300 research outputs found

    Beam scanning by liquid-crystal biasing in a modified SIW structure

    Get PDF
    A fixed-frequency beam-scanning 1D antenna based on Liquid Crystals (LCs) is designed for application in 2D scanning with lateral alignment. The 2D array environment imposes full decoupling of adjacent 1D antennas, which often conflicts with the LC requirement of DC biasing: the proposed design accommodates both. The LC medium is placed inside a Substrate Integrated Waveguide (SIW) modified to work as a Groove Gap Waveguide, with radiating slots etched on the upper broad wall, that radiates as a Leaky-Wave Antenna (LWA). This allows effective application of the DC bias voltage needed for tuning the LCs. At the same time, the RF field remains laterally confined, enabling the possibility to lay several antennas in parallel and achieve 2D beam scanning. The design is validated by simulation employing the actual properties of a commercial LC medium

    Plastic Optical Fibers as Passive Optical Front-Ends for Visible Light Communication

    Get PDF

    1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

    Get PDF
    A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance

    Plastic Optical Fibers as Passive Optical Front-Ends for Visible Light Communication

    Get PDF

    Decentralized Ultra-Reliable Low-Latency Communications through Concurrent Cooperative Transmission

    Get PDF
    Emerging cyber-physical systems demand for communication technologies that enable seamless interactions between humans and physical objects in a shared environment. This thesis proposes decentralized URLLC (dURLLC) as a new communication paradigm that allows the nodes in a wireless multi-hop network (WMN) to disseminate data quickly, reliably and without using a centralized infrastructure. To enable the dURLLC paradigm, this thesis explores the practical feasibility of concurrent cooperative transmission (CCT) with orthogonal frequency-division multiplexing (OFDM). CCT allows for an efficient utilization of the medium by leveraging interference instead of trying to avoid collisions. CCT-based network flooding disseminates data in a WMN through a reception-triggered low-level medium access control (MAC). OFDM provides high data rates by using a large bandwidth, resulting in a short transmission duration for a given amount of data. This thesis explores CCT-based network flooding with the OFDM-based IEEE 802.11 Non-HT and HT physical layers (PHYs) to enable interactions with commercial devices. An analysis of CCT with the IEEE 802.11 Non-HT PHY investigates the combined effects of the phase offset (PO), the carrier frequency offset (CFO) and the time offset (TO) between concurrent transmitters, as well as the elapsed time. The analytical results of the decodability of a CCT are validated in simulations and in testbed experiments with Wireless Open Access Research Platform (WARP) v3 software-defined radios (SDRs). CCT with coherent interference (CI) is the primary approach of this thesis. Two prototypes for CCT with CI are presented that feature mechanisms for precise synchronization in time and frequency. One prototype is based on the WARP v3 and its IEEE 802.11 reference design, whereas the other prototype is created through firmware modifications of the Asus RT-AC86U wireless router. Both prototypes are employed in testbed experiments in which two groups of nodes generate successive CCTs in a ping-pong fashion to emulate flooding processes with a very large number of hops. The nodes stay synchronized in experiments with 10 000 successive CCTs for various modulation and coding scheme (MCS) indices and MAC service data unit (MSDU) sizes. The URLLC requirement of delivering a 32-byte MSDU with a reliability of 99.999 % and with a latency of 1 ms is assessed in experiments with 1 000 000 CCTs, while the reliability is approximated by means of the frame reception rate (FRR). An FRR of at least 99.999 % is achieved at PHY data rates of up to 48 Mbit/s under line-of-sight (LOS) conditions and at PHY data rates of up to 12 Mbit/s under non-line-of-sight (NLOS) conditions on a 20 MHz wide channel, while the latency per hop is 48.2 µs and 80.2 µs, respectively. With four multiple input multiple output (MIMO) spatial streams on a 40 MHz wide channel, a LOS receiver achieves an FRR of 99.5 % at a PHY data rate of 324 Mbit/s. For CCT with incoherent interference, this thesis proposes equalization with time-variant zero-forcing (TVZF) and presents a TVZF receiver for the IEEE 802.11 Non-HT PHY, achieving an FRR of up to 92 % for CCTs from three unsyntonized commercial devices. As CCT-based network flooding allows for an implicit time synchronization of all nodes, a reception-triggered low-level MAC and a reservation-based high-level MAC may in combination support various applications and scenarios under the dURLLC paradigm

    Modelling, Analysis and Design of Optimised Electronic Circuits for Visible Light Communication Systems

    Get PDF
    This thesis explores new circuit design techniques and topologies to extend the bandwidth of visible light communication (VLC) transmitters and receivers, by ameliorating the bandwidth-limiting effects of commonly used optoelectronic devices. The thesis contains detailed literature review of transmitter and receiver designs, which inspired two directions of work. The first proposes new designs of optically lossless light emitting diode (LED) bandwidth extension technique that utilises a negative capacitance circuit to offset the diode’s bandwidth-limiting capacitance. The negative capacitance circuit was studied and verified through newly developed mathematical analysis, modelling and experimental demonstration. The bandwidth advantage of the proposed technique was demonstrated through measurements in conjunction with several colour LEDs, demonstrating up to 500% bandwidth extension with no loss of optical power. The second direction of work enhances the bandwidth of VLC receivers through new designs of ultra-low input impedance transimpedance amplifiers (TIAs), designed to be insensitive to the high photodiode capacitances (Cpd) of large area detectors. Moreover, the thesis proposes a new circuit, which modifies the traditional regulated cascode (RGC) circuit to enhance its bandwidth and gain. The modified RGC amplifier efficiently treats significant RGC inherent bandwidth limitations and is shown, through mathematical analysis, modelling and experimental measurements to extend the bandwidth further by up to 200%. The bandwidth advantage of such receivers was demonstrated in measurements, using several large area photodiodes of area up to 600 mm^2, resulting in a substantial bandwidth improvement of up to 1000%, relative to a standard 50 Ω termination. An inherent limitation of large area photodiodes, associated with internal resistive elements, was identified and ameliorated, through the design of negative resistance circuits. Altogether, this research resulted in a set of design methods and practical circuits, which will hopefully contribute to wider adoption of VLC systems and may be applied in areas beyond VLC

    Interference mitigation in LiFi networks

    Get PDF
    Due to the increasing demand for wireless data, the radio frequency (RF) spectrum has become a very limited resource. Alternative approaches are under investigation to support the future growth in data traffic and next-generation high-speed wireless communication systems. Techniques such as massive multiple-input multiple-output (MIMO), millimeter wave (mmWave) communications and light-fidelity (LiFi) are being explored. Among these technologies, LiFi is a novel bi-directional, high-speed and fully networked wireless communication technology. However, inter-cell interference (ICI) can significantly restrict the system performance of LiFi attocell networks. This thesis focuses on interference mitigation in LiFi attocell networks. The angle diversity receiver (ADR) is one solution to address the issue of ICI as well as frequency reuse in LiFi attocell networks. With the property of high concentration gain and narrow field of view (FOV), the ADR is very beneficial for interference mitigation. However, the optimum structure of the ADR has not been investigated. This motivates us to propose the optimum structures for the ADRs in order to fully exploit the performance gain. The impact of random device orientation and diffuse link signal propagation are taken into consideration. The performance comparison between the select best combining (SBC) and maximum ratio combining (MRC) is carried out under different noise levels. In addition, the double source (DS) system, where each LiFi access point (AP) consists of two sources transmitting the same information signals but with opposite polarity, is proven to outperform the single source (SS) system under certain conditions. Then, to overcome issues around ICI, random device orientation and link blockage, hybrid LiFi/WiFi networks (HLWNs) are considered. In this thesis, dynamic load balancing (LB) considering handover in HLWNs is studied. The orientation-based random waypoint (ORWP) mobility model is considered to provide a more realistic framework to evaluate the performance of HLWNs. Based on the low-pass filtering effect of the LiFi channel, we firstly propose an orthogonal frequency division multiple access (OFDMA)-based resource allocation (RA) method in LiFi systems. Also, an enhanced evolutionary game theory (EGT)-based LB scheme with handover in HLWNs is proposed. Finally, due to the characteristic of high directivity and narrow beams, a vertical-cavity surface-emitting laser (VCSEL) array transmission system has been proposed to mitigate ICI. In order to support mobile users, two beam activation methods are proposed. The beam activation based on the corner-cube retroreflector (CCR) can achieve low power consumption and almost-zero delay, allowing real-time beam activation for high-speed users. The mechanism based on the omnidirectional transmitter (ODTx) is suitable for low-speed users and very robust to random orientation

    Design und Evaluation von Hardware-Architekturen zur Powerline-basierten Kommunikation unter extremen Umweltbedingungen

    Get PDF
    Moderne elektronische Geräte setzten vermehrt auf den Austausch von Informationen mit dem Benutzer oder einem Online-Dienst des Herstellers, wie zum Beispiel im Smart Home, der Staubsauger-Roboter oder die Waschmaschine. Die Verbindung erfolgt zumeist über drahtlose Kommunikation zum Beispiel auf dem 2,4 GHz-Funkkanal, welcher gerade in dicht besiedelten Städten teilweise schon überlastet ist. Eine Alternative bietet die drahtgebundene Kommunikation über die Stromversorgungsleitung, auch Powerline-Kommunikation genannt. Hierbei werden die Informationen auf freie Frequenzbänder oberhalb der Netzfrequenz moduliert und konkurrieren dabei nur mit den anderen Teilnehmern des eigenen Stromnetzes. Ein Problem bei dieser Art der Kommunikation ist der Übetragungskanal, der nicht für eine hochfrequente Übertragung ausgelegt ist und starke Störungen durch Lastwechsel oder Reflexionen an Impedanzsprüngen erzeugt. Um diese Störungen zu kompensieren verwenden moderne Powerline-Kommunikationsstandards robuste Kanalkodierverfahren, um Fehler in den übertragenen Informationen empfangsseitig korrigieren zu können. Auf Grund dieser robusten Fehlerkorrketurverfahren, eignen sich diese Standards auch für die Kommunikation unter extremen Umweltbedingungen in der Tiefenbohrtechnik. Dabei befinden sich die elektronischen Komponenten entlang der letzten 100 m des Bohrstrangs mehrere Kilometer tief unter der Erde, wo Umgebungstemperaturen mehr als 150 °C, Drücke bis 207 MPa und mechanische Schocks auftreten. Diese extremen Umweltbedingungen haben sowohl Einfluss auf die elektronischen Komponenten, als auch auf den Übetragungskanal der Powerline-Kommunikation selbst. In dieser Arbeit wird erstmalig eine Entwurfsraumexploration für hochtempteraturfeste Hardware-Plattformen eines Breitband-Powerline-Kommunikationssystems durchgeführt. Dabei wird ein Abtausch zwischen Durchsatz, Flexibiltät und Hardware-Ressourcen aufgezeigt, der verschiedene Pareto-optimale Punkte enthält. Diese Pareto-optimalen Punkte umfassen sowohl Prozessor-basiere Plattformen, als auch eine dedizierte Implementierung. Die dedizierte Implementierung wird anschließend in einer FPGA-basierten Emulationen bezüglich Durchsatz, Latenz und Skalierbarkeit des Netzwerkes evaluiert und optimale Konfigurationen aufgezeigt. Abschließend wird diese optimale Konfiguration für die Fertigung als Chip in einer Hochtemperaturtechnologie vorbereitet. Der gefertigte Chip wird auf einer hochtemperaturfesten Leiterplatte in einer Klimakammer unter extremen Umweltbedingungen verifiziert und evaluiert. Die Ergebnisse zeigen eine geringe Leistungsaufnahme und eine stabile Kommunikation mit geringen Paketverlustraten bis zu einer Sperrschichttemperatur von 220 °C. Die Messungen zeigen einen linearen Abtausch zwischen Spannungsversorgung und Stabilität der Kommunikation von 7 mW/°C. Damit erweitert diese Arbeit den aktuellen Stand der Forschung um den ersten Breitband-Powerline-Kommunikation-Chip, der unter extremen Umweltbedingungen evaluiert und charakterisiert wurde

    Advanced Applications of Rapid Prototyping Technology in Modern Engineering

    Get PDF
    Rapid prototyping (RP) technology has been widely known and appreciated due to its flexible and customized manufacturing capabilities. The widely studied RP techniques include stereolithography apparatus (SLA), selective laser sintering (SLS), three-dimensional printing (3DP), fused deposition modeling (FDM), 3D plotting, solid ground curing (SGC), multiphase jet solidification (MJS), laminated object manufacturing (LOM). Different techniques are associated with different materials and/or processing principles and thus are devoted to specific applications. RP technology has no longer been only for prototype building rather has been extended for real industrial manufacturing solutions. Today, the RP technology has contributed to almost all engineering areas that include mechanical, materials, industrial, aerospace, electrical and most recently biomedical engineering. This book aims to present the advanced development of RP technologies in various engineering areas as the solutions to the real world engineering problems

    Mobile and Wireless Communications

    Get PDF
    Mobile and Wireless Communications have been one of the major revolutions of the late twentieth century. We are witnessing a very fast growth in these technologies where mobile and wireless communications have become so ubiquitous in our society and indispensable for our daily lives. The relentless demand for higher data rates with better quality of services to comply with state-of-the art applications has revolutionized the wireless communication field and led to the emergence of new technologies such as Bluetooth, WiFi, Wimax, Ultra wideband, OFDMA. Moreover, the market tendency confirms that this revolution is not ready to stop in the foreseen future. Mobile and wireless communications applications cover diverse areas including entertainment, industrialist, biomedical, medicine, safety and security, and others, which definitely are improving our daily life. Wireless communication network is a multidisciplinary field addressing different aspects raging from theoretical analysis, system architecture design, and hardware and software implementations. While different new applications are requiring higher data rates and better quality of service and prolonging the mobile battery life, new development and advanced research studies and systems and circuits designs are necessary to keep pace with the market requirements. This book covers the most advanced research and development topics in mobile and wireless communication networks. It is divided into two parts with a total of thirty-four stand-alone chapters covering various areas of wireless communications of special topics including: physical layer and network layer, access methods and scheduling, techniques and technologies, antenna and amplifier design, integrated circuit design, applications and systems. These chapters present advanced novel and cutting-edge results and development related to wireless communication offering the readers the opportunity to enrich their knowledge in specific topics as well as to explore the whole field of rapidly emerging mobile and wireless networks. We hope that this book will be useful for students, researchers and practitioners in their research studies
    corecore