Dielectric Spectroscopy of Biological Samples

For the first time, the impedance spectrum of live Jurkat T-lymphocytes human cells was characterized in a single sweep spanning six decades of frequency from 9 kHz to 9 GHz. The ultrawide bandwidth bridged the traditional impedance spectroscopy at kilohertz to megahertz frequencies with the recently developed microwave dielectric spectroscopy, which can probe the cell interior without being hindered by the cell membrane. Based on the measured scattering parameters and a simple cell model, an equivalent circuit of four nondispersive elements, including membrane resistance, membrane capacitance, cytoplasm resistance, and cytoplasm capacitance, was extracted and found sufficient to explain the so-called β relaxation over the frequencies measured. The extracted cell parameters were in general agreement with the literature. However, the presently extracted membrane capacitance of 0.4 pF and cytoplasm resistance of 0.75 MΩ are on the low and high end of the literature, respectively. This could be explained by having separated out the shunt effects of the membrane resistance and cytoplasm capacitance, respectively. In fact, the present membrane resistance and cytoplasm capacitance, at 2.8 MΩ and 10 fF, respectively, are believed to be more reliable due to the low-conductivity solution and the microwave frequency used. Meanwhile, sensitivity analysis was carried out for extracting lumped cell characteristics such as membrane resistance and cytoplasm capacitance from the scattering parameters. The scattering parameters were measured on a coplanar waveguide with a Jurkat cell trapped by dielectrophoresis either in a series or shunt configuration. The sensitivity analysis validated our previous empirical observation that the insertion loss of a series-trapped cell and the return loss of a shunt-trapped cell were most sensitive to the cell impedance. Additionally, the membrane resistance and cytoplasm capacitance were most sensitive to low- and high-frequency scattering parameters, respectively. Furthermore, the dissertation presents a novel in situ single-connection calibration using biocompatible solutions, which is demonstrated in single-cell characterization from 0.5 GHz to 9 GHz for the first time as well. The characterization is based on quickly trapping and detrapping the cell by dielectrophoresis on a coplanar waveguide (CPW) with a small protrusion in one of its ground electrodes, which doubles as the calibration standard when covered by different liquids. Consistent with theoretical analysis, the difference in the transmission coefficient increases with increasing frequency and is generally smaller than the difference in the reflection coefficient. With improved accuracy and throughput, the calibration technique may enable broadband electrical characterization of single cells in a high-speed cytometer

Tailor-Made Tissue Phantoms Based on Acetonitrile Solutions for Microwave Applications up to 18 GHz

(c) 2016 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.Tissue-equivalent phantoms play a key role in the development of new wireless communication devices that are tested on such phantoms prior to their commercialization. However, existing phantoms cover a small number of tissues and do not reproduce them accurately within wide frequency bands. This paper aims at enlarging the number of mimicked tissues as well as their working frequency band. Thus, a variety of potential compounds are scanned according to their relative permittivity from 0.5 to 18 GHz. Next, a combination of these compounds is characterized so the relation between their dielectric properties and composition is provided. Finally, taking advantage of the previous analysis, tailor-made phantoms are developed for different human tissues up to 18 GHz and particularized for the main current body area network (BAN) operating bands. The tailor-made phantoms presented here exhibit such a high accuracy as would allow researchers and manufacturers to test microwave devices at high frequencies for large bandwidths as well as the use of heterogeneous phantoms in the near future. The key to these phantoms lies in the incorporation of acetonitrile to aqueous solutions. Such compounds have a suitable behavior to achieve the relative permittivity values of body tissues within the studied frequency band.This work was supported by the Ministerio de Economia y Competitividad, Spain (TEC2014-60258-C2-1-R) and by the European FEDER Funds.Castelló-Palacios, S.; García Pardo, C.; Fornés Leal, A.; Cardona Marcet, N.; Vallés Lluch, A. (2016). Tailor-Made Tissue Phantoms Based on Acetonitrile Solutions for Microwave Applications up to 18 GHz. IEEE Transactions on Microwave Theory and Techniques. 64(11):3987-3994. https://doi.org/10.1109/TMTT.2016.2608890S39873994641

Developing Novel 3D Antennas Using Advanced Additive Manufacturing Technology

In today’s world of wireless communication systems, antenna engineering is rapidly advancing as the wireless services continue to expand in support of emerging commercial applications. Antennas play a key role in the performance of advanced transceiver systems where they serve to convert electric power to electromagnetic waves and vice versa. Researchers have held significant interest in developing this crucial component for wireless communication systems by employing a variety of design techniques. In the past few years, demands for electrically small antennas continues to increase, particularly among portable and mobile wireless devices, medical electronics and aerospace systems. This trend toward smaller electronic devices makes the three dimensional (3D) antennas very appealing, since they can be designed in a way to use every available space inside the devise. Additive Manufacturing (AM) method could help to find great solutions for the antennas design for next generation of wireless communication systems. In this thesis, the design and fabrication of 3D printed antennas using AM technology is studied. To demonstrate this application of AM, different types of antennas structures have been designed and fabricated using various manufacturing processes. This thesis studies, for the first time, embedded conductive 3D printed antennas using PolyLactic Acid (PLA) and Acrylonitrile Butadiene Styrene (ABS) for substrate parts and high temperature carbon paste for conductive parts which can be a good candidate to overcome the limitations of direct printing on 3D surfaces that is the most popular method to fabricate conductive parts of the antennas. This thesis also studies, for the first time, the fabrication of antennas with 3D printed conductive parts which can contribute to the new generation of 3D printed antennas

The measurement of the dielectric constant of concrete pipes and clay pipes

To optimize the effectiveness of the rehabilitation of underground utilities, taking in consideration limitation of available resources, there is a need for a cost effective and efficient sensing systems capable of providing effective, in real time and in situ, measurement of infrastructural characteristics. To carry out accurate non-destructive condition assessment of buried and above ground infrastructure such as sewers, bridges, pavements and dams, an advanced ultra-wideband (UWB) based radar was developed at Trenchless Technology Centre (TTC) and Centre for Applied Physics Studies (CAPS) at Louisiana Tech University (LTU). One of the major issues in designing the FCC compliant UWB radar was the contribution of the pipe wall, presence of complex soil types and moderate-to-high moisture levels on penetration depth of the electromagnetic (EM) energy. The electrical properties of the materials involved in designing the UWB radar exhibit a significant variation as a result of the moisture content, mineral content, bulk density, temperature and frequency of the electromagnetic signal propagating through it. Since no measurements of frequency dependence of the dielectric permittivity and conductivities of the pipe wall material in the FCC approved frequency range exist, in this thesis, the dielectric constant of concrete and clay pipes are measured over a microwave frequency range from 1 Ghz to 10 Ghz including the effects of moisture and chloride content. A high performance software package called MU-EPSLN™ was used for the calculations. Data reduction routines to calculate the complex permeability and permittivity of materials as well as other parameters are also provided. The results obtained in this work will be used to improve the accuracy of the numerical simulations and the performances of the UWB radar system

Signals in the Soil: An Introduction to Wireless Underground Communications

In this chapter, wireless underground (UG) communications are introduced. A detailed overview of WUC is given. A comprehensive review of research challenges in WUC is presented. The evolution of underground wireless is also discussed. Moreover, different component of UG communications is wireless. The WUC system architecture is explained with a detailed discussion of the anatomy of an underground mote. The examples of UG wireless communication systems are explored. Furthermore, the differences of UG wireless and over-the-air wireless are debated. Different types of wireless underground channel (e.g., In-Soil, Soil-to-Air, and Air-to-Soil) are reported as well

In situ underwater microwave oil spill and oil slick thickness sensor

Nearly 30 percent of oil drilled globally is done offshore. Oil spillage offshore have far-reaching consequences on the environment, aquatic lives, and livelihoods as it was evident in the numerous accidents such as the Deepwater Horizon and Bonga oil spillages. Apart from detecting oil spillages, the determination of the oil slick thickness is very important. This is to enable the estimation of the volume and spread of oil discharged in oceans, seas and lakes. This information could guide the oil spill countermeasures and provide the basis for legal actions against the defaulting parties. The viability of the use of radar in the detection of oil spill has already been established by airborne and space borne synthetic aperture radar (SAR). Notwithstanding, the high latency associated with SARs and its susceptibility of false positive and false negative detection of oil slick makes it vulnerable. It has also not been very successful in the determination of oil slick thickness. In situ methods such as the capacitive, conductive and optical based approaches have been used to detect as well as determine oil slick thickness. Some of these contact-based approaches are susceptible to corrosion, fouling and require several calibrations. Radio frequency (RF) signals in seawater suffer from attenuation and dispersion due to the high conductivity of the medium. Antennas, ideally matched to free space, suffer impedance mismatches when immersed in seawater. In this thesis, we proposed the novel approach of using microwave techniques to detect oil spillage and determine oil slick thickness based on a contact-based in situ approach. The work began by undertaking an investigation into the properties of the North Sea water which was used as the primary transmission medium for the study. Subsequently, the research developed an ultrawideband antenna that radiated underwater, which was encapsulated in polydimethylsiloxane (PDMS). The antenna-sensor with a Faraday cage was used to develop a novel microwave oil spill sensor. A communication backbone was designed for the sensor using long range (LoRa) 868 MHz frequency based on a bespoke braid antenna buffered by oil impregnated papers to ameliorate against the influence of the seawater surface. Using a four layered RF switch controller and an antenna array consisting of four antenna-sensors, a novel microwave oil slick thickness sensor was developed. The antenna-sensors were arranged in a cuboid fashion with antenna-sensor 3 and antenna-sensor 4 capable of detecting oil slick thickness at 23 mm and 46 mm using their transmission coefficient (S43) of -10 dB and -19 dB compared to that of the pure seawater respectively. For the 69 mm and 92 mm thickness, the transmission coefficient (S21) of antenna-sensor 1 and antenna-sensor 2 was used to determine these thicknesses with values of -13.5 dB and -24.14 dB with respect to that of pure seawater

Dielectric Characterization of Biological Tissues for Medical Applications

[ES] Conocer las propiedades electromagnéticas de los tejidos biológicos con la mayor exactitud posible tiene una gran importancia en el diseño de un elevado número de aplicaciones biomédicas. El diseño de dispositivos médicos inalámbricos, antenas superficiales e intracorporales, evaluación de tasas de absorción electromagnética, técnicas de tratamiento y detección de cáncer como la hipertermia e imágenes médicas son ejemplos de aplicaciones que requieren esta información para su desarrollo. Debido a que el cáncer provoca modificaciones estructurales en las células que a su vez generan cambios en las propiedades electromagnéticas, es posible desarrollar aplicaciones de detección de cáncer que se basen en este hecho. Un objetivo potencial es el cáncer de colon (CRC), debido a que los tejidos de colon sospechosos son accesibles de forma más o menos sencilla durante procedimientos endoscópicos. Este tipo de cáncer es uno de los más extendidos, siendo responsable de aproximadamente el 10% de casos y muertes totales. Existe un gran número de factores de riesgo que pueden explicar la aparición de la enfermedad, aunque esencialmente la probabilidad se incrementa significativamente con el aumento de la edad de la población. Los programas de cribado sobre la población son críticos: si el cáncer se detecta en etapas tempranas, la probabilidad de sobrevivir se incrementa en gran medida, y además se reducen los costes asociados. Uno de los objetivos principales de esta tesis es proponer aplicaciones que ayuden en la detección de CRC durante la colonoscopia haciendo uso de las diferencias en las propiedades electromagnéticas. Aparte de mejoras en el diagnóstico, complementar la colonoscopia puede conllevar otros beneficios colaterales como una reducción en la carga de anatomía patológica. Para demostrar la viabilidad y el potencial desarrollo futuro de estas aplicaciones, en esta tesis se miden y se trata de encontrar diferencias entre las propiedades electromagnéticas de tejidos sanos, cancerosos y patológicos de colon humano. Las medidas han sido llevadas a cabo mediante la técnica del coaxial terminado en abierto. Con el propósito de incrementar la precisión del método, se ha evaluado el principio de funcionamiento y se ha mejorado el proceso de calibración. Dos fuentes de tejido de colon han sido analizadas en esta tesis: tejidos procedentes de colonoscopias (biopsias) y tejidos obtenidos a partir de procedimientos quirúrgicos. Aparte de tejido sano, se estudian las siguientes patologías: Adenocarcinomas (CRC), adenomas sin displasia, adenomas con bajo grado de displasia, adenomas con alto grado de displasia, hiperplasias y hamartomas. Debido a la alta variabilidad entre distintos sujetos, las propiedades electromagnéticas de los tejidos sospechosos de un paciente en concreto deben ser siempre comparadas con las propiedades de sus tejidos sanos, no evaluadas de forma independiente. El segundo gran objetivo de esta tesis es el desarrollo de una nueva base de datos de las propiedades electromagnéticas de tejidos biológicos medidas in vivo. Ahora mismo, las colecciones disponibles están limitadas en número de tejidos o frecuencias caracterizadas, obligando a los investigadores a escoger bases de datos más completas pero realizadas ex vivo. No obstante, usar este tipo de colecciones tienen fuentes de incertidumbre adicionales dado que las medidas están condicionadas por la deshidratación de los tejidos y la perdida de flujo sanguíneo. El desarrollo de esta nueva base de datos puede facilitar el diseño de aplicaciones que requieran conocer las propiedades electromagnéticas con alto grado de precisión.[CA] Conéixer les propietats electromagnètiques dels teixits biològics amb la major exactitud possible té una gran importància en el disseny d'un gran nombre d'aplicacions biomèdiques. El disseny de dispositius metges sense fil, antenes superficials i intracorporales, l'avaluació de taxes d'absorció electromagnètica, tècniques de tractament i detecció de càncer com ara la hipertèrmia i imatges mediques són exemples d'aplicacions que requerixen esta informació. Com el càncer provoca modificacions estructurals en les cèl·lules que generen canvis en les propietats electromagnètiques, es possible desenrotllar aplicacions de detecció de càncer que es basen en este fet. Un objectiu potencial és el càncer de colon (CRC), pel fet que els teixits de colon sospitosos són accessibles de forma més o menys senzilla durant procediments endoscòpics. Este tipus de càncer és un dels més estesos, sent responsable d'aproximadament el 10% de casos i morts totals. N'hi ha un gran nombre de factors de risc que poden explicar l'aparició de la malaltia, encara que en resum la probabilitat s'incrementa significativament amb l'augment de l'edat de la població. Els programes de cribratge sobre la població són crítics. Si el càncer es detecta en etapes primerenques, la probabilitat de sobreviure s'incrementa en gran manera, i a més es reduïxen els costos associats. Un dels objectius principals d'esta tesi és proposar aplicacions que ajuden en la detecció de CRC durant la colonoscòpia fent ús de les diferències en les propietats electromagnètiques. A banda de millores en el diagnòstic, complementar la colonoscòpia pot comportar altres beneficis col·laterals com una reducció en la càrrega d'anatomia patològica. Per a demostrar la fiabilitat i el potencial desenrotllament d'aquestes aplicacions, en aquesta tesi es mesuren i es tracta de trobar diferències entre les propietats electromagnètiques de teixits sans, cancerosos i patològics de colon humà. Les mesures han sigut realitzades mitjançant la tècnica del coaxial acabat en obert. Amb el propòsit d'incrementar la precisió del mètode, s'ha avaluat el seu principi de funcionament i s'ha millorat el procés de calibratge. Dos fonts de teixit de colon s'han analitzat en aquesta tesi: teixits procedents de colonoscòpies (biòpsies) i teixits obtinguts a partir de procediments quirúrgics. Apart de teixit sà, s'estudien els següents teixits: Adenocarcinomes (CRC), adenomes sense displàsia, adenomes amb baix grau de displàsia, adenomes amb alt grau de displàsia, hiperplàsies y hamartomes. Degut a l'alta variabilitat entre diferents subjectes, les propietats electromagnètiques dels teixits sospitosos d'un pacient en particular han de ser comparades amb les propietats dels seus teixits sans, no avaluats independentment. El segon gran objectiu d'esta tesi és el desenrotllament d'una nova base de dades de les propietats electromagnètiques de teixits biològics mesurades in vivo. Ara mateix, les col·leccions disponibles estan limitades en nombre de teixits o freqüències caracteritzades, obligant els investigadors a triar bases de dades més completes però realitzades ex vivo. No obstant això, este tipus de col·leccions te fonts d'incertesa addicionals atés que les mesures estan condicionades per la deshidratació dels teixits i la pèrdua de flux sanguini. El desenrotllament d'esta nova base de dades pot facilitar el disseny d'aplicacions que requerisquen conéixer les propietats electromagnètiques amb alt grau de precisió.[EN] Nowadays, a careful knowledge of the electromagnetic properties of biological tissues is required for developing a great number of applications. The development of wireless medical devices, the design of in-body and on-body antennas, specific absorption rate evaluations, cancer treatment techniques such as hyperthermia and detection techniques like medical imaging are some examples of applications that rely on these data. Since cancer causes modifications on the biological structure of cells that can lead in turn to changes in the electromagnetic properties of the tissues, it is possible to develop novel detection applications taking advantage of it. One potential target is colorectal cancer (CRC), as suspicious tissues can be accessed quite easily through colonoscopy procedures. This kind of cancer is one of the most spread kinds, being responsible of about 1 out of 10 new cancer cases and deaths. There are several risk factors currently related to the apprising of this cancer, although in essence the higher the age of the population, the higher the incidence of CRC. Screening programs are key for detecting and diagnosing cancer: if found at early stages, the probability of survival increases greatly, and the cost of the treatment can be reduced as well. One of the major objectives of this dissertation is proposing applications for detecting CRC that aid in the colonoscopy procedures by making use of the differences in electromagnetic properties. Aside from enhancement in the diagnosis of CRC, improving the colonoscopy procedure can lead to collateral benefits like a lowering of the burden of anatomical pathology unit. With the aim at demonstrating the feasibility and the potential future development of these applications, in the framework of this thesis the dielectric properties of healthy, cancerous and pathological human colon tissues are measured and compared in order to find electromagnetic differences. Measurements are carried out by means of an open-ended coaxial system. Its principle of operation has been revisited with the aim at maximizing the accuracy of the method, and the calibration procedure has been optimized serving the same purpose. Two main sources of colon tissue have been analyzed: samples from colonoscopy biopsies and samples from surgery resections. Besides healthy tissue, the following colon tissues have been characterized: Adenocarcinomas (CRC), adenomas without dysplasia, adenomas with low-grade dysplasia, adenomas with high-grade dysplasia, hyperplastic polyps and hamartomatous polyps. Given the variability that can appear among subjects, the electromagnetic properties of suspicious tissues from a particular patient have to be always compared with those of his healthy ones, not evaluated independently. The second major objective of this thesis involves the development of a new database of electromagnetic properties of biological tissues obtained at in vivo conditions. Nowadays, the available collections are limited either in the number of tissues or the measured frequencies, and hence researchers have to make use of more complete databases but that were performed ex vivo. The drawback of using these collections is that results can be compromised by factors such as lack of blood perfusion and tissue dehydration. Developing this new database can facilitate the design of applications that needs of a careful knowledge of these properties.Fornés Leal, A. (2019). Dielectric Characterization of Biological Tissues for Medical Applications [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/132188TESI

Evaluating a breast tumor monitoring vest with flexible UWB antennas and realistic phantoms:a proof-of-concept study

Abstract. The introduction provides an overview of the global significance of breast cancer as a health concern and the limitations of existing breast cancer screening methods. It introduces the concept of microwave-based breast cancer monitoring and highlights the promising findings from a previous research paper. The objective of the master thesis is presented, which is to develop and evaluate a self-monitoring vest equipped with UWB antennas and channel analysis to overcome the limitations of current screening methods and enable regular breast cancer monitoring from home. The "Background and Literature Review," provides a comprehensive overview of the relevant topics related to microwave techniques for breast cancer detection. It starts by discussing the anatomy of the female breast, highlighting the importance of understanding its structure for effective tumor detection. The section then delves into the microwave properties of the human breast, elucidating the interactions between microwaves and breast tissue. The basic principle of microwave channel analysis is explained, emphasizing its significance in detecting breast tumors. Furthermore, the advantages of microwave-based tumor detection methods are explored, showcasing their potential for improved breast cancer screening. Various microwave techniques used in breast cancer detection, including microwave tomography and radar-based UWB microwave imaging, are discussed, along with different self-monitoring vests integrated with UWB antennas. This section serves as a foundation for the subsequent chapters of the thesis, providing a comprehensive background and literature review to support the research and development of the practical self-monitoring vest for early detection of small-sized breast tumors. The "Preparation of Tissue Phantoms" section in the master’s thesis explores the comprehensive methodology for creating tissue phantoms that replicate the dielectric properties of various human tissues. While the section primarily focuses on fat tissue, it also acknowledges the existence of other phantom types. The outlined approach involves careful ingredient selection, formulation development, fabrication techniques, and stability evaluation for the creation of skin, muscle, fat, tumor, and gland tissue phantoms. By following these procedures, researchers can successfully produce tissue phantoms that closely mimic the properties of real human tissues. These phantoms serve as essential tools for investigating microwave-based applications in medical diagnostics and provide a reliable and versatile platform for further research in the field. The third section discusses the assembly of heterogeneous breast phantoms used for evaluating the performance of the tumor detection vest. The phantoms consisted of outer and inner molds, with the outer molds resembling the shape of a prone human breast. Two breast density types, representing very dense and less dense breasts, were used. For the dense breast phantoms, liquid fat material was solidified in the outer molds, and a glandular liquid was poured into the inner mold, with tumors inserted and covered with additional glandular liquid. For the less dense breast phantoms, fat liquid was solidified in the outer molds, and cylindrical glandular molds were inserted. A skin layer and muscle layer were added to complete the assembly, accurately simulating the composition and structure of a breast. This realistic breast phantom assembly allowed for accurate measurements and evaluation of the vest’s performance under different breast density conditions, contributing to breast imaging research and development. The "Monitoring Vest" section discusses the antennas used in the tumor detection vest and the design of two different vest versions. Antenna1 is a UWB monopole antenna with a flexible laminate substrate, while Antenna2 is a textile-based version of Antenna1. Antenna3 has a Kapton-based substrate and larger dimensions. The combination of these antennas ensures accurate tumor detection in various breast conditions. The section also highlights the measurement and comparison of the S11 parameter for the PCB antenna in free space and when placed on the skin, emphasizing the impact of the skin on antenna performance. The section concludes by describing the design of the vests, including the arrangement of pockets and the use of RF cables for connection. The careful design and implementation of the vests and antenna placement ensure accurate measurements and reliable performance evaluation. The results section of the study shows that the presence of tumors in breast tissue leads to a noticeable decrease in channel attenuation. The higher dielectric properties of tumors cause additional reflections and diffraction, affecting signal propagation within the breast. These changes in channel characteristics are influenced by factors such as tumor size, breast density, and antenna configuration. The study demonstrates the detectability of tumors and provides valuable insights for developing effective tumor detection systems in different breast tissue scenarios. In this master thesis, a prototype of a breast tumor monitoring vest utilizing UWB flexible antennas was developed and evaluated. The research demonstrated the effectiveness of the vest in detecting breast tumors, even as small as 1cm, by leveraging the distinct characteristics of radio channels among multiple on-body antennas embedded in the vest. Higher frequencies in the 7–8 GHz range showed improved resolution and contrast in relative permittivity, enhancing the accuracy of tumor detection. The development of tissue phantoms played a crucial role, enabling reliable experiments to mimic human tissues. Integration of advanced AI algorithms and 6G technology holds promise for enhancing diagnostic capabilities and revolutionizing healthcare. Overall, the breast tumor monitoring vest shows potential for widespread implementation in breast health checks, home monitoring, and wireless healthcare systems