Massive MIMO transmission techniques

Next generation of mobile communication systems must support astounding data traffic increases, higher data rates and lower latency, among other requirements. These requirements should be met while assuring energy efficiency for mobile devices and base stations. Several technologies are being proposed for 5G, but a consensus begins to emerge. Most likely, the future core 5G technologies will include massive MIMO (Multiple Input Multiple Output) and beamforming schemes operating in the millimeter wave spectrum. As soon as the millimeter wave propagation difficulties are overcome, the full potential of massive MIMO structures can be tapped. The present work proposes a new transmission system with bi-dimensional antenna arrays working at millimeter wave frequencies, where the multiple antenna configurations can be used to obtain very high gain and directive transmission in point to point communications. A combination of beamforming with a constellation shaping scheme is proposed, that enables good user isolation and protection against eavesdropping, while simultaneously assuring power efficient amplification of multi-level constellations

Transmitter Architectures Based on Near-Field Direct Antenna Modulation

A near-field direct antenna modulation (NFDAM) technique is introduced, where the radiated far-field signal is modulated by time-varying changes in the antenna near-field electromagnetic (EM) boundary conditions. This enables the transmitter to send data in a direction-dependent fashion producing a secure communication link. Near-field direct antenna modulation (NFDAM) can be performed by using either switches or varactors. Two fully-integrated proof-of-concept NFDAM transmitters operating at 60 GHz using switches and varactors are demonstrated in silicon proving the feasibility of this approach

Direct Antenna Modulation using Frequency Selective Surfaces

In the coming years, the number of connected wireless devices will increase dramatically, expanding the Internet of Things (IoT). It is likely that much of this capacity will come from network densification. However, base stations are inefficient and expensive, particularly the downlink transmitters. The main cause of this is the power amplifier (PA), which must amplify complex signals, so are expensive and often only 30% efficient. As such, the cost of densifying cellular networks is high. This thesis aims to overcome this problem through codesign of a low complexity, energy efficient transmitter through electromagnetic design; and a waveform which leverages the advantages and mitigates the disadvantages of the new technology, while being suitable for supporting IoT devices. Direct Antenna Modulation (DAM) is a low complexity transmitter architecture, where modulation occurs at the antenna at transmit power. This means a non-linear PA can efficiently amplify the carrier wave without added distortion. Frequency Selective Surfaces (FSS) are presented here as potential phase modulators for DAM transmitters. The theory of operation is discussed, and a prototype DAM for QPSK modulation is simulated, designed and tested. Next, the design process for a continuous phase modulating antenna is explored. Simulations and measurement are used to fully characterise a prototype, and it is implemented in a line-of-sight end-to-end communications system, demonstrating BPSK, QPSK and 8-PSK. Due to the favourable effects of spread spectrum signalling on FSS DAM performance, Cyclic Prefix Direct Sequence Spread Spectrum (CPDSSS) is developed. Conventional spreading techniques are extended using a cyclic prefix, making multipath interference entirely defined by the periodic autocorrelation of the sequence used. This is demonstrated analytically, through simulation and with experiments. Finally, CPDSSS is implemented using FSS DAM, demonstrating the potential of this new low cost, low complexity transmitter with CPDSSS as a scalable solution to IoT connectivity

Next generation optical access networks and coexistence with legacy PONs

Nowadays, Fiber-to-the-Home is one of the most promising solutions to provide broadband services in access networks. However, the fiber is inefficiently used as most of the deployed systems are still based on Time Division Multiplexing Passive Optical Networks (TDM-PONs) providing shared transmission capacities up to 2.5 Gb/s down and 1.25 Gb/s up, among multiple users. Research on high-speed electronics and Wavelength Division Multiplexing (WDM) has allowed the emergence of what is known as the second generation PON (NG-PON2), which specify aggregated capacities up to 40 Gb/s, stacking four channels at symmetric data rates of 10 Gb/s each, for residential scenarios. Nevertheless, the capacity per channel is still shared between multiple users due to the use of TDM. Moreover, the optical spectrum efficiency is low because channels are widely spaced (50 to 100 GHz). In addition, the sensitivity, reach and number of users is limited as consequence of using direct detection (DD) systems. In consequence, and due to the increase in bandwidth demands of new multimedia applications, it is necessary to propose solutions that cope with this tendency and, even more important, that can coexist with legacy systems, being one of the major requirements of network operators to guarantee a smooth and non-disruptive technology migration. In this thesis, a breakthrough technology such as Ultra-Dense WDM (UDWDM) that allows to allocate a large number of channels spaced only by a few GHz is used. This approach consent to envision the concept of Wavelength-to-the-User, where each costumer can be served with dedicated bandwidth links. The key technologies are based on coherent systems, with inherent wavelength selectivity and improved sensitivity compared to DD systems, thanks to the booster action of a tunable local oscillator (LO) laser. Because of cost is the main constraint in access networks, especially at the customer premises equipment (Optical Network Unit - ONU), in this thesis, a new class of coherent transceivers, based on low-cost direct modulated lasers and simplified receiver schemes, are proposed and experimentally tested. Moreover, the issue of coexistence is investigated through theoretical studies and real-time implementations, demonstrating full compatibility with legacy systems. Between the proposed solutions, a simple technique to adjust digitally the direct phase modulation of a distributed feedback (DFB) laser is presented to support flexible transmission rates. Next, several multilevel phase modulation formats for achieving higher transmission rates and better spectral efficiency are experimentally compared. Subsequently, the topic of photonic integration is addressed, demonstrating for the first time an 8-ary hybrid amplitude and phase modulated transmitter (Tx), by using a low-cost, small-footprint and energy efficient dual electro-absorption modulated laser (DEML). Finally, two novel proposals, to reduce the complexity of heterodyne and intradyne detection, are provided to face the typical issue of complexity and high-cost of coherent systems. The former explores the possibility of using only one DFB laser as LO and Tx at the ONU. The later demonstrates for the first time, a novel phase time diversity technique alternating phase modulation at each complex component (in-phase - I and quadrature - Q) achieving a 10 Gb/s' transmission with polarization independence.En la actualidad, la Fibra hasta el Hogar es una de las soluciones más prometedoras para proporcionar servicios de banda ancha en las redes de acceso. Sin embargo, la fibra se usa de manera poco eficiente, ya que la mayoría de los sistemas implementados todavía están basados en redes ópticas pasivas de multiplexación por división en el tiempo (TDM-PON) que brindan capacidades de transmisión compartidas entre múltiples usuarios de hasta 2.5 Gb/s y 1.25 Gb/s. La investigación en electrónica de alta velocidad y la multiplexación por división de longitud de onda (WDM) ha permitido el surgimiento de lo hoy se conoce como PON de segunda generación (NG-PON2), que especifica capacidades agregadas de hasta 40 Gb/s, apilando cuatro canales a velocidades de datos simétricas de 10 Gb/s cada uno, para escenarios residenciales. Sin embargo, la capacidad por canal todavía se comparte entre múltiples usuarios debido al uso de TDM. Además, la eficiencia en el uso del espectro óptico es baja porque los canales están muy separados (50 a 100 GHz). Asimismo, la sensibilidad, el alcance y el número de usuarios están limitados debido al uso de sistemas de detección directa. En consecuencia, y debido al aumento de las demandas de ancho de banda de las nuevas aplicaciones multimedia, es necesario proponer soluciones que respondan a esta tendencia y, lo que es más importante, que puedan coexistir con sistemas heredados, siendo uno de los principales requisitos de los operadores de red para garantizar una migración de tecnología fluida y sin interrupciones. En esta tesis, se utiliza una tecnología de vanguardia, como la multiplexación por división ultra densa de longitud de onda (UDWDM) que permite distribuir un gran número de canales espaciados solo por unos pocos GHz. Este enfoque permite vislumbrar el concepto de longitud de onda para el usuario, donde cada cliente puede usar enlaces de ancho de banda dedicados. Las tecnologías clave están basadas en los sistemas coherentes, con selectividad de longitud de onda inherente y sensibilidad mejorada en comparación con los sistemas de detección directa, gracias al efecto de amplificación óptica de un láser oscilador local (LO) sintonizable. Debido a que el costo es la principal restricción en las redes de acceso, especialmente del equipo en las instalaciones del cliente (unidad de red óptica - ONU), en ésta tesis, una nueva clase de transceptores coherentes, basados en láseres de bajo coste modulados directamente y esquemas de recepción simplificados, son propuestos y probados experimentalmente. Además, el problema de la coexistencia es investigado a través de estudios teóricos y experimentos en tiempo real, demostrando compatibilidad total con los sistemas heredados. Entre las soluciones propuestas, se presenta una técnica simple para ajustar digitalmente la modulación de fase directa de un láser de retroalimentación distribuida (DFB), y admitir velocidades de transmisión flexibles. Acto seguido, se comparan experimentalmente varios formatos multinivel de modulación de fase, para lograr tasas de transmisión más altas y una mejor eficiencia espectral. Posteriormente, se aborda el tema de la integración fotónica, demostrando por primera vez un transmisor (Tx) con modulación híbrida de fase y amplitud de ocho puntos, mediante el uso de un dispositivo pequeño, de bajo coste y eficiente energéticamente, como lo es el láser dual de electro-absorción modulada (DEML). Finalmente, se presentan dos propuestas novedosas para reducir la complejidad de la detección heterodina e intradina, afrontando el problema típico de la complejidad y alto coste de los sistemas coherentes. La primera explora la posibilidad de usar solo un láser DFB en la ONU, como LO y Tx. La segunda, demuestra por primera vez, una nueva técnica de diversidad fase en el tiempo, que alterna la modulación de fase en cada componente del plano complejo (fase-I y cuadratura-Q) logrando una transmisión de 10 Gb / s / λ con independencia de polarizaciónPostprint (published version

Deep Autoencoder-based Z-Interference Channels with Perfect and Imperfect CSI

A deep autoencoder (DAE)-based structure for endto-end communication over the two-user Z-interference channel (ZIC) with finite-alphabet inputs is designed in this paper. The proposed structure jointly optimizes the two encoder/decoder pairs and generates interference-aware constellations that dynamically adapt their shape based on interference intensity to minimize the bit error rate (BER). An in-phase/quadrature-phase (I/Q) power allocation layer is introduced in the DAE to guarantee an average power constraint and enable the architecture to generate constellations with nonuniform shapes. This brings further gain compared to standard uniform constellations such as quadrature amplitude modulation. The proposed structure is then extended to work with imperfect channel state information (CSI). The CSI imperfection due to both the estimation and quantization errors are examined. The performance of the DAEZIC is compared with two baseline methods, i.e., standard and rotated constellations. The proposed structure significantly enhances the performance of the ZIC both for the perfect and imperfect CSI. Simulation results show that the improvement is achieved in all interference regimes (weak, moderate, and strong) and consistently increases with the signal-to-noise ratio (SNR). For example, more than an order of magnitude BER reduction is obtained with respect to the most competitive conventional method at weak interference when SNR>15dB and two bits per symbol are transmitted. The improvements reach about two orders of magnitude when quantization error exists, indicating that the DAE-ZIC is more robust to the interference compared to the conventional methods.Comment: 13 pages, 13 figures, 2 tables. Accepted for publication in the IEEE Transactions on Communications. arXiv admin note: text overlap with arXiv:2303.0831

Next generation optical access networks and coexistence with legacy PONs

Nowadays, Fiber-to-the-Home is one of the most promising solutions to provide broadband services in access networks. However, the fiber is inefficiently used as most of the deployed systems are still based on Time Division Multiplexing Passive Optical Networks (TDM-PONs) providing shared transmission capacities up to 2.5 Gb/s down and 1.25 Gb/s up, among multiple users. Research on high-speed electronics and Wavelength Division Multiplexing (WDM) has allowed the emergence of what is known as the second generation PON (NG-PON2), which specify aggregated capacities up to 40 Gb/s, stacking four channels at symmetric data rates of 10 Gb/s each, for residential scenarios. Nevertheless, the capacity per channel is still shared between multiple users due to the use of TDM. Moreover, the optical spectrum efficiency is low because channels are widely spaced (50 to 100 GHz). In addition, the sensitivity, reach and number of users is limited as consequence of using direct detection (DD) systems. In consequence, and due to the increase in bandwidth demands of new multimedia applications, it is necessary to propose solutions that cope with this tendency and, even more important, that can coexist with legacy systems, being one of the major requirements of network operators to guarantee a smooth and non-disruptive technology migration. In this thesis, a breakthrough technology such as Ultra-Dense WDM (UDWDM) that allows to allocate a large number of channels spaced only by a few GHz is used. This approach consent to envision the concept of Wavelength-to-the-User, where each costumer can be served with dedicated bandwidth links. The key technologies are based on coherent systems, with inherent wavelength selectivity and improved sensitivity compared to DD systems, thanks to the booster action of a tunable local oscillator (LO) laser. Because of cost is the main constraint in access networks, especially at the customer premises equipment (Optical Network Unit - ONU), in this thesis, a new class of coherent transceivers, based on low-cost direct modulated lasers and simplified receiver schemes, are proposed and experimentally tested. Moreover, the issue of coexistence is investigated through theoretical studies and real-time implementations, demonstrating full compatibility with legacy systems. Between the proposed solutions, a simple technique to adjust digitally the direct phase modulation of a distributed feedback (DFB) laser is presented to support flexible transmission rates. Next, several multilevel phase modulation formats for achieving higher transmission rates and better spectral efficiency are experimentally compared. Subsequently, the topic of photonic integration is addressed, demonstrating for the first time an 8-ary hybrid amplitude and phase modulated transmitter (Tx), by using a low-cost, small-footprint and energy efficient dual electro-absorption modulated laser (DEML). Finally, two novel proposals, to reduce the complexity of heterodyne and intradyne detection, are provided to face the typical issue of complexity and high-cost of coherent systems. The former explores the possibility of using only one DFB laser as LO and Tx at the ONU. The later demonstrates for the first time, a novel phase time diversity technique alternating phase modulation at each complex component (in-phase - I and quadrature - Q) achieving a 10 Gb/s' transmission with polarization independence.En la actualidad, la Fibra hasta el Hogar es una de las soluciones más prometedoras para proporcionar servicios de banda ancha en las redes de acceso. Sin embargo, la fibra se usa de manera poco eficiente, ya que la mayoría de los sistemas implementados todavía están basados en redes ópticas pasivas de multiplexación por división en el tiempo (TDM-PON) que brindan capacidades de transmisión compartidas entre múltiples usuarios de hasta 2.5 Gb/s y 1.25 Gb/s. La investigación en electrónica de alta velocidad y la multiplexación por división de longitud de onda (WDM) ha permitido el surgimiento de lo hoy se conoce como PON de segunda generación (NG-PON2), que especifica capacidades agregadas de hasta 40 Gb/s, apilando cuatro canales a velocidades de datos simétricas de 10 Gb/s cada uno, para escenarios residenciales. Sin embargo, la capacidad por canal todavía se comparte entre múltiples usuarios debido al uso de TDM. Además, la eficiencia en el uso del espectro óptico es baja porque los canales están muy separados (50 a 100 GHz). Asimismo, la sensibilidad, el alcance y el número de usuarios están limitados debido al uso de sistemas de detección directa. En consecuencia, y debido al aumento de las demandas de ancho de banda de las nuevas aplicaciones multimedia, es necesario proponer soluciones que respondan a esta tendencia y, lo que es más importante, que puedan coexistir con sistemas heredados, siendo uno de los principales requisitos de los operadores de red para garantizar una migración de tecnología fluida y sin interrupciones. En esta tesis, se utiliza una tecnología de vanguardia, como la multiplexación por división ultra densa de longitud de onda (UDWDM) que permite distribuir un gran número de canales espaciados solo por unos pocos GHz. Este enfoque permite vislumbrar el concepto de longitud de onda para el usuario, donde cada cliente puede usar enlaces de ancho de banda dedicados. Las tecnologías clave están basadas en los sistemas coherentes, con selectividad de longitud de onda inherente y sensibilidad mejorada en comparación con los sistemas de detección directa, gracias al efecto de amplificación óptica de un láser oscilador local (LO) sintonizable. Debido a que el costo es la principal restricción en las redes de acceso, especialmente del equipo en las instalaciones del cliente (unidad de red óptica - ONU), en ésta tesis, una nueva clase de transceptores coherentes, basados en láseres de bajo coste modulados directamente y esquemas de recepción simplificados, son propuestos y probados experimentalmente. Además, el problema de la coexistencia es investigado a través de estudios teóricos y experimentos en tiempo real, demostrando compatibilidad total con los sistemas heredados. Entre las soluciones propuestas, se presenta una técnica simple para ajustar digitalmente la modulación de fase directa de un láser de retroalimentación distribuida (DFB), y admitir velocidades de transmisión flexibles. Acto seguido, se comparan experimentalmente varios formatos multinivel de modulación de fase, para lograr tasas de transmisión más altas y una mejor eficiencia espectral. Posteriormente, se aborda el tema de la integración fotónica, demostrando por primera vez un transmisor (Tx) con modulación híbrida de fase y amplitud de ocho puntos, mediante el uso de un dispositivo pequeño, de bajo coste y eficiente energéticamente, como lo es el láser dual de electro-absorción modulada (DEML). Finalmente, se presentan dos propuestas novedosas para reducir la complejidad de la detección heterodina e intradina, afrontando el problema típico de la complejidad y alto coste de los sistemas coherentes. La primera explora la posibilidad de usar solo un láser DFB en la ONU, como LO y Tx. La segunda, demuestra por primera vez, una nueva técnica de diversidad fase en el tiempo, que alterna la modulación de fase en cada componente del plano complejo (fase-I y cuadratura-Q) logrando una transmisión de 10 Gb / s / λ con independencia de polarizació

A Cooperative Spectrum Sensing Network with Signal Classification Capabilities

This report describes the design and implementation of the spectrum sensing and signal classification sub-systems of a cooperative network. A sensor blindly receives and calculates the cyclic statistics of a signal decides whether or not the signal represents information or noise. If the signal\u27s statistics indicate the presence of data, the system attempts to classify its modulation scheme. Finally, the decisions of several independent sensors are combined to provide a reliable estimate of the contents of the spectrum of interest. Independently, sensors correctly classify a signal about 60-70% of the time in a low SNR environment. The data fusion module improves this number significantly - especially as the number of sensors increases

Cooperative communication in wireless networks: algorithms, protocols and systems

Current wireless network solutions are based on a link abstraction where a single co-channel transmitter transmits in any time duration. This model severely limits the performance that can be obtained from the network. Being inherently an extension of a wired network model, this model is also incapable of handling the unique challenges that arise in a wireless medium. The prevailing theme of this research is to explore wireless link abstractions that incorporate the broadcast and space-time varying nature of the wireless channel. Recently, a new paradigm for wireless networks which uses the idea of 'cooperative transmissions' (CT) has garnered significant attention. Unlike current approaches where a single transmitter transmits at a time in any channel, with CT, multiple transmitters transmit concurrently after appropriately encoding their transmissions. While the physical layer mechanisms for CT have been well studied, the higher layer applicability of CT has been relatively unexplored. In this work, we show that when wireless links use CT, several network performance metrics such as aggregate throughput, security and spatial reuse can be improved significantly compared to the current state of the art. In this context, our first contribution is Aegis, a framework for securing wireless networks against eavesdropping which uses CT with intelligent scheduling and coding in Wireless Local Area networks. The second contribution is Symbiotic Coding, an approach to encode information such that successful reception is possible even upon collisions. The third contribution is Proteus, a routing protocol that improves aggregate throughput in multi-hop networks by leveraging CT to adapt the rate and range of links in a flow. Finally, we also explore the practical aspects of realizing CT using real systems.PhDCommittee Chair: Sivakumar, Raghupathy; Committee Member: Ammar, Mostafa; Committee Member: Ingram, Mary Ann; Committee Member: Jayant, Nikil; Committee Member: Riley, Georg

Reconfigurable Intelligent Surfaces for Smart Cities: Research Challenges and Opportunities

The concept of Smart Cities has been introduced as a way to benefit from the digitization of various ecosystems at a city level. To support this concept, future communication networks need to be carefully designed with respect to the city infrastructure and utilization of resources. Recently, the idea of 'smart' environment, which takes advantage of the infrastructure for better performance of wireless networks, has been proposed. This idea is aligned with the recent advances in design of reconfigurable intelligent surfaces (RISs), which are planar structures with the capability to reflect impinging electromagnetic waves toward preferred directions. Thus, RISs are expected to provide the necessary flexibility for the design of the 'smart' communication environment, which can be optimally shaped to enable cost- and energy-efficient signal transmissions where needed. Upon deployment of RISs, the ecosystem of the Smart Cities would become even more controllable and adaptable, which would subsequently ease the implementation of future communication networks in urban areas and boost the interconnection among private households and public services. In this paper, we describe our vision of the application of RISs in future Smart Cities. In particular, the research challenges and opportunities are addressed. The contribution paves the road to a systematic design of RIS-assisted communication networks for Smart Cities in the years to come.Comment: Submitted for possible publication in IEEE Open Journal of the Communications Societ