Spectral efficiency improvement of low peak-to-average power ratio complete complementary code division multiple access systems

An investigation into the peak-to-average power ratio (PAPR) performance of cyclic rotation complete complementary code division multiple access (CR-CC-CDMA) has been conducted. Additionally, a novel orthogonal signalling technique, referred to as complementary rotation keying (CRK), has been developed for improving the spectral efficiency (SE) of CC-CDMA whilst maintaining a low PAPR. The CRK system is based on the concept of CR of CC codes in order to allow interoperability with CR-CC-CDMA systems. To this end, both systems employ a similar transmitter and receiver structure. The CR-CC-CDMA technique suffers from increased PAPR as SE per user is increased. The CRK system offers an improvement in SE, while maintaining the PAPR of a CC-CDMA system. The bit error rates of both systems were unaffected in a joint system, indicating complete interoperability. This allows dynamic adjustment of the PAPR and SE of any user in the system, with users being able to switch between both systems without causing multi user interference.Dissertation (MEng)--University of Pretoria, 2018.Electrical, Electronic and Computer EngineeringMEn

Design and Linearization of Energy Efficiency Power Amplifier in Nonlinear OFDM Transmitter for LTE-5G Applications. Simulation and measurements of energy efficiency power amplifier in the presence of nonlinear OFDM transmitter system and digital predistortion based on Hammerstein-Wiener method

This research work has made an effort to understand a novel line of radio frequency power amplifiers (RFPAs) that address initiatives for efficiency enhancement and linearity compensation to harmonize the fifth generation (5G) campaign. The objective is to enhance the performance of an orthogonal frequency division multiplexing-long term evolution (OFDM-LTE) transmitter by reducing the nonlinear distortion of the RFPA. The first part of this work explores the design and implementation of 15.5 W class AB RF power amplifier, adopting a balanced technique to stimulate efficiency enhancement and redeeming exhibition of excessive power in the transmitter. Consequently, this work goes beyond improving efficiency over a linear RF power amplifier design; in which a comprehensive investigation on the fundamental and harmonic components of class F RF power amplifier using a load-pull approach to realise an optimum load impedance and the matching network is presented. The frequency bandwidth for both amplifiers was allocated to operate in the 2.620-2.690 GHz of mobile LTE applications. The second part explores the development of the behavioural model for the class AB power amplifier. A particular novel, Hammerstein-Wiener based model is proposed to describe the dynamic nonlinear behaviour of the power amplifier. The RF power amplifier nonlinear distortion is approximated using a new linear parameter approximation approach. The first and second-order Hammerstein-Wiener using the Normalised Least Mean Square Error (NLMSE) algorithm is used with the aim of easing the complexity of filtering process during linear memory cancellation. Moreover, an enhanced adaptive Wiener model is proposed to explore the nonlinear memory effect in the system. The proposed approach is able to balance between convergence speed and high-level accuracy when compared with behavioural modelling algorithms that are more complex in computation. Finally, the adaptive predistorter technique is implemented and verified in the OFDM transceiver test-bed. The results were compared against the computed one from MATLAB simulation for OFDM and 5G modulation transmitters. The results have confirmed the reliability of the model and the effectiveness of the proposed predistorter.Fundacão para a Ciência e a Tecnologia, Portugal, under European Union’s Horizon 2020 research and innovation programme ... grant agreement H2020-MSCA-ITN- 2016 SECRET-722424 I also acknowledge the role of the National Space Research and Development Agency (NASRDA) Sokoto State Government Petroleum Technology Trust Fund (PTDF

PAPR Reduction in Multicarrier Communication Systems Using Efficient Pulse Shaping Technique

Emerging multicarrier modulation schemes have been considered for the fifth generation (5G) communication systems. However, existing designs often suffer from a high peak-to-average power ratio (PAPR) in the transmitted signal. This thesis aims to (i) design pulse shaping filters to reduce the PAPR using computationally efficient optimisation approach (ii) investigate the performance of the multicarrier systems employing the designed filter and (iii) study the power utilisation efficiency of the nonlinear amplifier with the use of the designed filters

PAPR Analysis in OFDM-IQ-IM Systems

One of the key disadvantages of OFDM system, implemented already in 4G and 5G is high PAPR. For this reason, it is very important to evaluate the PAPR performance of any potential multiplexing technique candidate for upcoming generations. Due to the superior performance over OFDM considering BER performance, spectral efficiency, energy efficiency, OFDM-IQ-IM is one of the promising multiplexing techniques for upcoming generations of wireless technology. Therefore, the PAPR performance of OFDM-IQ-IM system has been analysed here. In deterministic approach, subcarriers are considered to be modulated by symbols with highest power and the upper limit of the PAPR of OFDM-IQ-IM system has been formulated. Using statistical distribution, a probabilistic approach has been taken to determine the PAPR performance of the OFDM-IQ-IM and OFDM-IM systems. The distribution of PAPR of OFDM-IQ-IM and OFDM-IM systems has been evaluated considering the discrete time baseband signals for both in-phase and quadrature components as independent Gaussian random variables. A comparative analysis of the PAPR of OFDM, OFDM-IM and OFDM-IQ-IM systems has been made in both deterministic and probabilistic approach. Thus improved PAPR performance has been noticed in OFDM-IQ-IM system compared to OFDM-IM and OFDM systems for same spectral efficiency

Unified Framework for Multicarrier and Multiple Access based on Generalized Frequency Division Multiplexing

The advancements in wireless communications are the key-enablers of new applications with stringent requirements in low-latency, ultra-reliability, high data rate, high mobility, and massive connectivity. Diverse types of devices, ranging from tiny sensors to vehicles, with different capabilities need to be connected under various channel conditions. Thus, modern connectivity and network techniques at all layers are essential to overcome these challenges. In particular, the physical layer (PHY) transmission is required to achieve certain link reliability, data rate, and latency. In modern digital communications systems, the transmission is performed by means of a digital signal processing module that derives analog hardware. The performance of the analog part is influenced by the quality of the hardware and the baseband signal denoted as waveform. In most of the modern systems such as fifth generation (5G) and WiFi, orthogonal frequency division multiplexing (OFDM) is adopted as a favorite waveform due to its low-complexity advantages in terms of signal processing. However, OFDM requires strict requirements on hardware quality. Many devices are equipped with simplified analog hardware to reduce the cost. In this case, OFDM does not work properly as a result of its high peak-to-average power ratio (PAPR) and sensitivity to synchronization errors. To tackle these problems, many waveforms design have been recently proposed in the literature. Some of these designs are modified versions of OFDM or based on conventional single subcarrier. Moreover, multicarrier frameworks, such as generalized frequency division multiplexing (GFDM), have been proposed to realize varieties of conventional waveforms. Furthermore, recent studies show the potential of using non-conventional waveforms for increasing the link reliability with affordable complexity. Based on that, flexible waveforms and transmission techniques are necessary to adapt the system for different hardware and channel constraints in order to fulfill the applications requirements while optimizing the resources. The objective of this thesis is to provide a holistic view of waveforms and the related multiple access (MA) techniques to enable efficient study and evaluation of different approaches. First, the wireless communications system is reviewed with specific focus on the impact of hardware impairments and the wireless channel on the waveform design. Then, generalized model of waveforms and MA are presented highlighting various special cases. Finally, this work introduces low-complexity architectures for hardware implementation of flexible waveforms. Integrating such designs with software-defined radio (SDR) contributes to the development of practical real-time flexible PHY.:1 Introduction 1.1 Baseband transmission model 1.2 History of multicarrier systems 1.3 The state-of-the-art waveforms 1.4 Prior works related to GFDM 1.5 Objective and contributions 2 Fundamentals of Wireless Communications 2.1 Wireless communications system 2.2 RF transceiver 2.2.1 Digital-analogue conversion 2.2.2 QAM modulation 2.2.3 Effective channel 2.2.4 Hardware impairments 2.3 Waveform aspects 2.3.1 Single-carrier waveform 2.3.2 Multicarrier waveform 2.3.3 MIMO-Waveforms 2.3.4 Waveform performance metrics 2.4 Wireless Channel 2.4.1 Line-of-sight propagation 2.4.2 Multi path and fading process 2.4.3 General baseband statistical channel model 2.4.4 MIMO channel 2.5 Summary 3 Generic Block-based Waveforms 3.1 Block-based waveform formulation 3.1.1 Variable-rate multicarrier 3.1.2 General block-based multicarrier model 3.2 Waveform processing techniques 3.2.1 Linear and circular filtering 3.2.2 Windowing 3.3 Structured representation 3.3.1 Modulator 3.3.2 Demodulator 3.3.3 MIMO Waveform processing 3.4 Detection 3.4.1 Maximum-likelihood detection 3.4.2 Linear detection 3.4.3 Iterative Detection 3.4.4 Numerical example and insights 3.5 Summary 4 Generic Multiple Access Schemes 57 4.1 Basic multiple access and multiplexing schemes 4.1.1 Infrastructure network system model 4.1.2 Duplex schemes 4.1.3 Common multiplexing and multiple access schemes 4.2 General multicarrier-based multiple access 4.2.1 Design with fixed set of pulses 4.2.2 Computational model 4.2.3 Asynchronous multiple access 4.3 Summary 5 Time-Frequency Analyses of Multicarrier 5.1 General time-frequency representation 5.1.1 Block representation 5.1.2 Relation to Zak transform 5.2 Time-frequency spreading 5.3 Time-frequency block in LTV channel 5.3.1 Subcarrier and subsymbol numerology 5.3.2 Processing based on the time-domain signal 5.3.3 Processing based on the frequency-domain signal 5.3.4 Unified signal model 5.4 summary 6 Generalized waveforms based on time-frequency shifts 6.1 General time-frequency shift 6.1.1 Time-frequency shift design 6.1.2 Relation between the shifted pulses 6.2 Time-frequency shift in Gabor frame 6.2.1 Conventional GFDM 6.3 GFDM modulation 6.3.1 Filter bank representation 6.3.2 Block representation 6.3.3 GFDM matrix structure 6.3.4 GFDM demodulator 6.3.5 Alternative interpretation of GFDM 6.3.6 Orthogonal modulation and GFDM spreading 6.4 Summary 7 Modulation Framework: Architectures and Applications 7.1 Modem architectures 7.1.1 General modulation matrix structure 7.1.2 Run-time flexibility 7.1.3 Generic GFDM-based architecture 7.1.4 Flexible parallel multiplications architecture 7.1.5 MIMO waveform architecture 7.2 Extended GFDM framework 7.2.1 Architectures complexity and flexibility analysis 7.2.2 Number of multiplications 7.2.3 Hardware analysis 7.3 Applications of the extended GFDM framework 7.3.1 Generalized FDMA 7.3.2 Enchantment of OFDM system 7.4 Summary 7 Conclusions and Future work

OFDM based air interfaces for future mobile satellite systems

This thesis considers the performance of OFDM in a non-linear satellite channel and mechanisms for overcoming the degradations resulting from the high PAPR in the OFDM signal in the specific satellite architecture. It was motivated by new S-DMB applications but its results are applicable to any OFDM system via satellites. Despite many advantages of OFDM, higher PAPR is a major drawback. OFDM signals are therefore very sensitive to non-linear distortion introduced by the power amplifiers and thus, significantly reduce the power efficiency of the system, which is already crucial to satellite system economics. Simple power amplifier back-off to cope with high OFDM PAPR is not possible. Two transmitter based techniques have been considered: PAPR reduction and amplifier linearization.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Constant Envelope DCT- and FFT- based Multicarrier Systems

Discrete Cosine Transform (DCT)- and Fast Fourier Transform (FFT)- based Orthogonal Frequency Division Multiplexing (OFDM) systems with a variety of angle modulations are considered for data transmission. These modulations are used with the purpose of achieving Constant Envelope (CE) transmitted signals, for superior power efficiency with nonlinear High Power Amplifier (HPA), typically used at the transmitter in OFDM systems. Specifically, four angle modulations are considered: i) Phase Modulation (PM); ii) Frequency Modulation (FM); iii) Continuous Phase Modulation (CPM); and iv) Continuous Phase Chirp Modulation (CPCM). Descriptions of DCT- and FFT- based OFDM systems with M-ary Pulse Amplitude Modulation (MPAM) mapper, with these modulations, are given and expressions for transmitted signals are developed. The detection of these signals in Additive White Gaussian Noise (AWGN) and multipath fading channels is addressed. The receiver structure consists of arctangent demodulator followed by the optimum OFDM receiver for memoryless PM and FM modulations. However, for CPM and CPCM modulations that have inherent memory, arctangent demodulator followed by correction with oversampling technique is used prior to the optimum OFDM receiver. Closed-form expressions for Bit Error Rate (BER) have been derived and are function of: i) Signal-to-Noise Ratio, (Eb/N0); ii) Modulation parameters; iii) Number of amplitude levels of M-PAM mapper; and iv) parameters of multipath fading environment. It is shown that, in general, BER performance of CE-DCT-OFDM system is superior compared to that of conventional DCT-OFDM system, when the effect of HPA in the system is taken into account. Also, it is observed that CE-DCT-OFDM system outperforms CE-FFT-OFDM system by nearly 3 dB. The DCT- and FFT- OFDM systems with CPM and CPCM modulations are superior in BER performance compared to PM and FM modulations in these systems. The use of CPCM in OFDM systems can provide attractive trade off between bandwidth and BER performance. The performance of CE-DCT-OFDM and CE-FFT-OFDM systems over Rayleigh and Rician frequency non-selective slowly-varying fading channels are illustrated as a function of channel parameters and the penalty in SNR that must be paid as consequence of the fading is determined

D13.1 Fundamental issues on energy- and bandwidth-efficient communications and networking

Deliverable D13.1 del projecte europeu NEWCOM#The report presents the current status in the research area of energy- and bandwidth-efficient communications and networking and highlights the fundamental issues still open for further investigation. Furthermore, the report presents the Joint Research Activities (JRAs) which will be performed within WP1.3. For each activity there is the description, the identification of the adherence with the identified fundamental open issues, a presentation of the initial results, and a roadmap for the planned joint research work in each topic.Preprin