Photonic integration enabling new multiplexing concepts in optical board-to-board and rack-to-rack interconnects

New broadband applications are causing the datacenters to proliferate, raising the bar for higher interconnection speeds. So far, optical board-to-board and rack-to-rack interconnects relied primarily on low-cost commodity optical components assembled in a single package. Although this concept proved successful in the first generations of optical-interconnect modules, scalability is a daunting issue as signaling rates extend beyond 25 Gb/s. In this paper we present our work towards the development of two technology platforms for migration beyond Infiniband enhanced data rate (EDR), introducing new concepts in board-to-board and rack-to-rack interconnects. The first platform is developed in the framework of MIRAGE European project and relies on proven VCSEL technology, exploiting the inherent cost, yield, reliability and power consumption advantages of VCSELs. Wavelength multiplexing, PAM-4 modulation and multi-core fiber (MCF) multiplexing are introduced by combining VCSELs with integrated Si and glass photonics as well as BiCMOS electronics. An in-plane MCF-to-SOI interface is demonstrated, allowing coupling from the MCF cores to 340x400 nm Si waveguides. Development of a low-power VCSEL driver with integrated feed-forward equalizer is reported, allowing PAM-4 modulation of a bandwidth-limited VCSEL beyond 25 Gbaud. The second platform, developed within the frames of the European project PHOXTROT, considers the use of modulation formats of increased complexity in the context of optical interconnects. Powered by the evolution of DSP technology and towards an integration path between inter and intra datacenter traffic, this platform investigates optical interconnection system concepts capable to support 16QAM 40GBd data traffic, exploiting the advancements of silicon and polymer technologies

A 90 nm CMOS 16 Gb/s Transceiver for Optical Interconnects

Interconnect architectures which leverage high-bandwidth optical channels offer a promising solution to address the increasing chip-to-chip I/O bandwidth demands. This paper describes a dense, high-speed, and low-power CMOS optical interconnect transceiver architecture. Vertical-cavity surface-emitting laser (VCSEL) data rate is extended for a given average current and corresponding reliability level with a four-tap current summing FIR transmitter. A low-voltage integrating and double-sampling optical receiver front-end provides adequate sensitivity in a power efficient manner by avoiding linear high-gain elements common in conventional transimpedance-amplifier (TIA) receivers. Clock recovery is performed with a dual-loop architecture which employs baud-rate phase detection and feedback interpolation to achieve reduced power consumption, while high-precision phase spacing is ensured at both the transmitter and receiver through adjustable delay clock buffers. A prototype chip fabricated in 1 V 90 nm CMOS achieves 16 Gb/s operation while consuming 129 mW and occupying 0.105 mm^2

Fabrication and characterization of integrable GaAs-based high-contrast grating reflector and Fabry-Pérot filter array with GaInP sacrificial layer

Integrable GaAs-based high-contrast gratings (HCGs) are fabricated and characterized, targeting applications in high-speed vertical-cavity surface-emitting lasers (VCSELs). A Ga 0.51 In 0.49 P sacrificial layer beneath the GaAs layer is employed to create a low index surrounding HCG strips by selective etching. Experimental results show that the finite-size HCG has a reflectivity of 93% from 1270 to 1330 nm for the transverse magnetic polarization, which is consistent with the calculated results. An HCG-based Fabry-Perot filter array formed by the different HCGs, air gap, and GaAs substrate is demonstrated. The measured resonance wavelengths of the filter arrays are consistent with the theoretical results, which implies that the resonance wavelength of such filters can be tuned by parameters of the HCG itself

High-Speed VCSELs with Strong Confinement of Optical Fields and Carriers

We present the design, fabrication, and performance of our latest generation high-speed oxide-confined 850-nm verticalcavity surface-emitting lasers. Excellent high-speed properties are obtained by strong confinement of optical fields and carriers. Highspeed modulation is facilitated by using the shortest possible cavity length of one half wavelength and placing oxide apertures close to the active region to efficiently confine charge carriers. The resulting strong current confinement boosts internal quantum efficiency, leading to low threshold currents, high wall-plug efficiency, and state-of-the-art high-speed properties at low bias currents. The temperature dependent static and dynamic performance is analyzed by current-power-voltage and small-signal modulation measurements

Optoelectronic devices and packaging for information photonics

This thesis studies optoelectronic devices and the integration of these components onto optoelectronic multi chip modules (OE-MCMs) using a combination of packaging techniques. For this project, (1×12) array photodetectors were developed using PIN diodes with a GaAs/AlGaAs strained layer structure. The devices had a pitch of 250μm, operated at a wavelength of 850nm. Optical characterisation experiments of two types of detector arrays (shoe and ring) were successfully performed. Overall, the shoe devices achieved more consistent results in comparison with ring diodes, i.e. lower dark current and series resistance values. A decision was made to choose the shoe design for implementation into the high speed systems demonstrator. The (1x12) VCSEL array devices were the optical sources used in my research. This was an identical array at 250μm pitch configuration used in order to match the photodetector array. These devices had a wavelength of 850nm. Optoelectronic testing of the VCSEL was successfully conducted, which provided good beam profile analysis and I-V-P measurements of the VCSEL array. This was then implemented into a simple demonstrator system, where eye diagrams examined the systems performance and characteristics of the full system and showed positive results. An explanation was given of the following optoelectronic bonding techniques: Wire bonding and flip chip bonding with its associated technologies, i.e. Solder, gold stud bump and ACF. Also, technologies, such as ultrasonic flip chip bonding and gold micro-post technology were looked into and discussed. Experimental work implementing these methods on packaging the optoelectronic devices was successfully conducted and described in detail. Packaging of the optoelectronic devices onto the OEMCM was successfully performed. Electrical tests were successfully carried out on the flip chip bonded VCSEL and Photodetector arrays. These results verified that the devices attached on the MCM achieved good electrical performance and reliable bonding. Finally, preliminary testing was conducted on the fully assembled OE-MCMs. The aim was to initially power up the mixed signal chip (VCSEL driver), and then observe the VCSEL output