Design and Validation of Network-on-Chip Architectures for the Next Generation of Multi-synchronous, Reliable, and Reconfigurable Embedded Systems

NETWORK-ON-CHIP (NoC) design is today at a crossroad. On one hand, the design principles to efficiently implement interconnection networks in the resource-constrained on-chip setting have stabilized. On the other hand, the requirements on embedded system design are far from stabilizing. Embedded systems are composed by assembling together heterogeneous components featuring differentiated operating speeds and ad-hoc counter measures must be adopted to bridge frequency domains. Moreover, an unmistakable trend toward enhanced reconfigurability is clearly underway due to the increasing complexity of applications. At the same time, the technology effect is manyfold since it provides unprecedented levels of system integration but it also brings new severe constraints to the forefront: power budget restrictions, overheating concerns, circuit delay and power variability, permanent fault, increased probability of transient faults. Supporting different degrees of reconfigurability and flexibility in the parallel hardware platform cannot be however achieved with the incremental evolution of current design techniques, but requires a disruptive approach and a major increase in complexity. In addition, new reliability challenges cannot be solved by using traditional fault tolerance techniques alone but the reliability approach must be also part of the overall reconfiguration methodology. In this thesis we take on the challenge of engineering a NoC architectures for the next generation systems and we provide design methods able to overcome the conventional way of implementing multi-synchronous, reliable and reconfigurable NoC. Our analysis is not only limited to research novel approaches to the specific challenges of the NoC architecture but we also co-design the solutions in a single integrated framework. Interdependencies between different NoC features are detected ahead of time and we finally avoid the engineering of highly optimized solutions to specific problems that however coexist inefficiently together in the final NoC architecture. To conclude, a silicon implementation by means of a testchip tape-out and a prototype on a FPGA board validate the feasibility and effectivenes

Design for Testability in a SerDes System

Testing an IC after fabrication helps ensure chip functionality. The techniques that consider the creation and utilization of tests inside the design flow are called Design for Testability. The present work evaluates and improves the test modules implementing BIST techniques created by César Limones 2016 thesis. It is important to mention that this work reports the first effort to make the full SerDes analog and digital module integration at ITESO. It required all the designers to work together in order to complete the SerDes chip design flow. In particular, the comparison data module design structure was redefined after the data flow was analyzed. The test modules simulation demonstrated the correct functionality while the timing reports with a 156.25MHz clock frequency, showed that the design is timing compliant. The SerDes final layout, which also integrated the test modules, was created with the analog modules placement and routing. However, there were issues with the routing over the analog modules, which produced an overlap on the internal metal layers. For this reason, it is encouraged to further research about the association and outcomes between the layout of the analog modules, the LEF file generation, and the analog module routing in the design flowRealizar pruebas en un chip luego de ser fabricado asegura la funcionalidad del circuito integrado. Las técnicas que contemplan la creación y aplicación de pruebas dentro del flujo de diseño del chip se llaman design for testability (diseño testable). Esta tesina evalúa y mejora los módulos de prueba que implementan técnicas de BIST, los cuales fueron creados por César Limones en la tesina del 2016. Es importante mencionar que este trabajo reporta los primeros esfuerzos realizados en el ITESO en integrar los módulos análogos y digitales que componen el SerDes. Se requirió del trabajo conjunto de todos los diseñadores para completar el flujo de diseño del chip del SerDes. En particular, la estructura del módulo de comparación fue totalmente modificada luego de que el flujo de datos fue analizado. Mediante la simulación de los módulos pruebas se demostró su correcto funcionamiento y los reportes de análisis de tiempo aplicados con un reloj a una frecuencia de 156.25MHz, mostraron que el diseño cumple con las restricciones de tiempo. El layout (diseño) final del SerDes, que integra también los módulos de pruebas, fue creado con la colocación y enrutamiento de los módulos análogos. Sin embargo, se presentaron problemas con el enrutamiento creado sobre el módulo análogo lo cual provocó un solapamiento con las capas de metal internas. Por esta razón, se exhorta a investigar sobre la asociación y resultados entre el layout de los módulos análogos, la generación del archivo LEF y el enrutamiento de los módulos análogos en el flujo de diseño.ITESO, A. C.Consejo Nacional de Ciencia y Tecnologí

CROSS-LAYER DESIGN, OPTIMIZATION AND PROTOTYPING OF NoCs FOR THE NEXT GENERATION OF HOMOGENEOUS MANY-CORE SYSTEMS

This thesis provides a whole set of design methods to enable and manage the runtime heterogeneity of features-rich industry-ready Tile-Based Networkon- Chips at different abstraction layers (Architecture Design, Network Assembling, Testing of NoC, Runtime Operation). The key idea is to maintain the functionalities of the original layers, and to improve the performance of architectures by allowing, joint optimization and layer coordinations. In general purpose systems, we address the microarchitectural challenges by codesigning and co-optimizing feature-rich architectures. In application-specific NoCs, we emphasize the event notification, so that the platform is continuously under control. At the network assembly level, this thesis proposes a Hold Time Robustness technique, to tackle the hold time issue in synchronous NoCs. At the network architectural level, the choice of a suitable synchronization paradigm requires a boost of synthesis flow as well as the coexistence with the DVFS. On one hand this implies the coexistence of mesochronous synchronizers in the network with dual-clock FIFOs at network boundaries. On the other hand, dual-clock FIFOs may be placed across inter-switch links hence removing the need for mesochronous synchronizers. This thesis will study the implications of the above approaches both on the design flow and on the performance and power quality metrics of the network. Once the manycore system is composed together, the issue of testing it arises. This thesis takes on this challenge and engineers various testing infrastructures. At the upper abstraction layer, the thesis addresses the issue of managing the fully operational system and proposes a congestion management technique named HACS. Moreover, some of the ideas of this thesis will undergo an FPGA prototyping. Finally, we provide some features for emerging technology by characterizing the power consumption of Optical NoC Interfaces

High level behavioural modelling of boundary scan architecture.

This project involves the development of a software tool which enables the integration of the IEEE 1149.1/JTAG Boundary Scan Test Architecture automatically into an ASIC (Application Specific Integrated Circuit) design. The tool requires the original design (the ASIC) to be described in VHDL-IEEE 1076 Hardware Description Language. The tool consists of the two major elements: i) A parsing and insertion algorithm developed and implemented in 'C'; ii) A high level model of the Boundary Scan Test Architecture implemented in 'VHDL'. The parsing and insertion algorithm is developed to deal with identifying the design Input/Output (I/O) terminals, their types and the order they appear in the ASIC design. It then attaches suitable Boundary Scan Cells to each I/O, except power and ground and inserts the high level models of the full Boundary Scan Architecture into the ASIC without altering the design core structure

Innovative Techniques for Testing and Diagnosing SoCs

We rely upon the continued functioning of many electronic devices for our everyday welfare, usually embedding integrated circuits that are becoming even cheaper and smaller with improved features. Nowadays, microelectronics can integrate a working computer with CPU, memories, and even GPUs on a single die, namely System-On-Chip (SoC). SoCs are also employed on automotive safety-critical applications, but need to be tested thoroughly to comply with reliability standards, in particular the ISO26262 functional safety for road vehicles. The goal of this PhD. thesis is to improve SoC reliability by proposing innovative techniques for testing and diagnosing its internal modules: CPUs, memories, peripherals, and GPUs. The proposed approaches in the sequence appearing in this thesis are described as follows: 1. Embedded Memory Diagnosis: Memories are dense and complex circuits which are susceptible to design and manufacturing errors. Hence, it is important to understand the fault occurrence in the memory array. In practice, the logical and physical array representation differs due to an optimized design which adds enhancements to the device, namely scrambling. This part proposes an accurate memory diagnosis by showing the efforts of a software tool able to analyze test results, unscramble the memory array, map failing syndromes to cell locations, elaborate cumulative analysis, and elaborate a final fault model hypothesis. Several SRAM memory failing syndromes were analyzed as case studies gathered on an industrial automotive 32-bit SoC developed by STMicroelectronics. The tool displayed defects virtually, and results were confirmed by real photos taken from a microscope. 2. Functional Test Pattern Generation: The key for a successful test is the pattern applied to the device. They can be structural or functional; the former usually benefits from embedded test modules targeting manufacturing errors and is only effective before shipping the component to the client. The latter, on the other hand, can be applied during mission minimally impacting on performance but is penalized due to high generation time. However, functional test patterns may benefit for having different goals in functional mission mode. Part III of this PhD thesis proposes three different functional test pattern generation methods for CPU cores embedded in SoCs, targeting different test purposes, described as follows: a. Functional Stress Patterns: Are suitable for optimizing functional stress during I Operational-life Tests and Burn-in Screening for an optimal device reliability characterization b. Functional Power Hungry Patterns: Are suitable for determining functional peak power for strictly limiting the power of structural patterns during manufacturing tests, thus reducing premature device over-kill while delivering high test coverage c. Software-Based Self-Test Patterns: Combines the potentiality of structural patterns with functional ones, allowing its execution periodically during mission. In addition, an external hardware communicating with a devised SBST was proposed. It helps increasing in 3% the fault coverage by testing critical Hardly Functionally Testable Faults not covered by conventional SBST patterns. An automatic functional test pattern generation exploiting an evolutionary algorithm maximizing metrics related to stress, power, and fault coverage was employed in the above-mentioned approaches to quickly generate the desired patterns. The approaches were evaluated on two industrial cases developed by STMicroelectronics; 8051-based and a 32-bit Power Architecture SoCs. Results show that generation time was reduced upto 75% in comparison to older methodologies while increasing significantly the desired metrics. 3. Fault Injection in GPGPU: Fault injection mechanisms in semiconductor devices are suitable for generating structural patterns, testing and activating mitigation techniques, and validating robust hardware and software applications. GPGPUs are known for fast parallel computation used in high performance computing and advanced driver assistance where reliability is the key point. Moreover, GPGPU manufacturers do not provide design description code due to content secrecy. Therefore, commercial fault injectors using the GPGPU model is unfeasible, making radiation tests the only resource available, but are costly. In the last part of this thesis, we propose a software implemented fault injector able to inject bit-flip in memory elements of a real GPGPU. It exploits a software debugger tool and combines the C-CUDA grammar to wisely determine fault spots and apply bit-flip operations in program variables. The goal is to validate robust parallel algorithms by studying fault propagation or activating redundancy mechanisms they possibly embed. The effectiveness of the tool was evaluated on two robust applications: redundant parallel matrix multiplication and floating point Fast Fourier Transform

Towards an embedded board-level tester: study of a configurable test processor

The demand for electronic systems with more features, higher performance, and less power consumption increases continuously. This is a real challenge for design and test engineers because they have to deal with electronic systems with ever-increasing complexity maintaining production and test costs low and meeting critical time to market deadlines. For a test engineer working at the board-level, this means that manufacturing defects must be detected as soon as possible and at a low cost. However, the use of classical test techniques for testing modern printed circuit boards is not sufficient, and in the worst case these techniques cannot be used at all. This is mainly due to modern packaging technologies, a high device density, and high operation frequencies of modern printed circuit boards. This leads to very long test times, low fault coverage, and high test costs. This dissertation addresses these issues and proposes an FPGA-based test approach for printed circuit boards. The concept is based on a configurable test processor that is temporarily implemented in the on-board FPGA and provides the corresponding mechanisms to communicate to external test equipment and co-processors implemented in the FPGA. This embedded test approach provides the flexibility to implement test functions either in the external test equipment or in the FPGA. In this manner, tests are executed at-speed increasing the fault coverage, test times are reduced, and the test system can be adapted automatically to the properties of the FPGA and devices located on the board. An essential part of the FPGA-based test approach deals with the development of a test processor. In this dissertation the required properties of the processor are discussed, and it is shown that the adaptation to the specific test scenario plays a very important role for the optimization. For this purpose, the test processor is equipped with configuration parameters at the instruction set architecture and microarchitecture level. Additionally, an automatic generation process for the test system and for the computation of some of the processor’s configuration parameters is proposed. The automatic generation process uses as input a model known as the device under test model (DUT-M). In order to evaluate the entire FPGA-based test approach and the viability of a processor for testing printed circuit boards, the developed test system is used to test interconnections to two different devices: a static random memory (SRAM) and a liquid crystal display (LCD). Experiments were conducted in order to determine the resource utilization of the processor and FPGA-based test system and to measure test time when different test functions are implemented in the external test equipment or the FPGA. It has been shown that the introduced approach is suitable to test printed circuit boards and that the test processor represents a realistic alternative for testing at board-level.Der Bedarf an elektronischen Systemen mit zusätzlichen Merkmalen, höherer Leistung und geringerem Energieverbrauch nimmt ständig zu. Dies stellt eine erhebliche Herausforderung für Entwicklungs- und Testingenieure dar, weil sie sich mit elektronischen Systemen mit einer steigenden Komplexität zu befassen haben. Außerdem müssen die Herstellungs- und Testkosten gering bleiben und die Produkteinführungsfristen so kurz wie möglich gehalten werden. Daraus folgt, dass ein Testingenieur, der auf Leiterplatten-Ebene arbeitet, die Herstellungsfehler so früh wie möglich entdecken und dabei möglichst niedrige Kosten verursachen soll. Allerdings sind die klassischen Testmethoden nicht in der Lage, die Anforderungen von modernen Leiterplatten zu erfüllen und im schlimmsten Fall können diese Testmethoden überhaupt nicht verwendet werden. Dies liegt vor allem an modernen Gehäuse-Technologien, der hohen Bauteildichte und den hohen Arbeitsfrequenzen von modernen Leiterplatten. Das führt zu sehr langen Testzeiten, geringer Testabdeckung und hohen Testkosten. Die Dissertation greift diese Problematik auf und liefert einen FPGA-basierten Testansatz für Leiterplatten. Das Konzept beruht auf einem konfigurierbaren Testprozessor, welcher im On-Board-FPGA temporär implementiert wird und die entsprechenden Mechanismen für die Kommunikation mit der externen Testeinrichtung und Co-Prozessoren im FPGA bereitstellt. Dadurch ist es möglich Testfunktionen flexibel entweder auf der externen Testeinrichtung oder auf dem FPGA zu implementieren. Auf diese Weise werden Tests at-speed ausgeführt, um die Testabdeckung zu erhöhen. Außerdem wird die Testzeit verkürzt und das Testsystem automatisch an die Eigenschaften des FPGAs und anderer Bauteile auf der Leiterplatte angepasst. Ein wesentlicher Teil des FPGA-basierten Testansatzes umfasst die Entwicklung eines Testprozessors. In dieser Dissertation wird über die benötigten Eigenschaften des Prozessors diskutiert und es wird gezeigt, dass die Anpassung des Prozessors an den spezifischen Testfall von großer Bedeutung für die Optimierung ist. Zu diesem Zweck wird der Prozessor mit Konfigurationsparametern auf der Befehlssatzarchitektur-Ebene und Mikroarchitektur-Ebene ausgerüstet. Außerdem wird ein automatischer Generierungsprozess für die Realisierung des Testsystems und für die Berechnung einer Untergruppe von Konfigurationsparametern des Prozessors vorgestellt. Der automatische Generierungsprozess benutzt als Eingangsinformation ein Modell des Prüflings (device under test model, DUT-M). Das entwickelte Testsystem wurde zum Testen von Leiterplatten für Verbindungen zwischen dem FPGA und zwei Bauteilen verwendet, um den FPGA-basierten Testansatz und die Durchführbarkeit des Testprozessors für das Testen auf Leiterplatte-Ebene zu evaluieren. Die zwei Bauteile sind ein Speicher mit direktem Zugriff (static random-access memory, SRAM) und eine Flüssigkristallanzeige (liquid crystal display, LCD). Die Experimente wurden durchgeführt, um den Ressourcenverbrauch des Prozessors und Testsystems festzustellen und um die Testzeit zu messen. Dies geschah durch die Implementierung von unterschiedlichen Testfunktionen auf der externen Testeinrichtung und dem FPGA. Dadurch konnte gezeigt werden, dass der FPGA-basierte Ansatz für das Testen von Leiterplatten geeignet ist und dass der Testprozessor eine realistische Alternative für das Testen auf Leiterplatten-Ebene ist

Tester for chosen sub-standard of the IEEE 802.1Q

Tato práce se zabývá analyzováním IEEE 802.1Q standardu TSN skupiny a návrhem testovacího modulu. Testovací modul je napsán v jazyku VHDL a je možné jej implementovat do Intel Stratix® V GX FPGA (5SGXEA7N2F45C2) vývojové desky. Standard IEEE 802.1Q (TSN) definuje deterministickou komunikace přes Ethernet sít, v reálném čase, požíváním globálního času a správným rozvrhem vysíláním a příjmem zpráv. Hlavní funkce tohoto standardu jsou: časová synchronizace, plánování provozu a konfigurace sítě. Každá z těchto funkcí je definovaná pomocí více různých podskupin tohoto standardu. Podle definice IEEE 802.1Q standardu je možno tyto podskupiny vzájemně libovolně kombinovat. Některé podskupiny standardu nemohou fungovat nezávisle, musí využívat funkce jiných podskupin standardu. Realizace funkce podskupin standardu je možná softwarově, hardwarově, nebo jejich kombinací. Na základě výše uvedených fakt, implementace podskupin standardu, které jsou softwarově související, byly vyloučené. Taky byly vyloučené podskupiny standardů, které jsou závislé na jiných podskupinách. IEEE 802.1Qbu byl vybrán jako vhodná část pro realizaci hardwarového testu. Různé způsoby testování byly vysvětleny jako DFT, BIST, ATPG a další jiné techniky. Pro hardwarové testování byla vybrána „Protocol Aware (PA)“technika, protože tato technika zrychluje testování, dovoluje opakovanou použitelnost a taky zkracuje dobu uvedení na trh. Testovací modul se skládá ze dvou objektů (generátor a monitor), které mají implementovanou IEEE 802.1Qbu podskupinu standardu. Funkce generátoru je vygenerovat náhodné nebo nenáhodné impulzy a potom je poslat do testovaného zařízeni ve správném definovaném protokolu. Funkce monitoru je přijat ethernet rámce a ověřit jejich správnost. Objekty jsou navrhnuty stejným způsobem na „TOP“úrovni a skládají se ze čtyř modulů: Avalon MM rozhraní, dvou šablon a jednoho portu. Avalon MM rozhraní bylo vytvořeno pro komunikaci softwaru s hardwarem. Tento modul přijme pakety ze softwaru a potom je dekóduje podle definovaného protokolu a „pod-protokolu “. „Pod-protokol“se skládá z příkazu a hodnoty daného příkazu. Podle dekódovaného příkazu a hodnot daných příkazem je kontrolovaný celý objekt. Šablona se používá na generování nebo ověřování náhodných nebo nenáhodných dat. Dvě šablony byly implementovány pro expresní ověřování nebo preempční transakce, definované IEEE 802.1Qbu. Porty byly vytvořené pro komunikaci mezi testovaným zařízením a šablonou podle daného standardu. Port „generátor“má za úkol vybrat a vyslat rámce podle priority a času vysílaní. Port „monitor“přijme rámce do „content-addressable memory”, která ověřuje priority rámce a podle toho je posílá do správné šablony. Výsledky prokázaly, že tato testovací technika dosahuje vysoké rychlosti a rychlé implementace.This master paper is dealing with the analysis of IEEE 802.1Q group of TSN standards and with the design of HW tester. Standard IEEE 802.1Qbu has appeared to be an optimal solution for this paper. Detail explanation of this sub-standard are included in this paper. As HW test the implementation, a protocol aware technique was chosen in order to accelerate testing. Paper further describes architecture of this tester, with detail explanation of the modules. Essential issue of protocol aware controlling objects by SW, have been resolved and described. Result proof that this technique has reached higher speed of testing, reusability, and fast implementation.

Studies on Core-Based Testing of System-on-Chips Using Functional Bus and Network-on-Chip Interconnects

The tests of a complex system such as a microprocessor-based system-onchip (SoC) or a network-on-chip (NoC) are difficult and expensive. In this thesis, we propose three core-based test methods that reuse the existing functional interconnects-a flat bus, hierarchical buses of multiprocessor SoC's (MPSoC), and a N oC-in order to avoid the silicon area cost of a dedicated test access mechanism (TAM). However, the use of functional interconnects as functional TAM's introduces several new problems. During tests, the interconnects-including the bus arbitrator, the bus bridges, and the NoC routers-operate in the functional mode to transport the test stimuli and responses, while the core under tests (CUT) operate in the test mode. Second, the test data is transported to the CUT through the functional bus, and not directly to the test port. Therefore, special core test wrappers that can provide the necessary control signals required by the different functional interconnect are proposed. We developed two types of wrappers, one buffer-based wrapper for the bus-based systems and another pair of complementary wrappers for the NoCbased systems. Using the core test wrappers, we propose test scheduling schemes for the three functionally different types of interconnects. The test scheduling scheme for a flat bus is developed based on an efficient packet scheduling scheme that minimizes both the buffer sizes and the test time under a power constraint. The schedulingscheme is then extended to take advantage of the hierarchical bus architecture of the MPSoC systems. The third test scheduling scheme based on the bandwidth sharing is developed specifically for the NoC-based systems. The test scheduling is performed under the objective of co-optimizing the wrapper area cost and the resulting test application time using the two complementary NoC wrappers. For each of the proposed methodology for the three types of SoC architec .. ture, we conducted a thorough experimental evaluation in order to verify their effectiveness compared to other methods

Testability and redundancy techniques for improved yield and reliability of CMOS VLSI circuits

The research presented in this thesis is concerned with the design of fault-tolerant integrated circuits as a contribution to the design of fault-tolerant systems. The economical manufacture of very large area ICs will necessitate the incorporation of fault-tolerance features which are routinely employed in current high density dynamic random access memories. Furthermore, the growing use of ICs in safety-critical applications and/or hostile environments in addition to the prospect of single-chip systems will mandate the use of fault-tolerance for improved reliability. A fault-tolerant IC must be able to detect and correct all possible faults that may affect its operation. The ability of a chip to detect its own faults is not only necessary for fault-tolerance, but it is also regarded as the ultimate solution to the problem of testing. Off-line periodic testing is selected for this research because it achieves better coverage of physical faults and it requires less extra hardware than on-line error detection techniques. Tests for CMOS stuck-open faults are shown to detect all other faults. Simple test sequence generation procedures for the detection of all faults are derived. The test sequences generated by these procedures produce a trivial output, thereby, greatly simplifying the task of test response analysis. A further advantage of the proposed test generation procedures is that they do not require the enumeration of faults. The implementation of built-in self-test is considered and it is shown that the hardware overhead is comparable to that associated with pseudo-random and pseudo-exhaustive techniques while achieving a much higher fault coverage through-the use of the proposed test generation procedures. The consideration of the problem of testing the test circuitry led to the conclusion that complete test coverage may be achieved if separate chips cooperate in testing each other's untested parts. An alternative approach towards complete test coverage would be to design the test circuitry so that it is as distributed as possible and so that it is tested as it performs its function. Fault correction relies on the provision of spare units and a means of reconfiguring the circuit so that the faulty units are discarded. This raises the question of what is the optimum size of a unit? A mathematical model, linking yield and reliability is therefore developed to answer such a question and also to study the effects of such parameters as the amount of redundancy, the size of the additional circuitry required for testing and reconfiguration, and the effect of periodic testing on reliability. The stringent requirement on the size of the reconfiguration logic is illustrated by the application of the model to a typical example. Another important result concerns the effect of periodic testing on reliability. It is shown that periodic off-line testing can achieve approximately the same level of reliability as on-line testing, even when the time between tests is many hundreds of hours

Fault-Tolerant Computing: An Overview

Coordinated Science Laboratory was formerly known as Control Systems LaboratoryNASA / NAG-1-613Semiconductor Research Corporation / 90-DP-109Joint Services Electronics Program / N00014-90-J-127