A dynamic two-dimensional (D2D) weight-based map-matching algorithm

Existing map-Matching (MM) algorithms primarily localize positioning fixes along the centerline of a road and have largely ignored road width as an input. Consequently, vehicle lane-level localization, which is essential for stringent Intelligent Transport System (ITS) applications, seems difficult to accomplish, especially with the positioning data from low-cost GPS sensors. This paper aims to address this limitation by developing a new dynamic two-dimensional (D2D) weight-based MM algorithm incorporating dynamic weight coefficients and road width. To enable vehicle lane-level localization, a road segment is virtually expressed as a matrix of homogeneous grids with reference to a road centerline. These grids are then used to map-match positioning fixes as opposed to matching on a road centerline as carried out in traditional MM algorithms. In this developed algorithm, vehicle location identification on a road segment is based on the total weight score which is a function of four different weights: (i) proximity, (ii) kinematic, (iii) turn-intent prediction, and (iv) connectivity. Different parameters representing network complexity and positioning quality are used to assign the relative importance to different weight scores by employing an adaptive regression method. To demonstrate the transferability of the developed algorithm, it was tested by using 5,830 GPS positioning points collected in Nottingham, UK and 7,414 GPS positioning points collected in Mumbai and Pune, India. The developed algorithm, using stand-alone GPS position fixes, identifies the correct links 96.1% (for the Nottingham data) and 98.4% (for the Mumbai-Pune data) of the time. In terms of the correct lane identification, the algorithm was found to provide the accurate matching for 84% (Nottingham) and 79% (Mumbai-Pune) of the fixes obtained by stand-alone GPS. Using the same methodology adopted in this study, the accuracy of the lane identification could further be enhanced if the localization data from additional sensors (e.g. gyroscope) are utilized. ITS industry and vehicle manufacturers can implement this D2D map-matching algorithm for liability critical and in-vehicle information systems and services such as advanced driver assistant systems (ADAS)

Vision-Based Georeferencing of GPR in Urban Areas

Ground Penetrating Radar (GPR) surveying is widely used to gather accurate knowledge about the geometry and position of underground utilities. The sensor arrays need to be coupled to an accurate positioning system, like a geodetic-grade Global Navigation Satellite System (GNSS) device. However, in urban areas this approach is not always feasible because GNSS accuracy can be substantially degraded due to the presence of buildings, trees, tunnels, etc. In this work, a photogrammetric (vision-based) method for GPR georeferencing is presented. The method can be summarized in three main steps: tie point extraction from the images acquired during the survey, computation of approximate camera extrinsic parameters and finally a refinement of the parameter estimation using a rigorous implementation of the collinearity equations. A test under operational conditions is described, where accuracy of a few centimeters has been achieved. The results demonstrate that the solution was robust enough for recovering vehicle trajectories even in critical situations, such as poorly textured framed surfaces, short baselines, and low intersection angles

Infrastructure Wi-Fi for connected autonomous vehicle positioning : a review of the state-of-the-art

In order to realize intelligent vehicular transport networks and self driving cars, connected autonomous vehicles (CAVs) are required to be able to estimate their position to the nearest centimeter. Traditional positioning in CAVs is realized by using a global navigation satellite system (GNSS) such as global positioning system (GPS) or by fusing weighted location parameters from a GNSS with an inertial navigation systems (INSs). In urban environments where Wi-Fi coverage is ubiquitous and GNSS signals experience signal blockage, multipath or non line-of-sight (NLOS) propagation, enterprise or carrier-grade Wi-Fi networks can be opportunistically used for localization or “fused” with GNSS to improve the localization accuracy and precision. While GNSS-free localization systems are in the literature, a survey of vehicle localization from the perspective of a Wi-Fi anchor/infrastructure is limited. Consequently, this review seeks to investigate recent technological advances relating to positioning techniques between an ego vehicle and a vehicular network infrastructure. Also discussed in this paper is an analysis of the location accuracy, complexity and applicability of surveyed literature with respect to intelligent transportation system requirements for CAVs. It is envisaged that hybrid vehicular localization systems will enable pervasive localization services for CAVs as they travel through urban canyons, dense foliage or multi-story car parks

Survey on Recent Advances in Integrated GNSSs Towards Seamless Navigation Using Multi-Sensor Fusion Technology

During the past few decades, the presence of global navigation satellite systems (GNSSs) such as GPS, GLONASS, Beidou and Galileo has facilitated positioning, navigation and timing (PNT) for various outdoor applications. With the rapid increase in the number of orbiting satellites per GNSS, enhancements in the satellite-based augmentation systems (SBASs) such as EGNOS and WAAS, as well as commissioning new GNSS constellations, the PNT capabilities are maximized to reach new frontiers. Additionally, the recent developments in precise point positioning (PPP) and real time kinematic (RTK) algorithms have provided more feasibility to carrier-phase precision positioning solutions up to the third-dimensional localization. With the rapid growth of internet of things (IoT) applications, seamless navigation becomes very crucial for numerous PNT dependent applications especially in sensitive fields such as safety and industrial applications. Throughout the years, GNSSs have maintained sufficiently acceptable performance in PNT, in RTK and PPP applications however GNSS experienced major challenges in some complicated signal environments. In many scenarios, GNSS signal suffers deterioration due to multipath fading and attenuation in densely obscured environments that comprise stout obstructions. Recently, there has been a growing demand e.g. in the autonomous-things domain in adopting reliable systems that accurately estimate position, velocity and time (PVT) observables. Such demand in many applications also facilitates the retrieval of information about the six degrees of freedom (6-DOF - x, y, z, roll, pitch, and heading) movements of the target anchors. Numerous modern applications are regarded as beneficiaries of precise PNT solutions such as the unmanned aerial vehicles (UAV), the automatic guided vehicles (AGV) and the intelligent transportation system (ITS). Hence, multi-sensor fusion technology has become very vital in seamless navigation systems owing to its complementary capabilities to GNSSs. Fusion-based positioning in multi-sensor technology comprises the use of multiple sensors measurements for further refinement in addition to the primary GNSS, which results in high precision and less erroneous localization. Inertial navigation systems (INSs) and their inertial measurement units (IMUs) are the most commonly used technologies for augmenting GNSS in multi-sensor integrated systems. In this article, we survey the most recent literature on multi-sensor GNSS technology for seamless navigation. We provide an overall perspective for the advantages, the challenges and the recent developments of the fusion-based GNSS navigation realm as well as analyze the gap between scientific advances and commercial offerings. INS/GNSS and IMU/GNSS systems have proven to be very reliable in GNSS-denied environments where satellite signal degradation is at its peak, that is why both integrated systems are very abundant in the relevant literature. In addition, the light detection and ranging (LiDAR) systems are widely adopted in the literature for its capability to provide 6-DOF to mobile vehicles and autonomous robots. LiDARs are very accurate systems however they are not suitable for low-cost positioning due to the expensive initial costs. Moreover, several other techniques from the radio frequency (RF) spectrum are utilized as multi-sensor systems such as cellular networks, WiFi, ultra-wideband (UWB) and Bluetooth. The cellular-based systems are very suitable for outdoor navigation applications while WiFi-based, UWB-based and Bluetooth-based systems are efficient in indoor positioning systems (IPS). However, to achieve reliable PVT estimations in multi-sensor GNSS navigation, optimal algorithms should be developed to mitigate the estimation errors resulting from non-line-of-sight (NLOS) GNSS situations. Examples of the most commonly used algorithms for trilateration-based positioning are Kalman filters, weighted least square (WLS), particle filters (PF) and many other hybrid algorithms by mixing one or more algorithms together. In this paper, the reviewed articles under study and comparison are presented by highlighting their motivation, the methodology of implementation, the modelling utilized and the performed experiments. Then they are assessed with respect to the published results focusing on achieved accuracy, robustness and overall implementation cost-benefits as performance metrics. Our summarizing survey assesses the most promising, highly ranked and recent articles that comprise insights into the future of GNSS technology with multi-sensor fusion technique.©2021 The Authors. Published by ION.fi=vertaisarvioimaton|en=nonPeerReviewed

The simultaneous localization and mapping (SLAM):An overview

Positioning is a need for many applications related to mapping and navigation either in civilian or military domains. The significant developments in satellite-based techniques, sensors, telecommunications, computer hardware and software, image processing, etc. positively influenced to solve the positioning problem efficiently and instantaneously. Accordingly, the mentioned development empowered the applications and advancement of autonomous navigation. One of the most interesting developed positioning techniques is what is called in robotics as the Simultaneous Localization and Mapping SLAM. The SLAM problem solution has witnessed a quick improvement in the last decades either using active sensors like the RAdio Detection And Ranging (Radar) and Light Detection and Ranging (LiDAR) or passive sensors like cameras. Definitely, positioning and mapping is one of the main tasks for Geomatics engineers, and therefore it's of high importance for them to understand the SLAM topic which is not easy because of the huge documentation and algorithms available and the various SLAM solutions in terms of the mathematical models, complexity, the sensors used, and the type of applications. In this paper, a clear and simplified explanation is introduced about SLAM from a Geomatical viewpoint avoiding going into the complicated algorithmic details behind the presented techniques. In this way, a general overview of SLAM is presented showing the relationship between its different components and stages like the core part of the front-end and back-end and their relation to the SLAM paradigm. Furthermore, we explain the major mathematical techniques of filtering and pose graph optimization either using visual or LiDAR SLAM and introduce a summary of the deep learning efficient contribution to the SLAM problem. Finally, we address examples of some existing practical applications of SLAM in our reality