11,970 research outputs found
Adaptive multibeam phased array design for a Spacelab experiment
The parametric tradeoff analyses and design for an Adaptive Multibeam Phased Array (AMPA) for a Spacelab experiment are described. This AMPA Experiment System was designed with particular emphasis to maximize channel capacity and minimize implementation and cost impacts for future austere maritime and aeronautical users, operating with a low gain hemispherical coverage antenna element, low effective radiated power, and low antenna gain-to-system noise temperature ratio
Efficient DSP and Circuit Architectures for Massive MIMO: State-of-the-Art and Future Directions
Massive MIMO is a compelling wireless access concept that relies on the use
of an excess number of base-station antennas, relative to the number of active
terminals. This technology is a main component of 5G New Radio (NR) and
addresses all important requirements of future wireless standards: a great
capacity increase, the support of many simultaneous users, and improvement in
energy efficiency. Massive MIMO requires the simultaneous processing of signals
from many antenna chains, and computational operations on large matrices. The
complexity of the digital processing has been viewed as a fundamental obstacle
to the feasibility of Massive MIMO in the past. Recent advances on
system-algorithm-hardware co-design have led to extremely energy-efficient
implementations. These exploit opportunities in deeply-scaled silicon
technologies and perform partly distributed processing to cope with the
bottlenecks encountered in the interconnection of many signals. For example,
prototype ASIC implementations have demonstrated zero-forcing precoding in real
time at a 55 mW power consumption (20 MHz bandwidth, 128 antennas, multiplexing
of 8 terminals). Coarse and even error-prone digital processing in the antenna
paths permits a reduction of consumption with a factor of 2 to 5. This article
summarizes the fundamental technical contributions to efficient digital signal
processing for Massive MIMO. The opportunities and constraints on operating on
low-complexity RF and analog hardware chains are clarified. It illustrates how
terminals can benefit from improved energy efficiency. The status of technology
and real-life prototypes discussed. Open challenges and directions for future
research are suggested.Comment: submitted to IEEE transactions on signal processin
Reconfigurable Intelligent Surfaces for Energy Efficiency in Wireless Communication
The adoption of a Reconfigurable Intelligent Surface (RIS) for downlink
multi-user communication from a multi-antenna base station is investigated in
this paper. We develop energy-efficient designs for both the transmit power
allocation and the phase shifts of the surface reflecting elements, subject to
individual link budget guarantees for the mobile users. This leads to
non-convex design optimization problems for which to tackle we propose two
computationally affordable approaches, capitalizing on alternating
maximization, gradient descent search, and sequential fractional programming.
Specifically, one algorithm employs gradient descent for obtaining the RIS
phase coefficients, and fractional programming for optimal transmit power
allocation. Instead, the second algorithm employs sequential fractional
programming for the optimization of the RIS phase shifts. In addition, a
realistic power consumption model for RIS-based systems is presented, and the
performance of the proposed methods is analyzed in a realistic outdoor
environment. In particular, our results show that the proposed RIS-based
resource allocation methods are able to provide up to higher energy
efficiency, in comparison with the use of regular multi-antenna
amplify-and-forward relaying.Comment: Accepted by IEEE TWC; additional materials on the topic are included
in the 2018 conference publications at ICASSP
(https://ieeexplore.ieee.org/abstract/document/8461496) and GLOBECOM 2018
(arXiv:1809.05397
User Antennas
The following subject areas are covered: (1) impact of frequency change of user and spacecraft antenna gain and size; (2) basic personal terminal antennas (impact of 20/30 GHz frequency separation; parametric studies - gain, size, weight; gain and figure of merit (G/T); design data for selected antenna concepts; critical technologies and development goals; and recommendations); and (3) user antenna radiation safety concerns
An effective AMS Top-Down Methodology Applied to the Design of a Mixed-SignalUWB System-on-Chip
The design of Ultra Wideband (UWB) mixed-signal SoC for localization applications in wireless personal area networks is currently investigated by several researchers. The complexity of the design claims for effective top-down methodologies. We propose a layered approach based on VHDL-AMS for the first design stages and on an intelligent use of a circuit-level simulator for the transistor-level phase. We apply the latter just to one block at a time and wrap it within the system-level VHDL-AMS description. This method allows to capture the impact of circuit-level design choices and non-idealities on system performance. To demonstrate the effectiveness of the methodology we show how the refinement of the design affects specific UWB system parameters such as bit-error rate and localization estimations
Massive MIMO with Non-Ideal Arbitrary Arrays: Hardware Scaling Laws and Circuit-Aware Design
Massive multiple-input multiple-output (MIMO) systems are cellular networks
where the base stations (BSs) are equipped with unconventionally many antennas,
deployed on co-located or distributed arrays. Huge spatial degrees-of-freedom
are achieved by coherent processing over these massive arrays, which provide
strong signal gains, resilience to imperfect channel knowledge, and low
interference. This comes at the price of more infrastructure; the hardware cost
and circuit power consumption scale linearly/affinely with the number of BS
antennas . Hence, the key to cost-efficient deployment of large arrays is
low-cost antenna branches with low circuit power, in contrast to today's
conventional expensive and power-hungry BS antenna branches. Such low-cost
transceivers are prone to hardware imperfections, but it has been conjectured
that the huge degrees-of-freedom would bring robustness to such imperfections.
We prove this claim for a generalized uplink system with multiplicative
phase-drifts, additive distortion noise, and noise amplification. Specifically,
we derive closed-form expressions for the user rates and a scaling law that
shows how fast the hardware imperfections can increase with while
maintaining high rates. The connection between this scaling law and the power
consumption of different transceiver circuits is rigorously exemplified. This
reveals that one can make the circuit power increase as , instead of
linearly, by careful circuit-aware system design.Comment: Accepted for publication in IEEE Transactions on Wireless
Communications, 16 pages, 8 figures. The results can be reproduced using the
following Matlab code: https://github.com/emilbjornson/hardware-scaling-law
Communication Subsystems for Emerging Wireless Technologies
The paper describes a multi-disciplinary design of modern communication systems. The design starts with the analysis of a system in order to define requirements on its individual components. The design exploits proper models of communication channels to adapt the systems to expected transmission conditions. Input filtering of signals both in the frequency domain and in the spatial domain is ensured by a properly designed antenna. Further signal processing (amplification and further filtering) is done by electronics circuits. Finally, signal processing techniques are applied to yield information about current properties of frequency spectrum and to distribute the transmission over free subcarrier channels
- âŠ