Cross-bidge Kelvin resistor (CBKR) structures for measurement of low contact resistances

A convenient test structure for measurement of the specific contact resistance (ρc) of metal-semiconductor junctions is the CBKR structure. During last few decades the parasitic factors which may strongly affect the measurements accuracy for ρc < 10-6 Ω • cm2 have been sufficiently discussed and the minimum of the ρc to be measured using CBKR structures was estimated. We fabricated a set of CBKR structures with different geometries to confirm this limit experimentally. These structures were manufactured for metal-to-metal contacts. It was found that the extracted CBKR values were determined by dimensions of the two-metal stack in the contact area and sheet resistances of the metals used. \ud Index Terms—Contact resistance, cross-bridge Kelvin resistor (CBKR), sheet resistance, test structures, metal, silico

High-efficiency robust perovskite solar cells on ultrathin flexible substrates.

Wide applications of personal consumer electronics have triggered tremendous need for portable power sources featuring light-weight and mechanical flexibility. Perovskite solar cells offer a compelling combination of low-cost and high device performance. Here we demonstrate high-performance planar heterojunction perovskite solar cells constructed on highly flexible and ultrathin silver-mesh/conducting polymer substrates. The device performance is comparable to that of their counterparts on rigid glass/indium tin oxide substrates, reaching a power conversion efficiency of 14.0%, while the specific power (the ratio of power to device weight) reaches 1.96 kW kg(-1), given the fact that the device is constructed on a 57-μm-thick polyethylene terephthalate based substrate. The flexible device also demonstrates excellent robustness against mechanical deformation, retaining &gt;95% of its original efficiency after 5,000 times fully bending. Our results confirmed that perovskite thin films are fully compatible with our flexible substrates, and are thus promising for future applications in flexible and bendable solar cells

A UV Sensitive Integrated Micromegas with Timepix Readout

This article presents a detector system consisting of three components, a CMOS imaging array, a gaseous-detector structure with a Micromegas layout and a UV-photon sensitive CsI reflective photocathode. All three elements have been monolithically integrated using simple post-processing steps. The Micromegas structure and the CMOS imaging chip are not impacted by the CsI deposition. The detector operated reliably in He/isobutane mixtures and attained charge gains with single photons up to a level of 6 \cdot 10^4. The Timepix CMOS array permitted high resolution imaging of single UV-photons. The system has an MTF50 of 0.4 lp/pixel which corresponds to app. 7 lp/mm.Comment: 4 pages with 8 figures. Submitted to Nucl. Instr. and Meth. A (Elsevier) for proceedings of VCI 2010

SRF Cavity Fabrication and Materials

The technological and metallurgical requirements of material for highgradient superconducting cavities are described. High-purity niobium, as the preferred metal for the fabrication of superconducting accelerating cavities, should meet exact specifications. The content of interstitial impurities such as oxygen, nitrogen, and carbon must be below 10{\mu}g/g. The hydrogen content should be kept below 2{\mu}g/g to prevent degradation of the Q-value under certain cool-down conditions. The material should be free of flaws (foreign material inclusions or cracks and laminations) that can initiate a thermal breakdown. Defects may be detected by quality control methods such as eddy current scanning and identified by a number of special methods. Conventional and alternative cavity fabrication methods are reviewed. Conventionally, niobium cavities are fabricated from sheet niobium by the formation of half-cells by deep drawing, followed by trim machining and Electron-Beam Welding (EBW). The welding of half-cells is a delicate procedure, requiring intermediate cleaning steps and a careful choice of weld parameters to achieve full penetration of the joints. The equator welds are particularly critical. A challenge for a welded construction is the tight mechanical and electrical tolerances. These can be maintained by a combination of mechanical and radio-frequency measurements on halfcells and by careful tracking of weld shrinkage. The established procedure is suitable for large series production. The main aspects of quality assurance management are mentioned. Another cavity fabrication approach is slicing discs from the ingot and producing cavities by deep drawing and EBW. Accelerating gradients at the level of 35-45 MV.m-1 can be achieved by applying Electropolishing (EP) treatment....Comment: 37 pages, contribution to the CAS-CERN Accelerator School: Superconductivity for Accelerators, Erice, Italy, 24 April - 4 May 2013, edited by R. Baile

Graphene Field Effect Transistors: Diffusion-Drift Theory

Based on explicit solution of current continuity equation in the graphene FET's channel the semi-classical diffusion-drift description of the carrier transport and I-V characteristics model has been developed. Role of rechargeable defects (interface traps) near or at the interface between graphene and insulated layers has also described.Comment: 24 pages, 13 figures, a chapter in "Graphene, Theory, Research and Applications", INTEC