Signal and System Design for Wireless Power Transfer : Prototype, Experiment and Validation

A new line of research on communications and signals design for Wireless Power Transfer (WPT) has recently emerged in the communication literature. Promising signal strategies to maximize the power transfer efficiency of WPT rely on (energy) beamforming, waveform, modulation and transmit diversity, and a combination thereof. To a great extent, the study of those strategies has so far been limited to theoretical performance analysis. In this paper, we study the real over-the-air performance of all the aforementioned signal strategies for WPT. To that end, we have designed, prototyped and experimented an innovative radiative WPT architecture based on Software-Defined Radio (SDR) that can operate in open-loop and closed-loop (with channel acquisition at the transmitter) modes. The prototype consists of three important blocks, namely the channel estimator, the signal generator, and the energy harvester. The experiments have been conducted in a variety of deployments, including frequency flat and frequency selective channels, under static and mobility conditions. Experiments highlight that a channeladaptive WPT architecture based on joint beamforming and waveform design offers significant performance improvements in harvested DC power over conventional single-antenna/multiantenna continuous wave systems. The experimental results fully validate the observations predicted from the theoretical signal designs and confirm the crucial and beneficial role played by the energy harvester nonlinearity.Comment: Accepted to IEEE Transactions on Wireless Communication

Class-E rectifiers and power converters: the operation of the class-E topology as a power amplifier and a rectifier with very high conversion efficiencies

In the late 70’s, the interest in reducing the value and size of reactive components moved power supply specialists to operate dc-to-dc converters at hundreds of kHz or even MHz frequencies. Passive energy storage (mainly magnetics) dominates the size of power electronics, limiting also its cost, reliability and dynamic response. Motivated by miniaturization and improved control bandwidth, they had to face the frequency-dependent turn-on and turn-off losses associated with the use of rectangular waveforms in the hard-switched topologies of that time. Similar to approaches for RF/microwave power amplifiers (PAs), the introduction of resonant circuits allowed shaping either a sinusoidal voltage or current, with parasitic reactive elements absorbed by the topology in the neighborhood of the switching frequency. The resulting resonant power converters, obtained by cascading a dc-to-ac resonant inverter with a high-frequency ac-to-dc rectifier, first transform the dc input power into controlled ac power, and then convert it back into the desired dc output [1]. This paper provides some historic notes on the operation of the class-E topology, introduced worldwide to the RF/microwave community by Nathan O. Sokal [2], as a power inverter and as a rectifier, with very high conversion efficiencies up to microwave frequencies. Recent research advances and implementations of class-E rectifiers and dc-to-dc converters at UHF and beyond are included. Offering competitive performance in terms of efficiency for RF power recovery, together with a wide bandwidth for low-loss power conversion, their potential for some modern applications is highlighted.The authors would like to acknowledge support in part by the Spanish Ministry of Economy, Industry and Competitiveness (MINECO) through TEC2014-58341-C4-1-R and TEC2017-83343-C4-1-R projects, co-funded with FEDER, and in part by Lockheed Martin Endowed Chair at the University of Colorado

Dual-Polarized Communication Rectenna Array for Simultaneous Wireless Information and Power Transmission

A dual-polarized communication rectenna array with high isolation and low cross polarization for simultaneous wireless information and power transmission (SWIPT) is presented. It consists of a 2 × 2 element receiving antenna array and a high efficiency rectifier based on voltage doubler topology. The receiving element is corner-fed to achieve high isolation of more than 20 dB between the dual-polarized ports, which guarantees low mutual interference between the communication and the rectifying ports. To receive enough electromagnetic (EM) wave for rectifying and meanwhile meet the communication sensitivity, this 2 × 2 array uses its 2 × 2 vertical polarization ports and 1 × 2 horizontal polarization ports for power rectifying, and the rest 1 × 2 horizontal polarization ports for communication. For the communication port, the measured gain is 10.9 dBi and the cross polarization is less than -20 dB. The performance of the whole communication rectenna array has been measured, where a 2 × 4 circularly-polarized array with a gain of 17.5 dBi, settled 1 meter away is used as the transmitter. Measured results show that the system achieves a peak microwave - direct circuit (mw-dc) conversion efficiency of 74.9 % for the CW signal, and 67 % for the QPSK signal with 10 MHz channel bandwidth on the load of 345 Ω at 2.58 GHz operating frequency

High Efficiency and High Sensitivity Wireless Power Transfer and Wireless Power Harvesting Systems.

In this dissertation, several approaches to improve the efficiency and sensitivity of wireless power transfer and wireless power harvesting systems, and to enhance their performance in fluctuant and unpredictable circumstances are described. Firstly, a nonlinear resonance circuit described by second-order differential equation with cubic-order nonlinearities (the Duffing equation) is developed. The Duffing nonlinear resonance circuit has significantly wider bandwidth as compared to conventional linear resonators, while achieving a similar level of amplitude. The Duffing resonator is successfully applied to the design of WPT systems to improve their tolerance to coupling factor variations stemming from changes of transmission distance and alignment of coupled coils. Subsequently, a high sensitivity wireless power harvester which collects RF energy from AM broadcast stations for powering the wireless sensors in structural health monitoring systems is introduced. The harvester demonstrates the capability of providing net RF power within 6 miles away from a local 50 kW AM station. The aforementioned Duffing resonator is also used in the design of WPH systems to improve their tolerance to frequency misalignment resulting from component aging, coupling to surrounding objects or variations of environmental conditions (temperature, humidity, etc.). At last, a rectifier array circuit with an adaptive power distribution method for wide dynamic range operation is developed. Adaptive power distribution is achieved through impedance transformation of the rectifiers’ nonlinear impedance with a passive network. The rectifier array achieves high RF-to-DC efficiency within a wide range of input power levels, and is useful in both WPT and WPH applications where levels of the RF power collected by the receiver are subject to unpredictable fluctuations.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/133338/1/tinyfish_1.pd

Matching Network Elimination in Broadband Rectennas for High-Efficiency Wireless Power Transfer and Energy Harvesting

Impedance matching networks for nonlinear devices such as amplifiers and rectifiers are normally very challenging to design, particularly for broadband and multiband devices. A novel design concept for a broadband high-efficiency rectenna without using matching networks is presented in this paper for the first time. An off-center-fed dipole antenna with relatively high input impedance over a wide frequency band is proposed. The antenna impedance can be tuned to the desired value and directly provides a complex conjugate match to the impedance of a rectifier. The received RF power by the antenna can be delivered to the rectifier efficiently without using impedance matching networks; thus, the proposed rectenna is of a simple structure, low cost, and compact size. In addition, the rectenna can work well under different operating conditions and using different types of rectifying diodes. A rectenna has been designed and made based on this concept. The measured results show that the rectenna is of high power conversion efficiency (more than 60%) in two wide bands, which are 0.9-1.1 and 1.8-2.5 GHz, for mobile, Wi-Fi, and ISM bands. Moreover, by using different diodes, the rectenna can maintain its wide bandwidth and high efficiency over a wide range of input power levels (from 0 to 23 dBm) and load values (from 200 to 2000 Ω). It is, therefore, suitable for high-efficiency wireless power transfer or energy harvesting applications. The proposed rectenna is general and simple in structure without the need for a matching network hence is of great significance for many applications

Miniaturized Microwave Devices and Antennas for Wearable, Implantable and Wireless Applications

This thesis presents a number of microwave devices and antennas that maintain high operational efficiency and are compact in size at the same time. One goal of this thesis is to address several miniaturization challenges of antennas and microwave components by using the theoretical principles of metamaterials, Metasurface coupling resonators and stacked radiators, in combination with the elementary antenna and transmission line theory. While innovating novel solutions, standards and specifications of next generation wireless and bio-medical applications were considered to ensure advancement in the respective scientific fields. Compact reconfigurable phase-shifter and a microwave cross-over based on negative-refractive-index transmission-line (NRI-TL) materialist unit cells is presented. A Metasurface based wearable sensor architecture is proposed, containing an electromagnetic band-gap (EBG) structure backed monopole antenna for off-body communication and a fork shaped antenna for efficient radiation towards the human body. A fully parametrized solution for an implantable antenna is proposed using metallic coated stacked substrate layers. Challenges and possible solutions for off-body, on-body, through-body and across-body communication have been investigated with an aid of computationally extensive simulations and experimental verification. Next, miniaturization and implementation of a UWB antenna along with an analytical model to predict the resonance is presented. Lastly, several miniaturized rectifiers designed specifically for efficient wireless power transfer are proposed, experimentally verified, and discussed. The study answered several research questions of applied electromagnetic in the field of bio-medicine and wireless communication.Comment: A thesis submitted for the degree of Ph

Düşük güçte çalışan sensörler i̇çi̇n bi̇r radyo frekansı enerji̇ hasatlayıcı devre tasarımı ve geli̇şti̇ri̇lmesi̇

This thesis presents a systematic design and implementation of a rectenna. As a beginning, a receiving antenna is proposed. In the design of the receiving antenna, a fractal topology is utilized to widen the antenna bandwidth. Moreover, a rectifier circuit with a proposed dualband matching technique is realized to aggregate the DC power. Ultimately, the broadband fractal antenna and the proposed dual-band rectifier circuit have been assembled to realize the rectenna. In addition, a simple RF spectrum study and a field measurement are conducted to obtain a better understanding of the available electric field density in the Middle East Technical University–Northern Cyprus Campus. Finally, the energy harvesting capability of the proposed rectenna has been verified in both controlled environment (laboratory) and ambient. As a result of the laboratory measurements, the proposed rectenna yields the highest RF-toDC conversion efficiency of 51.9% when the total power density of the two tone signal is 11.1 µW/cm2 . As a result of the ambient measurements, the proposed rectenna features an openvoltage in the range of 195–417 mV in the ambient when the highest electric field densities are 4.137 V/m and 1.818 V/m from the standards of GSM-900 and 3G (UMTS), respectivelyBu tez, bir dogrultucu antenin sistematik tasarımını ve uygunlamasını sunmaktadır. İlk olarak, alıcı antenin bant genişligini arttırmak için fraktal topoloji ile tasarımına yer verilir. Bunun yanında, önerilen çift bantlı empedans uyumlaştırma özelligine sahip bir doğrultucu devresinin tasarımı ele alınır. Son olarak, geniş bantlı alıcı anten ile önerilen dogrultucu devre enerji hasatlayıcı devreyi gerçekleştirmek için birleştirilir. Bunlara ek olarak, Orta Dogu Teknik Üniversitesi Kuzey Kıbrıs Kampüsü’ndeki mevcut elektriksel alan yogunluğunun belirlen mesi için yapılan ölçümler ve sonuçları sunulur. Önerilen dogrultucu anten hem laboratu varda hem de dış ortamda bulunan RF sinyalleri ile test edilir. Laboratuvar ölçümlerinin sonucunda, dogrultucu antenin, iki ton RF sinyalinden gelen ve toplam güç yoğunluğunun 11.1 µW/cm2 oldugu bir test düzeneğinde, sağlayabildiği en yüksek dönüşüm verimliliği % 51.9 olarak kaydedilmiştir. Dış ortamdaki ölçümler sonucunda, dogrultucu antenin elektriksel alan yogunluklarının 4.137 V /m ile 1.818 V/m arasında degiştiği bir dış ortamda, 195 mV ile 417 mV arasında degişen yüksüz çıkış voltajı sağladığı kaydedilmiştir.M.S. - Master of Scienc

Performance evaluation of 5G millimeter-wave cellular access networks using a capacity-based network deployment tool

The next fifth generation (5G) of wireless communication networks comes with a set of new features to satisfy the demand of data-intensive applications: millimeter-wave frequencies, massive antenna arrays, beamforming, dense cells, and so forth. In this paper, we investigate the use of beamforming techniques through various architectures and evaluate the performance of 5G wireless access networks, using a capacity-based network deployment tool. This tool is proposed and applied to a realistic area in Ghent, Belgium, to simulate realistic 5G networks that respond to the instantaneous bit rate required by the active users. The results show that, with beamforming, 5G networks require almost 15% more base stations and 4 times less power to provide more capacity to the users and the same coverage performances, in comparison with the 4G reference network. Moreover, they are 3 times more energy efficient than the 4G network and the hybrid beamforming architecture appears to be a suitable architecture for beamforming to be considered when designing a 5G cellular network