Analysis of ISSQ/IDDQ testing implementation and circuit partitioning in CMOS cell-based design

© 1996 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.Difference between ISSQ and IDDQ testing strategies is presented, discussing the dependency of area overhead and sensing speed on the technology. The current sensor implementation style suitable for cell-based design methodology or semi-custom design style is proposed Experimental results for each strategy are discussed. Finally, different types of partitioning strategies are showed, taken into account the parallelism of the gates.Peer ReviewedPostprint (published version

IDDQ testing of a CMOS first order sigma-delta modulator of an 8-bit oversampling ADC

This work presents IDDQ testing of a CMOS first order sigma-delta modulator of an 8-bit oversampling analog-to-digital converter using a built-in current sensor [BICS]. Gate-drain, source-drain, gate-source and gate-substrate bridging faults are injected using fault injection transistors. All the four faults cause varying fault currents and are successfully detected by the BICS at a good operation speed. The BICS have a negligible impact on the performance of the modulator and an external pin is provided to completely cut-off the BICS from the modulator. The modulator was designed and fabricated in 1.5 μm n-well CMOS process. The decimator was designed on Altera\u27s FLEXE20K board using Verilog. The modulator and decimator were assembled together to form a sigma-delta ADC

Iddq testing of a CMOS 10-bit charge scaling digital-to-analog converter

This work presents an effective built-in current sensor (BICS), which has a very small impact on the performance of the circuit under test (CUT). The proposed BICS works in two-modes the normal mode and the test mode. In the normal mode the BICS is isolated from the CUT due to which there is no performance degradation of the CUT. In the testing mode, our BICS detects the abnormal current caused by permanent manufacturing defects. Further more our BICS can also distinguish the type of defect induced (Gate-source short, source-drain short and drain-gate short). Our BICS requires neither an external voltage source nor current source. Hence the BICS requires less area and is more efficient than the conventional current sensors. The circuit under test is a 10-bit digital to analog converter using charge-scaling architecture

A Behavioral Model of a Built-in Current Sensor for IDDQ Testing

IDDQ testing is one of the most effective methods for detecting defects in integrated circuits. Higher leakage currents in more advanced semiconductor technologies have reduced the resolution of IDDQ test. One solution is to use built-in current sensors. Several sensor techniques for measuring the current based on the magnetic field or voltage drop across the supply line have been proposed. In this work, we develop a behavioral model for a built-in current sensor measuring voltage drop and use this model to better understand sensor operation, identify the effect of different parameters on sensor resolution, and suggest design modifications to improve future sensor performance

Voltage sensing based built-in current sensor for IDDQ test

Quiescent current leakage test of the VDD supply (IDDQ Test) has been proven an effective way to screen out defective chips in manufacturing of Integrated Circuits (IC). As technology advances, the traditional IDDQ test is facing more and more challenges. In this research, a practical built-in current sensor (BICS) is proposed and the design is verified by three generations of test chips. The BICS detects the signal by sensing the voltage drop on supply lines of the circuit under test (CUT). Then the sensor performs analog-to-digital conversion of the input signal using a stochastic process with scan chain readout. Self-calibration and digital chopping are used to minimize offset and low frequency noise and drift. This non-invasive procedure avoids any performance degradation of the CUT. The measurement results of test chips are presented. The sensor achieves a high IDDQ resolution with small chip area overhead. This will enable IDDQ of future technology generations

Programmable CMOS Analog-to-Digital Converter Design and Testability

In this work, a programmable second order oversampling CMOS delta-sigma analog-to-digital converter (ADC) design in 0.5µm n-well CMOS processes is presented for integration in sensor nodes for wireless sensor networks. The digital cascaded integrator comb (CIC) decimation filter is designed to operate at three different oversampling ratios of 16, 32 and 64 to give three different resolutions of 9, 12 and 14 bits, respectively which impact the power consumption of the sensor nodes. Since the major part of power consumed in the CIC decimator is by the integrators, an alternate design is introduced by inserting coder circuits and reusing the same integrators for different resolutions and oversampling ratios to reduce power consumption. The measured peak signal-to-noise ratio (SNR) for the designed second order delta-sigma modulator is 75.6dB at an oversampling ratio of 64, 62.3dB at an oversampling ratio of 32 and 45.3dB at an oversampling ratio of 16. The implementation of a built-in current sensor (BICS) which takes into account the increased background current of defect-free circuits and the effects of process variation on ΔIDDQ testing of CMOS data converters is also presented. The BICS uses frequency as the output for fault detection in CUT. A fault is detected when the output frequency deviates more than ±10% from the reference frequency. The output frequencies of the BICS for various model parameters are simulated to check for the effect of process variation on the frequency deviation. A design for on-chip testability of CMOS ADC by linear ramp histogram technique using synchronous counter as register in code detection unit (CDU) is also presented. A brief overview of the histogram technique, the formulae used to calculate the ADC parameters, the design implemented in 0.5µm n-well CMOS process, the results and effectiveness of the design are described. Registers in this design are replaced by 6T-SRAM cells and a hardware optimized on-chip testability of CMOS ADC by linear ramp histogram technique using 6T-SRAM as register in CDU is presented. The on-chip linear ramp histogram technique can be seamlessly combined with ΔIDDQ technique for improved testability, increased fault coverage and reliable operation

On the deployment of on-chip noise sensors

The relentless technology scaling has led to significantly reduced noise margin and complicated functionalities. As such, design time techniques per se are less likely to ensure power integrity, resulting in runtime voltage emergencies. To alleviate the issue, recently several works have shed light on the possibilities of dynamic noise management systems. Most of these works rely on on-chip noise sensors to accurately capture voltage emergencies. However, they all assume that the placement of the sensors is given. It remains an open problem in the literature how to optimally place a given number of noise sensors for best voltage emergency detection. The problem of noise sensor placement is defined at first along with a novel sensing quality metric (SQM) to be maximized. The threshold voltage for noise sensors to report emergencies serves as a critical tuning knob between the system failure rate and false alarms. The problem of minimizing the system alarm rate subject to a given system failure rate constraint is formulated. It is further shown that with the help of IDDQ measurements during testing which reveal process variation information, it is possible and efficient to compute a per-chip optimal threshold voltage threshold. In the third chapter, a novel framework to predict the resonance frequency using existing on-chip noise sensors, based on the theory of 1-bit compressed sensing is proposed. The proposed framework can help to achieve the resonance frequency of individual chips so as to effectively avoid resonance noise at runtime --Abstract, page iii

Testing a CMOS operational amplifier circuit using a combination of oscillation and IDDQ test methods

This work presents a case study, which attempts to improve the fault diagnosis and testability of the oscillation testing methodology applied to a typical two-stage CMOS operational amplifier. The proposed test method takes the advantage of good fault coverage through the use of a simple oscillation based test technique, which needs no test signal generation and combines it with quiescent supply current (IDDQ) testing to provide a fault confirmation. A built in current sensor (BICS), which introduces insignificant performance degradation of the circuit-under-test (CUT), has been utilized to monitor the power supply quiescent current changes in the CUT. The testability has also been enhanced in the testing procedure using a simple fault-injection technique. The approach is attractive for its simplicity, robustness and capability of built-in-self test (BIST) implementation. It can also be generalized to the oscillation based test structures of other CMOS analog and mixed-signal integrated circuits. The practical results and simulations confirm the functionality of the proposed test method

Development of a CMOS IDDq Testing Environment

A majority of defects found in CMOS technology display elevated quiescent current magnitudes but still may pass functionality tests. By monitoring this power supply current, defect coverage can be elevated past the traditional stuck-at-fault coverage. This study provides a test methodology centered around current supply monitoring. By analyzing fabrication data, defect models, built-in current sensors, current and delay estimation, test set generation, and the QTAG standard, a technique is developed for CMOS integrated circuit testing. A built-in current sensor is presented, which through simulation, exhibits fast detection time. Novel techniques to enhance this time are also presented