Enhanced WDM-OFDM-PON System Based on Higher Data Transmitted with Modulation Technique

ABSTRACT:- Studies among the field communication system existing technique and proposes and by experimentation demonstrate a multiuser wavelengthdivision-multiplexing passive optical network (WDM-PON) system combining with orthogonal frequency division multiple (OFDM) technique. A tunable multiwavelength optical comb is intended to provide flat optical lines for helping the configuration of the multiple source-free optical network units WDM-OFDM-PON system supported normal single-mode fiber (SSMF). In WDM based on fiber, optical network communications using wavelength with multiplex or demultiplex may be a technology that multiplexes a variety of optical carrier signals onto one fiber by victimization completely different wavelengths of optical device lightweight. this system allows bidirectional communications over one strand of fiber, also as multiplication of capability and calculate BER (Bit Error Rate) and OSNR (optical signal noise ratio) finally; a comparison of by experimentation achieved receiver sensitivities and transmission distances victimization these receivers is given. The very best spectral potency and longest transmission distance at the very best bit rate. WDM based applications like transmission data, medical imaging data, and digital audio data and video conferencing data are information measure-intensive with the Advance in optical technology providing verdant bandwidth, it's natural to increase the multicast construct to optical networks so as to realize increased performance. Our projected scheme (PGA) based on information load transmitted capability improve supported higher information transmitted over these channels and high data up to develop in Matlab tool and using optical Interleaved the OFDM model and analysis the performance of the WDM-PON system

Optimization of multicore optical fibers with fiber Bragg gratings towards bend and shape sensing

A shape sensor based on fiber Bragg gratings (FBGs) in multicore fibers is a complex device with multiple factors which have to be accounted for a successful measure- ment system. In this dissertation, I considered several aspects of such shape and curvature sensors

Spatially integrated erbium-doped fiber amplifiers enabling space-division multiplexing

L'augmentation exponentielle de la demande de bande passante pour les communications laisse présager une saturation prochaine de la capacité des réseaux de télécommunications qui devrait se matérialiser au cours de la prochaine décennie. En effet, la théorie de l’information prédit que les effets non linéaires dans les fibres monomodes limite la capacité de transmission de celles-ci et peu de gain à ce niveau peut être espéré des techniques traditionnelles de multiplexage développées et utilisées jusqu’à présent dans les systèmes à haut débit. La dimension spatiale du canal optique est proposée comme un nouveau degré de liberté qui peut être utilisé pour augmenter le nombre de canaux de transmission et, par conséquent, résoudre cette menace de «crise de capacité». Ainsi, inspirée par les techniques micro-ondes, la technique émergente appelée multiplexage spatial (SDM) est une technologie prometteuse pour la création de réseaux optiques de prochaine génération. Pour réaliser le SDM dans les liens de fibres optiques, il faut réexaminer tous les dispositifs intégrés, les équipements et les sous-systèmes. Parmi ces éléments, l'amplificateur optique SDM est critique, en particulier pour les systèmes de transmission pour les longues distances. En raison des excellentes caractéristiques de l'amplificateur à fibre dopée à l'erbium (EDFA) utilisé dans les systèmes actuels de pointe, l'EDFA est à nouveau un candidat de choix pour la mise en œuvre des amplificateurs SDM pratiques. Toutefois, étant donné que le SDM introduit une variation spatiale du champ dans le plan transversal de la fibre, les amplificateurs à fibre dopée à l'erbium spatialement intégrés (SIEDFA) nécessitent une conception soignée. Dans cette thèse, nous examinons tout d'abord les progrès récents du SDM, en particulier les amplificateurs optiques SDM. Ensuite, nous identifions et discutons les principaux enjeux des SIEDFA qui exigent un examen scientifique. Suite à cela, la théorie des EDFA est brièvement présentée et une modélisation numérique pouvant être utilisée pour simuler les SIEDFA est proposée. Sur la base d'un outil de simulation fait maison, nous proposons une nouvelle conception des profils de dopage annulaire des fibres à quelques-modes dopées à l'erbium (ED-FMF) et nous évaluons numériquement la performance d’un amplificateur à un étage, avec fibre à dopage annulaire, à ainsi qu’un amplificateur à double étage pour les communications sur des fibres ne comportant que quelques modes. Par la suite, nous concevons des fibres dopées à l'erbium avec une gaine annulaire et multi-cœurs (ED-MCF). Nous avons évalué numériquement le recouvrement de la pompe avec les multiples cœurs de ces amplificateurs. En plus de la conception, nous fabriquons et caractérisons une fibre multi-cœurs à quelques modes dopées à l'erbium. Nous réalisons la première démonstration des amplificateurs à fibre optique spatialement intégrés incorporant de telles fibres dopées. Enfin, nous présentons les conclusions ainsi que les perspectives de cette recherche. La recherche et le développement des SIEDFA offriront d'énormes avantages non seulement pour les systèmes de transmission future SDM, mais aussi pour les systèmes de transmission monomode sur des fibres standards à un cœur car ils permettent de remplacer plusieurs amplificateurs par un amplificateur intégré.The exponential increase of communication bandwidth demand is giving rise to the so-called ‘capacity crunch’ expected to materialize within the next decade. Due to the nonlinear limit of the single mode fiber predicted by the information theory, all the state-of-the-art techniques which have so far been developed and utilized in order to extend the optical fiber communication capacity are exhausted. The spatial domain of the lightwave links is proposed as a new degree of freedom that can be employed to increase the number of transmission paths and, subsequently, overcome the looming ‘capacity crunch’. Therefore, the emerging technique named space-division multiplexing (SDM) is a promising candidate for creating next-generation optical networks. To realize SDM in optical fiber links, one needs to investigate novel spatially integrated devices, equipment, and subsystems. Among these elements, the SDM amplifier is a critical subsystem, in particular for the long-haul transmission system. Due to the excellent features of the erbium-doped fiber amplifier (EDFA) used in current state-of-the-art systems, the EDFA is again a prime candidate for implementing practical SDM amplifiers. However, since the SDM introduces a spatial variation of the field in the transverse plane of the optical fibers, spatially integrated erbium-doped fiber amplifiers (SIEDFA) require a careful design. In this thesis, we firstly review the recent progress in SDM, in particular, the SDM optical amplifiers. Next, we identify and discuss the key issues of SIEDFA that require scientific investigation. After that, the EDFA theory is briefly introduced and a corresponding numerical modeling that can be used for simulating the SIEDFA is proposed. Based on a home-made simulation tool, we propose a novel design of an annular based doping profile of few-mode erbium-doped fibers (FM-EDF) and numerically evaluate the performance of single stage as well as double-stage few-mode erbium-doped fiber amplifiers (FM-EDFA) based on such fibers. Afterward, we design annular-cladding erbium-doped multicore fibers (MC-EDF) and numerically evaluate the cladding pumped multicore erbium-doped fiber amplifier (MC-EDFA) based on these fibers as well. In addition to fiber design, we fabricate and characterize a multicore few-mode erbium-doped fiber (MC-FM-EDF), and perform the first demonstration of the spatially integrated optical fiber amplifiers incorporating such specialty doped fibers. Finally, we present the conclusions as well as the perspectives of this research. In general, the investigation and development of the SIEDFA will bring tremendous benefits not only for future SDM transmission systems but also for current state-of-the-art single-mode single-core transmission systems by replacing plural amplifiers by one integrated amplifier

Integrated multicore fibre devices for optical trapping

The work described in this thesis details the development of a multicore fibre device that can be used to optically trap multiple cells and particles. The optical trapping of multiple cells at close proximity allows for cell-to-cell interactions to be studied. Current methods available for creating arrays of traps are free space optical systems that use diffractive optics, laser scanning techniques or the interference of multiple beams to create the multiple traps. A fully integrated, fibre optic based, multiple particles, optical trapping device could be used in non-optical research facilities such as biological laboratories to aid with their research into cellular processes. In order to create the multiple traps, the distal end of the multicore fibre needs to be modified to induce a lensing effect. The multicore fibre device presented in this thesis was lensed in a fusion splicer; this refracts the outputs from the four cores to a common point in the far field where interference fringes are formed. The initial investigation demonstrated one-dimensional interferometric optical trapping through coupling light into two of the diagonal cores of the lensed multicore fibre. This produced linear interference fringes approximately 250 ± 25 μm from the end of the fibre with a fringe spacing of 2 ± 0.3 μm. The linear interference fringes were used to optically trap polystyrene microspheres with diameters of 1.3 μm, 2 μm and 3 μm in the high intensity regions of the fringes. Coupling into all four cores using a diffractive optical element produced an array of intensity peaks across the interference pattern with high visibility fringes greater than 80 %. Each intensity peak, spaced 2.75 μm apart could trap a single particle in two dimensions. The optical trapping of multiple microspheres and Escherichia coli bacterial cells was demonstrated proving that the lensed multicore fibre has the potential to be used to trap cells in biological experiments. The active manipulation of trapped 2 μm microspheres was also demonstrated through the rotation of the input polarisation to the multicore fibre. Finally, work towards creating a “turn-key” optical trapping device was demonstrated through the fabrication of a fully integrated multicore fibre device using an ultrafast laser-inscribed fan-out to couple light into each core. Single mode operation of the device was demonstrated at 1550 nm, using a weaker lensed MCF device. The two dimensional trapping of 4.5 μm polystyrene microspheres was shown in an array of peaks spaced 11.2 μm apart at a distance of 400 ± 25 μm from the end of the fibre

Sensing using Specialty Optical Fibers

Fiber optic based sensing is a growing field with many applications in civil and aerospace engineering, oil and gas industries, and particularly in harsh environments where electronics are not able to function. Optical fibers can be easily integrated into structures, are immune to electromagnetic interference, can be interrogated from remote distances, and can be multiplexed for distributed measurements. Because of these properties, specialty fiber designs and devices are being explored for sensing temperature, strain, pressure, curvature, refractive index, and more. Here we show a detailed analysis of a multicore fiber (MCF) for sensing, including its design and optimization in simulation, as well as experimental operation when used as sensor. The multicore fiber sensor\u27s performance as a function of temperature, strain, bending, and acoustic waves are all explored. The MCF sensors are shown to be able to withstand temperatures up to 1000°C, making them suitable to be harsh environment sensors. Additionally, a simple method for increasing the sensitivity of the MCF to longitudinal force is shown to multiple the sensitivity of the MCF sensor by a factor of seven. Also, a configuration for decoupling force and temperature will be presented. Finally, a developing all-fiber device, a photonic lantern, will be shown in conjunction with the MCF in order to increase sensitivity, add directional sensitivity, and lower the cost of the sensor interrogation for bending measurements. In addition to the multicore fiber, an analysis of anti-resonant hollow core fiber (ARHCF) is also presented. The fibers\u27 design-dependent propagation losses are explored, as well as their higher order mode content. Also, a potential application of an ARHCF for an in-fiber Raman air sensor is introduced, and the design optimization in simulation is shown

High-speed and Robust Integrated Silicon Nanophotonics for On-Chip Interconnects

Optical interconnects offer advantages over electrical interconnects such as higher bandwidth, low power, reduced interconnects delay, and immunity to electro-magnetic interference and signal crosstalk. However, in order for optical interconnects to be widely adopted, the technology must be made cost effective and must be simple to implement with CMOS electronics. Silicon photonics offers a great promise due to its inexpensive material and its compatibility with the current CMOS fabrication technology. Moreover, Silicon as a platform has the ability to integrate with different types of the optical components such as photodetector, modulator, light source, and waveguide to form a photonics integrated circuit. The goal of this work is to develop and fabricate devices that utilize a hybrid electronic-photonic integration to enable high performance optoelectronic computing and communication systems that overcome the barriers of electronics and dramatically enhance the performance of circuits and systems. We experimentally demonstrate a novel broadband optical time division multiplexer (OTDM) on a silicon chip. The system has a footprint× 700 micrometer and is inherently broadband with a bandwidth of over 100nm making it suitable for high-speed optical networks on chip. Also, we propose and fabricate a novel design to demultiplex the high bit rates of OTDM data using two differentially operated 5Gb/s modulators. Moreover, we propose a high-speed hybrid optical-time-division-multiplexing (OTDM) and wavelength-division-multiplexing (WDM) system that seamlessly generates high bit-rate data (\u3e200Gbit/s) from a low speed (5Gbit/s) quantum-dot mode locked laser pulse source. By utilizing time and wavelength domains, the proposed design is a promising solution for high-speed, compact and low-power consumption optical networks on chip. And finally, we experimentally demonstrate a robust, low insertion loss, compact Silicon ring resonator electro-optic modulator for Binary Phase Shift Key (BPSK) coding/decoding that encodes data in the phase of light. Our design improves significantly over recently demonstrated PSK modulator designs in terms of insertion loss and stability

Improving the Performance of SDM-EON Through Demand Prioritization: A Comprehensive Analysis

This paper studies the impact of demand-prioritization on Space-Division Multiplexing Elastic Optical Networks (SDM-EON). For this purpose, we solve the static Routing, Modulation Level, Spatial Mode, and Spectrum Assignment (RMLSSA) problem using 34 different explainable demand-prioritization strategies. Although previous works have applied heuristics or meta-heuristics to perform demand-prioritization, they have not focused on identifying the best prioritization strategies, their inner operation, and the implications behind their good performance by thorough profiling and impact analysis. We focus on a comprehensive analysis identifying the best explainable strategies to sort network demands in SDM-EON, considering the physical-layer impairments found in optical communications. Also, we show that simply using the common shortest path routing might lead to higher resource requirements. Extensive simulation results show that up to 8.33% capacity savings can be achieved on average by balanced routing, up to a 16.69% capacity savings can be achieved using the best performing demand-prioritization strategy compared to the worst-performing ones, the most used demand-prioritization strategy in the literature (serving demands with higher bandwidth requirements first) is not the best-performing one but the one sorting based on the path lengths, and using double-criteria strategies to break ties is key for a good performance. These results are relevant showing that a good combination of routing and demand-prioritization heuristics impact significantly on network performance. Additionally, they increase the understanding about the inner workings of good heuristics, a valuable knowledge when network settings forbid using more computationally complex approaches

The ultrafast laser inscription of photonic devices for integrated optical applications

A study of some key areas in which ultrafast laser inscription may usefully be employed is presented. The thesis includes waveguide inscription in a variety of substrates including passive glass, doped glass and a nonlinear crystal. The work contained can be split into three studies, with some overlap between them. Firstly fused silica glass is used, both in planar substrates and as flat fibre, for the inscription of two sensing elements. The planar substrate is used for a device similar in design to a side-polished fibre and the flat fibre is used for the fabrication of a Bragg grating waveguide array. In the second study, waveguides are inscribed in the nonlinear crystal monoclinic bismuth borate, and used for guided mode second harmonic generation. A novel waveguide design is employed to increase overlap between the pump and second harmonic waveguide modes. The remainder of the thesis investigates the applicability of ultrafast laser inscription to the fabrication of compact modelocked lasers. Lasing is demonstrated, both continuous wave and modelocked, using a laser inscribed erbium doped bismuthate glass waveguide as the gain element. A study is then undertaken into methods of integrating carbon nanotubes, used as saturable absorbers to modelock lasers, into laser inscribed waveguides