Virtual Model Building for Multi-Axis Machine Tools Using Field Data

Accurate machine dynamic models are the foundation of many advanced machining technologies such as virtual process planning and machine condition monitoring. Viewing recent designs of modern high-performance machine tools, to enhance the machine versatility and productivity, the machine axis configuration is becoming more complex and diversified, and direct drive motors are more commonly used. Due to the above trends, coupled and nonlinear multibody dynamics in machine tools are gaining more attention. Also, vibration due to limited structural rigidity is an important issue that must be considered simultaneously. Hence, this research aims at building high-fidelity machine dynamic models that are capable of predicting the dynamic responses, such as the tracking error and motor current signals, considering a wide range of dynamic effects such as structural flexibility, inter-axis coupling, and posture-dependency. Building machine dynamic models via conventional bottom-up approaches may require extensive investigation on every single component. Such approaches are time-consuming or sometimes infeasible for the machine end-users. Alternatively, as the recent trend of Industry 4.0, utilizing data via Computer Numerical Controls (CNCs) and/or non-intrusive sensors to build the machine model is rather favorable for industrial implementation. Thus, the methods proposed in this thesis are top-down model building approaches, utilizing available data from CNCs and/or other auxiliary sensors. The achieved contributions and results of this thesis are summarized below. As the first contribution, a new modeling and identification technique targeting a closed-loop control system of coupled rigid multi-axis feed drives has been developed. A multi-axis closed-loop control system, including the controller and the electromechanical plant, is described by a multiple-input multiple-output (MIMO) linear time-invariant (LTI) system, coupled with a generalized disturbance input that represents all the nonlinear dynamics. Then, the parameters of the open-loop and closed-loop dynamic models are respectively identified by a strategy that combines linear Least Squares (LS) and constrained global optimization. This strategy strikes a balance between model accuracy and computational efficiency. This proposed method was validated using an industrial 5-axis laser drilling machine and an experimental feed drive, achieving 2.38% and 5.26% root mean square (RMS) prediction error, respectively. Inter-axis coupling effects, i.e., the motion of one axis causing the dynamic responses of another axis, are correctly predicted. Also, the tracking error induced by motor ripple and nonlinear friction is correctly predicted as well. As the second contribution, the above proposed methodology is extended to also consider structural flexibility, which is a crucial behavior of large-sized industrial 5-axis machine tools. More importantly, structural vibration is nonlinear and posture-dependent due to the nature of a multibody system. In this thesis, prominent cases of flexibility-induced vibrations in a linear feed drive are studied and modeled by lumped mass-spring-damper system. Then, a flexible linear drive coupled with a rotary drive is systematically analyzed. It is found that the case with internal structural vibration between the linear and rotary drives requires an additional motion sensor for the proposed model identification method. This particular case is studied with an experimental setup. The thesis presents a method to reconstruct such missing internal structural vibration using the data from the embedded encoders as well as a low-cost micro-electromechanical system (MEMS) inertial measurement unit (IMU) mounted on the machine table. It is achieved by first synchronizing the data, aligning inertial frames, and calibrating mounting misalignments. Finally, the unknown internal vibration is reconstructed by comparing the rigid and flexible machine kinematic models. Due to the measurement limitation of MEMS IMUs and geometric assembly error, the reconstructed angle is unfortunately inaccurate. Nevertheless, the vibratory angular velocity and acceleration are consistently reconstructed, which is sufficient for the identification with reasonable model simplification. Finally, the reconstructed internal vibration along with the gathered servo data are used to identify the proposed machine dynamic model. Due to the separation of linear and nonlinear dynamics, the vibratory dynamics can be simply considered by adding complex pole pairs into the MIMO LTI system. Experimental validation shows that the identified model is able to predict the dynamic responses of the tracking error and motor force/torque to the input command trajectory and external disturbances, with 2% ~ 6% RMS error. Especially, the vibratory inter-axis coupling effect and posture-dependent effect are accurately depicted. Overall, this thesis presents a dynamic model-building approach for multi-axis feed drive assemblies. The proposed model is general and can be configured according to the kinematic configuration. The model-building approach only requires the data from the servo system or auxiliary motion sensors, e.g., an IMU, which is non-intrusive and in favor of industrial implementation. Future research includes further investigation of the IMU measurement, geometric error identification, validation using more complicated feed drive system, and applications to the planning and monitoring of 5-axis machining process

Challenges of continuum robots in clinical context: a review

With the maturity of surgical robotic systems based on traditional rigid-link principles, the rate of progress slowed as limits of size and controllable degrees of freedom were reached. Continuum robots came with the potential to deliver a step change in the next generation of medical devices, by providing better access, safer interactions and making new procedures possible. Over the last few years, several continuum robotic systems have been launched commercially and have been increasingly adopted in hospitals. Despite the clear progress achieved, continuum robots still suffer from design complexity hindering their dexterity and scalability. Recent advances in actuation methods have looked to address this issue, offering alternatives to commonly employed approaches. Additionally, continuum structures introduce significant complexity in modelling, sensing, control and fabrication; topics which are of particular focus in the robotics community. It is, therefore, the aim of the presented work to highlight the pertinent areas of active research and to discuss the challenges to be addressed before the potential of continuum robots as medical devices may be fully realised

On Increasing the Automation Level of Heavy-Duty Hydraulic Manipulators with Condition Monitoring of the Hydraulic System and Energy-Optimised Redundancy Resolution

Hydraulic manipulators on mobile machines are predominantly used for excavation and lifting applications at construction sites and for heavy-duty material handling in the forest industry due to their superior power-density and rugged nature. These manipulators are conventionally open-loop controlled by human operators who are sufficiently skilled to operate the machines. However, in the footsteps of pioneering original equipment manufacturers (OEMs) and to keep up with the intensifying demand for innovation, more and more mobile machine OEMs have a major interest in significantly increasing the automation level of their hydraulic manipulators and improving the operation of manipulators. In this thesis, robotic software-based functionalities in the form of modelbased condition monitoring and energy-optimal redundancy resolution which facilitate increased automation level of hydraulic manipulators are proposed.A condition monitoring system generally consists of software modules and sensors which co-operate harmonically and monitor the hydraulic system’s health in real-time based on an indirect measure of this system’s health. The premise is that when this condition monitoring system recognises that the system’s health has deteriorated past a given threshold (in other words, when a minor fault is detected, such as a slowly increasing internal leakage of the hydraulic cylinder), the condition monitoring module issues an alarm to warn the system operator of the malfunction, and the module could ideally diagnose the fault cause. In addition, when faced with severe faults, such as an external leakage or an abruptly increasing internal leakage in the hydraulic system, an alarm from the condition monitoring system ensures that the machine is quickly halted to prevent any further damage to the machine or its surroundings.The basic requirement in the design of such a condition monitoring system is to make sure that this system is robust and fault-sensitive. These properties are difficult to achieve in complex mobile hydraulic systems on hydraulic manipulators due to the modelling uncertainties affecting these systems. The modelling uncertainties affecting mobile hydraulic systems are specific compared with many other types of systems and are large because of the hydraulic system complexities, nonlinearities, discontinuities and inherently time-varying parameters. A feasible solution to this modelling uncertainty problem would be to either attenuate the effect of modelling errors on the performance of model-based condition monitoring or to develop improved non-model-based methods with increased fault-sensitivity. In this research work, the former model-based approach is taken. Adaptation of the model residual thresholds based on system operating points and reliable, load-independent system models are proposed as integral parts of the condition monitoring solution to the modelling uncertainty problem. These proposed solutions make the realisation of condition monitoring solutions more difficult on heavy-duty hydraulic manipulators compared with fixed-load manipulators, for example. These solutions are covered in detail in a subset of the research publications appended to this thesis.There is wide-spread interest from hydraulic manipulator OEMs in increasing the automation level of their hydraulic manipulators. Most often, this interest is related to semi-automation of repetitive work cycles to improve work productivity and operator workload circumstances. This robotic semi-automated approach involves resolving the kinematic redundancy of hydraulic manipulators to obtain motion references for the joint controller to enable desirable closed-loop controlled motions. Because conventional redundancy resolutions are usually sub-optimal at the hydraulic system level, a hydraulic energy-optimised, global redundancy resolution is proposed in this thesis for the first time. Kinematic redundancy is resolved energy optimally from the standpoint of the hydraulic system along a prescribed path for a typical 3-degrees-of-freedom (3-DOF) and 4-DOF hydraulic manipulator. Joint motions are also constrained based on the actuators’ position, velocity and acceleration bounds in hydraulic manipulators in the proposed solution. This kinematic redundancy resolution topic is discussed in the last two research papers. Overall, both designed manipulator features, condition monitoring and energy-optimised redundancy resolution, are believed to be essential for increasing the automation of hydraulic manipulators

Robotic manipulators for single access surgery

This thesis explores the development of cooperative robotic manipulators for enhancing surgical precision and patient outcomes in single-access surgery and, specifically, Transanal Endoscopic Microsurgery (TEM). During these procedures, surgeons manipulate a heavy set of instruments via a mechanical clamp inserted in the patient’s body through a surgical port, resulting in imprecise movements, increased patient risks, and increased operating time. Therefore, an articulated robotic manipulator with passive joints is initially introduced, featuring built-in position and force sensors in each joint and electronic joint brakes for instant lock/release capability. The articulated manipulator concept is further improved with motorised joints, evolving into an active tool holder. The joints allow the incorporation of advanced robotic capabilities such as ultra-lightweight gravity compensation and hands-on kinematic reconfiguration, which can optimise the placement of the tool holder in the operating theatre. Due to the enhanced sensing capabilities, the application of the active robotic manipulator was further explored in conjunction with advanced image guidance approaches such as endomicroscopy. Recent advances in probe-based optical imaging such as confocal endomicroscopy is making inroads in clinical uses. However, the challenging manipulation of imaging probes hinders their practical adoption. Therefore, a combination of the fully cooperative robotic manipulator with a high-speed scanning endomicroscopy instrument is presented, simplifying the incorporation of optical biopsy techniques in routine surgical workflows. Finally, another embodiment of a cooperative robotic manipulator is presented as an input interface to control a highly-articulated robotic instrument for TEM. This master-slave interface alleviates the drawbacks of traditional master-slave devices, e.g., using clutching mechanics to compensate for the mismatch between slave and master workspaces, and the lack of intuitive manipulation feedback, e.g. joint limits, to the user. To address those drawbacks a joint-space robotic manipulator is proposed emulating the kinematic structure of the flexible robotic instrument under control.Open Acces

Modeling, simulation and control of microrobots for the microfactory.

Future assembly technologies will involve higher levels of automation in order to satisfy increased microscale or nanoscale precision requirements. Traditionally, assembly using a top-down robotic approach has been well-studied and applied to the microelectronics and MEMS industries, but less so in nanotechnology. With the boom of nanotechnology since the 1990s, newly designed products with new materials, coatings, and nanoparticles are gradually entering everyone’s lives, while the industry has grown into a billion-dollar volume worldwide. Traditionally, nanotechnology products are assembled using bottom-up methods, such as self-assembly, rather than top-down robotic assembly. This is due to considerations of volume handling of large quantities of components, and the high cost associated with top-down manipulation requiring precision. However, bottom-up manufacturing methods have certain limitations, such as components needing to have predefined shapes and surface coatings, and the number of assembly components being limited to very few. For example, in the case of self-assembly of nano-cubes with an origami design, post-assembly manipulation of cubes in large quantities and cost-efficiency is still challenging. In this thesis, we envision a new paradigm for nanoscale assembly, realized with the help of a wafer-scale microfactory containing large numbers of MEMS microrobots. These robots will work together to enhance the throughput of the factory, while their cost will be reduced when compared to conventional nanopositioners. To fulfill the microfactory vision, numerous challenges related to design, power, control, and nanoscale task completion by these microrobots must be overcome. In this work, we study two classes of microrobots for the microfactory: stationary microrobots and mobile microrobots. For the stationary microrobots in our microfactory application, we have designed and modeled two different types of microrobots, the AFAM (Articulated Four Axes Microrobot) and the SolarPede. The AFAM is a millimeter-size robotic arm working as a nanomanipulator for nanoparticles with four degrees of freedom, while the SolarPede is a light-powered centimeter-size robotic conveyor in the microfactory. For mobile microrobots, we have introduced the world’s first laser-driven micrometer-size locomotor in dry environments, called ChevBot to prove the concept of the motion mechanism. The ChevBot is fabricated using MEMS technology in the cleanroom, following a microassembly step. We showed that it can perform locomotion with pulsed laser energy on a dry surface. Based on the knowledge gained with the ChevBot, we refined tits fabrication process to remove the assembly step and increase its reliability. We designed and fabricated a steerable microrobot, the SerpenBot, in order to achieve controllable behavior with the guidance of a laser beam. Through modeling and experimental study of the characteristics of this type of microrobot, we proposed and validated a new type of deep learning controller, the PID-Bayes neural network controller. The experiments showed that the SerpenBot can achieve closed-loop autonomous operation on a dry substrate