Review on suitable eDRAM configurations for next nano-metric electronics era

We summarize most of our studies focused on the main reliability issues that can threat the gain-cells eDRAM behavior when it is simulated at the nano-metric device range has been collected in this review. So, to outperform their memory cell counterparts, we explored different technological proposals and operational regimes where it can be located. The best memory cell performance is observed for the 3T1D-eDRAM cell when it is based on FinFET devices. Both device variability and SEU appear as key reliability issues for memory cells at sub-22nm technology node.Peer ReviewedPostprint (author's final draft

Cache memory design in the FinFET era

The major problem in the future technology scaling is the variations in process parameters that are interpreted as imperfections in the development process. Moreover, devices are more sensitive to the environmental changes of temperature and supply volt- age as well as to ageing. All these influences are manifested in the integrated circuits as increased power consumption, reduced maximal operating frequency and increased number of failures. These effects have been partially overcome with the introduction of the FinFET technology which have solved the problem of variability caused by Random Dopant Fluctuations. However, in the next ten years channel length is projected to shrink to 10nm where the variability source generated by Line Edge Roughness will dominate, and its effects on the threshold voltage variations will become critical. The embedded memories with their cells as the basic building unit are the most prone to these effects due to their the smallest dimensions. Because of that, memories should be designed with particular care in order to make possible further technology scaling. This thesis explores upcoming 10nm FinFETs and the existing issues in the cache memory design with this technology. More- over, it tries to present some original and novel techniques on the different level of design abstraction for mitigating the effects of process and environmental variability. At first original method for simulating variability of Tri-Gate Fin- FETs is presented using conventional HSPICE simulation environment and BSIM-CMG model cards. When that is accomplished, thorough characterisation of traditional SRAM cell circuits (6T and 8T) is performed. Possibility of using Independent Gate FinFETs for increasing cell stability has been explored, also. Gain Cells appeared in the recent past as an attractive alternative for in the cache memory design. This thesis partially explores this idea by presenting and performing detailed circuit analysis of the dynamic 3T gain cell for 10nm FinFETs. At the top of this work, thesis shows one micro-architecture optimisation of high-speed cache when it is implemented by 3T gain cells. We show how the cache coherency states can be used in order to reduce refresh energy of the memory as well as reduce memory ageing.El principal problema de l'escalat la tecnologia són les variacions en els paràmetres de disseny (imperfeccions) durant procés de fabricació. D'altra banda, els dispositius també són més sensibles als canvis ambientals de temperatura, la tensió d'alimentació, així com l'envelliment. Totes aquestes influències es manifesten en els circuits integrats com l'augment de consum d'energia, la reducció de la freqüència d'operació màxima i l'augment del nombre de xips descartats. Aquests efectes s'han superat parcialment amb la introducció de la tecnologia FinFET que ha resolt el problema de la variabilitat causada per les fluctuacions de dopants aleatòries. No obstant això, en els propers deu anys, l'ample del canal es preveu que es reduirà a 10nm, on la font de la variabilitat generada per les rugositats de les línies de material dominarà, i els seu efecte en les variacions de voltatge llindar augmentarà. Les memòries encastades amb les seves cel·les com la unitat bàsica de construcció són les més propenses a sofrir aquests efectes a causa de les seves dimensions més petites. A causa d'això, cal dissenyar les memòries amb una especial cura per tal de fer possible l'escalat de la tecnologia. Aquesta tesi explora la tecnologia de FinFETs de 10nm i els problemes existents en el disseny de memòries amb aquesta tecnologia. A més a més, presentem noves tècniques originals sobre diferents nivells d'abstracció del disseny per a la mitigació dels efectes les variacions tan de procés com ambientals. En primer lloc, presentem un mètode original per a la simulació de la variabilitat de Tri-Gate FinFETs usant entorn de simulació HSPICE convencional i models de tecnologia BSIMCMG. Després, es realitza la caracterització completa dels circuits de cel·les SRAM tradicionals (6T i 8T) conjuntament amb l'ús de Gate-independent FinFETs per augmentar l'estabilitat de la cèl·lula

Reliability-aware memory design using advanced reconfiguration mechanisms

Fast and Complex Data Memory systems has become a necessity in modern computational units in today's integrated circuits. These memory systems are integrated in form of large embedded memory for data manipulation and storage. This goal has been achieved by the aggressive scaling of transistor dimensions to few nanometer (nm) sizes, though; such a progress comes with a drawback, making it critical to obtain high yields of the chips. Process variability, due to manufacturing imperfections, along with temporal aging, mainly induced by higher electric fields and temperature, are two of the more significant threats that can no longer be ignored in nano-scale embedded memory circuits, and can have high impact on their robustness. Static Random Access Memory (SRAM) is one of the most used embedded memories; generally implemented with the smallest device dimensions and therefore its robustness can be highly important in nanometer domain design paradigm. Their reliable operation needs to be considered and achieved both in cell and also in architectural SRAM array design. Recently, and with the approach to near/below 10nm design generations, novel non-FET devices such as Memristors are attracting high attention as a possible candidate to replace the conventional memory technologies. In spite of their favorable characteristics such as being low power and highly scalable, they also suffer with reliability challenges, such as process variability and endurance degradation, which needs to be mitigated at device and architectural level. This thesis work tackles such problem of reliability concerns in memories by utilizing advanced reconfiguration techniques. In both SRAM arrays and Memristive crossbar memories novel reconfiguration strategies are considered and analyzed, which can extend the memory lifetime. These techniques include monitoring circuits to check the reliability status of the memory units, and architectural implementations in order to reconfigure the memory system to a more reliable configuration before a fail happens.Actualmente, el diseño de sistemas de memoria en circuitos integrados busca continuamente que sean más rápidos y complejos, lo cual se ha vuelto de gran necesidad para las unidades de computación modernas. Estos sistemas de memoria están integrados en forma de memoria embebida para una mejor manipulación de los datos y de su almacenamiento. Dicho objetivo ha sido conseguido gracias al agresivo escalado de las dimensiones del transistor, el cual está llegando a las dimensiones nanométricas. Ahora bien, tal progreso ha conllevado el inconveniente de una menor fiabilidad, dado que ha sido altamente difícil obtener elevados rendimientos de los chips. La variabilidad de proceso - debido a las imperfecciones de fabricación - junto con la degradación de los dispositivos - principalmente inducido por el elevado campo eléctrico y altas temperaturas - son dos de las más relevantes amenazas que no pueden ni deben ser ignoradas por más tiempo en los circuitos embebidos de memoria, echo que puede tener un elevado impacto en su robusteza final. Static Random Access Memory (SRAM) es una de las celdas de memoria más utilizadas en la actualidad. Generalmente, estas celdas son implementadas con las menores dimensiones de dispositivos, lo que conlleva que el estudio de su robusteza es de gran relevancia en el actual paradigma de diseño en el rango nanométrico. La fiabilidad de sus operaciones necesita ser considerada y conseguida tanto a nivel de celda de memoria como en el diseño de arquitecturas complejas basadas en celdas de memoria SRAM. Actualmente, con el diseño de sistemas basados en dispositivos de 10nm, dispositivos nuevos no-FET tales como los memristores están atrayendo una elevada atención como posibles candidatos para reemplazar las actuales tecnologías de memorias convencionales. A pesar de sus características favorables, tales como el bajo consumo como la alta escabilidad, ellos también padecen de relevantes retos de fiabilidad, como son la variabilidad de proceso y la degradación de la resistencia, la cual necesita ser mitigada tanto a nivel de dispositivo como a nivel arquitectural. Con todo esto, esta tesis doctoral afronta tales problemas de fiabilidad en memorias mediante la utilización de técnicas de reconfiguración avanzada. La consideración de nuevas estrategias de reconfiguración han resultado ser validas tanto para las memorias basadas en celdas SRAM como en `memristive crossbar¿, donde se ha observado una mejora significativa del tiempo de vida en ambos casos. Estas técnicas incluyen circuitos de monitorización para comprobar la fiabilidad de las unidades de memoria, y la implementación arquitectural con el objetivo de reconfigurar los sistemas de memoria hacia una configuración mucho más fiables antes de que el fallo suced

Technology Implications for Large Last-Level Caches

Large last-level cache (L3C) is efficient for bridging the performance and power gap between processor and memory. Several memory technologies, including SRAM, STT-RAM (MRAM), and embedded DRAM (eDRAM), have been used or considered as the technology to implement L3Cs. However, each of them has inherent weaknesses: SRAM is relatively low density and dissipates high leakage; STT-RAM has long write latency and requires high write energy; eDRAM requires refresh. As future processors are expected to have larger last-level caches, the objective of this dissertation is to study the tradeoffs associated with using each of these technologies to implement L3Cs. In order to make useful comparisons between L3Cs built with SRAM, STT-RAM, and eDRAM, we consider and implement several levels of details. First, to obtain unbiased cache performance and power properties (i.e., read/write access latency, read/write access energy, leakage power, refresh power, area), we prototype caches based on realistic memory and device models. Second, we present simplistic analytical models that enable us to quickly examine different memory technologies under various scenarios. Third, we review power-optimization techniques for each of the technologies, and propose using a low-cost dead-line prediction scheme for eDRAM-based L3Cs to eliminate unnecessary refreshes. Finally, the highlight of this dissertation is the comparison and analysis of low-leakage SRAM, low write-energy STT-RAM, and refresh-optimized eDRAM. We report system performance, last-level cache energy breakdown, and memory hierarchy energy breakdown, using an augmented full-system simulator with the execution of a range of workloads and input sets. From the insights gained through simulation results, STT-RAM has the highest potential to save energy in future L3C designs. For contemporary processors, SRAM-based L3C results in the fastest system performance, whereas eDRAM consumes the lowest energy