Hands-on reconfigurable robotic surgical instrument holder arm

Abstract: The use of conventional surgical tool holders requires an assistant during positioning and adjustment due to the lack of weight compensation. In this paper, we introduce a robotic arm system with hands-on control approach. The robot incorporates a force sensor at the end effector which realises tool weight compensation as well as hands-on manipulation. On the operating table, the required workspace can be tight due to a number of instruments required. There are situations where the surgical tool is at the desired location but the holder arm pose is not ideal due to space constraints or obstacles. Although the arm is a non-redundant robot because of the limited degrees of freedom, the pseudo-null-space inverse kinematics can be used to constrain a particular joint of the robot to a specific angle while the other joints compensate in order to minimise the tool movement. This allows operator to adjust the arm configuration conveniently together with the weight compensation. Experimental results demonstrated that our robotic arm can maintain the tool position during reconfiguration significantly more stably than a conventional one

From Concept to Market: Surgical Robot Development

Surgical robotics and supporting technologies have really become a prime example of modern applied information technology infiltrating our everyday lives. The development of these systems spans across four decades, and only the last few years brought the market value and saw the rising customer base imagined already by the early developers. This chapter guides through the historical development of the most important systems, and provide references and lessons learnt for current engineers facing similar challenges. A special emphasis is put on system validation, assessment and clearance, as the most commonly cited barrier hindering the wider deployment of a system

Cable-driven parallel mechanisms for minimally invasive robotic surgery

Minimally invasive surgery (MIS) has revolutionised surgery by providing faster recovery times, less post-operative complications, improved cosmesis and reduced pain for the patient. Surgical robotics are used to further decrease the invasiveness of procedures, by using yet smaller and fewer incisions or using natural orifices as entry point. However, many robotic systems still suffer from technical challenges such as sufficient instrument dexterity and payloads, leading to limited adoption in clinical practice. Cable-driven parallel mechanisms (CDPMs) have unique properties, which can be used to overcome existing challenges in surgical robotics. These beneficial properties include high end-effector payloads, efficient force transmission and a large configurable instrument workspace. However, the use of CDPMs in MIS is largely unexplored. This research presents the first structured exploration of CDPMs for MIS and demonstrates the potential of this type of mechanism through the development of multiple prototypes: the ESD CYCLOPS, CDAQS, SIMPLE, neuroCYCLOPS and microCYCLOPS. One key challenge for MIS is the access method used to introduce CDPMs into the body. Three different access methods are presented by the prototypes. By focusing on the minimally invasive access method in which CDPMs are introduced into the body, the thesis provides a framework, which can be used by researchers, engineers and clinicians to identify future opportunities of CDPMs in MIS. Additionally, through user studies and pre-clinical studies, these prototypes demonstrate that this type of mechanism has several key advantages for surgical applications in which haptic feedback, safe automation or a high payload are required. These advantages, combined with the different access methods, demonstrate that CDPMs can have a key role in the advancement of MIS technology.Open Acces

Snake-Like Robots for Minimally Invasive, Single Port, and Intraluminal Surgeries

The surgical paradigm of Minimally Invasive Surgery (MIS) has been a key driver to the adoption of robotic surgical assistance. Progress in the last three decades has led to a gradual transition from manual laparoscopic surgery with rigid instruments to robot-assisted surgery. In the last decade, the increasing demand for new surgical paradigms to enable access into the anatomy without skin incision (intraluminal surgery) or with a single skin incision (Single Port Access surgery - SPA) has led researchers to investigate snake-like flexible surgical devices. In this chapter, we first present an overview of the background, motivation, and taxonomy of MIS and its newer derivatives. Challenges of MIS and its newer derivatives (SPA and intraluminal surgery) are outlined along with the architectures of new snake-like robots meeting these challenges. We also examine the commercial and research surgical platforms developed over the years, to address the specific functional requirements and constraints imposed by operations in confined spaces. The chapter concludes with an evaluation of open problems in surgical robotics for intraluminal and SPA, and a look at future trends in surgical robot design that could potentially address these unmet needs.Comment: 41 pages, 18 figures. Preprint of article published in the Encyclopedia of Medical Robotics 2018, World Scientific Publishing Company www.worldscientific.com/doi/abs/10.1142/9789813232266_000

복강경 수술 로봇 시스템의 활용도 향상을 위한 추가적인 마스터 인터페이스 개발과 이를 이용한 응용 시스템 개발 연구

학위논문 (박사)-- 서울대학교 대학원 공과대학 협동과정 바이오엔지니어링전공, 2017. 8. Sungwan Kim.Robot-assisted laparoscopic surgery offers several advantages compared to open surgery and conventional minimally invasive surgery. However, important issues which need to be resolved are the complexity of current operation room environment for laparoscopic robotic surgery and demand for a larger operation room. To overcome these issues, additional interfaces based on Hands-On-Throttle-And-Stick (HOTAS) concept which can be simply attached and integrated with master interface of da Vinci surgical robot system were proposed. HOTAS controller is widely used for flight control in the aerospace field which can manipulate hundreds of functions and provide feedback to the pilot on flight conditions. The implementation of HOTAS controller significantly reduced the complexity of flights and reduced the number of pilots required in a cockpit from two to one. In this study, to provide above benefits to the operation room for robotic laparoscopic surgery, two types of additional interfaces are proposed. Proposed additional interfaces can be easily manipulated by the surgeons index finger, which is currently operated only by finger clutch buttons, and therefore enable the surgeon to use multiple functions. Initially, a novel master interface (NMI) was developed. The NMI mainly consists of a 9-way switch and a microprocessor with a wireless communication module. Thus, the NMI can be also regarded as a 9-way compact HOTAS. The performance test, latency, and power consumption of the developed NMI were verified by repeated experiments. Then, an improved novel master interface (iNMI) was developed to provide more intuitive and convenient manipulation. The iNMI was developed based on a capacitive touch sensor array and a wireless microprocessor to intuitively reflect the surgeons decision. Multiple experiments were performed to evaluate the iNMI performance in terms of performance test, latency, and power consumption. In addition, two application systems based on Surgical-Operation-By-Wire (SOBW) concept are proposed in this research to enhance the function of laparoscopic surgical robot system based on clinical needs that are stated below. The size of the additional interface is small enough to be easily installed to the master tool manipulators (MTMs) of da Vinci research kit (dVRK), which was used as an operation robot arm system, to maximize convenience to the surgeon when using the additional interfaces to simultaneously manipulate the application systems with the MTMs. Firstly, a robotic assistant that can be simultaneously manipulated via a wireless controller is proposed to allow the surgeon to control the assistant instrument. This approach not only decreases surgeon fatigue by eliminating communication process with assistants, but also resolves collision between the operation robot arms and the assistant instruments that can be caused by an inexperienced assistant or miscommunication and misaligned intent between the surgeon and the assistant. The system comprises two additional interfaces, a surgical instrument with a gripper actuated by a micromotor and a 6-axis robot arm. The gripping force of the surgical instrument was comparable to that of conventional systems and was consistent even after 1,000 times of gripping motion. The workspace was calculated to be 8,397.4 cm3. Recruited volunteers were able to execute the simple peg task within the cut-off time and successfully performed the in vitro test. Secondly, a wirelessly controllable stereo endoscope system which enables simultaneous control with the operating robot arm system is proposed. This is able to remove any discontinuous surgical flow that occurs when the control is swapped between the endoscope system and the operating robot arm system, and therefore prevent problems such as increased operation time, collision among surgical instruments, and injury to patients. The proposed system consists of two additional interfaces, a four-degrees of freedom (4-DOFs) endoscope control system (ECS) and a simple three-dimensional (3D) endoscope. The 4-DOFs ECS consists of four servo motors and employs a two-parallel link structure to provide translational and fulcrum point motions to the simple 3D endoscope. The workspace was calculated to be 20,378.3 cm3, which exceeds the reference workspace. The novice volunteers were able to successfully execute the modified peg transfer task. Throughout the various verifications, it has been confirmed that the proposed interfaces could make the surgical robot system more efficiently by overcoming its several limitations.1. Introduction 1 1.1. Robotic Laparoscopic Surgery 1 1.2. Objectives and Scope 8 1.2.1. Additional Master Interfaces 14 1.2.2. Application Systems 15 2. Materials and Methods 20 2.1. Additional Master Interfaces 20 2.1.1. Novel Master Interface: 9-way Compact Hands-On-Throttle-And-Stick 20 2.1.2. improved Novel Master Interface: Capacitive Touch Type Compact Hands-On-Throttle-And-Stick 26 2.2. Application Systems 34 2.2.1. Robotic Assistant 34 2.2.2. Stereo Endoscope System 49 3. Results 57 3.1. Novel Master Interface with Application Systems 57 3.1.1. Novel Master Interface 57 3.1.2. Robotic Assistant 59 3.1.3. Novel Master Interface with Robotic Assistant 67 3.1.4. Stereo Endoscope System 76 3.1.5. Novel Master Interface with Stereo Endoscope System 82 3.2. improved Novel Master Interface with Application Systems 87 3.2.1. improved Novel Master Interface 87 3.2.2. improved Novel Master Interface with Stereo Endoscope System 90 4. Discussion 91 5. Conclusion 102 References 105 Abstract in Korean 117Docto

The Next-Generation Surgical Robots

The chronicle of surgical robots is short but remarkable. Within 20 years since the regulatory approval of the first surgical robot, more than 3,000 units were installed worldwide, and more than half a million robotic surgical procedures were carried out in the past year alone. The exceptionally high speeds of market penetration and expansion to new surgical areas had raised technical, clinical, and ethical concerns. However, from a technological perspective, surgical robots today are far from perfect, with a list of improvements expected for the next-generation systems. On the other hand, robotic technologies are flourishing at ever-faster paces. Without the inherent conservation and safety requirements in medicine, general robotic research could be substantially more agile and explorative. As a result, various technical innovations in robotics developed in recent years could potentially be grafted into surgical applications and ignite the next major advancement in robotic surgery. In this article, the current generation of surgical robots is reviewed from a technological point of view, including three of possibly the most debated technical topics in surgical robotics: vision, haptics, and accessibility. Further to that, several emerging robotic technologies are highlighted for their potential applications in next-generation robotic surgery

Intraoperative robotic-assisted large-area high-speed microscopic imaging and intervention

Objective: Probe-based confocal endomicroscopy is an emerging high-magnification optical imaging technique that provides in-vivo and in-situ cellular-level imaging for real-time assessment of tissue pathology. Endomicroscopy could potentially be used for intraoperative surgical guidance, but it is challenging to assess a surgical site using individual microscopic images due to the limited field-of-view and difficulties associated with manually manipulating the probe. Methods: In this paper, a novel robotic device for large-area endomicroscopy imaging is proposed, demonstrating a rapid, but highly accurate, scanning mechanism with image-based motion control which is able to generate histology-like endomicroscopy mosaics. The device also includes, for the first time in robotic-assisted endomicroscopy, the capability to ablate tissue without the need for an additional tool. Results: The device achieves pre-programmed trajectories with positioning accuracy of less than 30um, the image-based approach demonstrated that it can suppress random motion disturbances up to 1.25mm/s. Mosaics are presented from a range of ex-vivo human and animal tissues, over areas of more than 3mm², scanned in approximate 10s. Conclusion: This work demonstrates the potential of the proposed instrument to generate large-area, high-resolution microscopic images for intraoperative tissue identification and margin assessment. Significance: This approach presents an important alternative to current histology techniques, significantly reducing the tissue assessment time, while simultaneously providing the capability to mark and ablate suspicious areas intraoperatively