumption between the switching of MTJ devices increase the vulnerability of Differential Power Analysis (DPA) based side-channel attack. Further, the MTJ/CMOS hybrid logic circuits which require frequent switching of MTJs are not very energy-efficient due to the significant energy required to switch the MTJ devices. In the third contribution of this dissertation, we have investigated a novel approach of building cryptographic hardware in MTJ/CMOS circuits using Look-Up Table (LUT) based method where the data stored in MTJs are constant during the entire encryption/decryption operation. Currently, high supply voltage is required in both writing and sensing operations of hybrid MTJ/CMOS based LiM circuits which consumes a considerable amount of energy. In order to meet the power budget in low-power devices, it is important to investigate the novel design techniques to design ultra-low-power MTJ/CMOS circuits. In the fourth contribution of this dissertation, we have proposed a novel energy-efficient Secure MTJ/CMOS Logic (SMCL) family. The proposed SMCL logic family consumes uniform power irrespective of data transition in MTJ and more energy-efficient compared to the state-of-art MTJ/ CMOS designs by using charge sharing technique. The other important contribution of this dissertation is the design of reliable Physical Unclonable Function (PUF). Physically Unclonable Function (PUF) are circuits which are used to generate secret keys to avoid the piracy and device authentication problems. However, existing PUFs consume high power and they suffer from the problem of generating unreliable bits. This dissertation have addressed this issue in PUFs by designing a novel adiabatic logic based PUF. The time ramp voltages in adiabatic PUF is utilized to improve the reliability of the PUF along with its energy-efficiency. Reliability of the adiabatic logic based PUF proposed in this dissertation is tested through simulation based temperature variations and supply voltage variations