182 research outputs found
To Achieve Security and High Spectrum Efficiency: A New Transmission System Based on Faster-than-Nyquist and Deep Learning
With the rapid development of various services in wireless communications,
spectrum resource has become increasingly valuable. Faster-than-Nyquist (FTN)
signaling, which was proposed in the 1970s, has been a promising paradigm to
improve the spectrum utilization. In this paper, we try to apply FTN into
secure communications and propose a secure and high-spectrum-efficiency
transmission system based on FTN and deep learning (DL). In the proposed
system, the hopping symbol packing ratio with random values makes it difficult
for the eavesdropper to obtain the accurate symbol rate and inter-symbol
interference (ISI). While the receiver can use the blind estimation to choose
the true parameters with the aid of DL. The results show that without the
accurate symbol packing ratio, the eavesdropper will suffer from severe
performance degradation. As a result, the system can achieve a secure
transmission with a higher spectrum efficiency. Also, we propose a simplified
symbol packing ratio estimation which has bee employed in our proposed system.
Results show that the proposed simplified estimation achieves nearly the same
performance as the original structure while its complexity has been greatly
reduced
Waveform-Defined Security Enhancement via Signal Generation optimization
Traditional defence strategies of physical layer security (PLS) are highly dependent on channel environments. This work investigates a waveform-defined security (WDS) framework, which can fundamentally prevent signal interception. In the traditional WDS framework, by intentionally tuning waveform parameters to weaken feature diversity and enhance feature similarity, eavesdroppers cannot correctly identify feature-similarity dominant signals using deep learning (DL) classifiers. The imperfect signal classification would result in subsequent detection errors. This work aims to optimize the framework by further complicating signal classification using a newly proposed signal generation architecture. Results show that the new signal generator can cut distinguishable signal features. In this case, classification accuracy at eavesdroppers is reduced by up to 53% leading to an enhanced WDS framework. Meanwhile, legitimate users maintain performance reliability regardless of signal generation architectures
Optimal Pilot Sequences for Phase and Timing Synchronization in FTN Systems
In this paper, we study the joint phase and timing estimation problem in Faster-than-Nyquist (FTN) systems. We use the Cramér-Rao lower bound (CRB) as a cost function to design optimal pilot sequences subject to an energy constraint. We rely on harmonic approximations of the bound to establish closed-form relations between the ultimate synchronization performance and the transmitted waveform characteristics (i.e., pulse shaping filter and signaling density). We show that increasing the symbol rate at fixed bandwidth is beneficial to phase estimation and detrimental to timing synchronization. Therefore, we propose a joint timing/phase pilot design to accommodate this trade-off. Lastly, we illustrate the strengths of the proposed pilots with respect to traditional Zadoff-Chu sequences in presence of a residual carrier frequency offset
Ultra-Wideband Secure Communications and Direct RF Sampling Transceivers
Larger wireless device bandwidth results in new capabilities in terms of higher data rates and security. The 5G evolution is focus on exploiting larger bandwidths for higher though-puts. Interference and co-existence issues can also be addressed by the larger bandwidth in the 5G and 6G evolution. This dissertation introduces of a novel Ultra-wideband (UWB) Code Division Multiple Access (CDMA) technique to exploit the largest bandwidth available in the upcoming wireless connectivity scenarios. The dissertation addresses interference immunity, secure communication at the physical layer and longer distance communication due to increased receiver sensitivity. The dissertation presents the design, workflow, simulations, hardware prototypes and experimental measurements to demonstrate the benefits of wideband Code-Division-Multiple-Access. Specifically, a description of each of the hardware and software stages is presented along with simulations of different scenarios using a test-bench and open-field measurements. The measurements provided experimental validation carried out to demonstrate the interference mitigation capabilities. In addition, Direct RF sampling techniques are employed to handle the larger bandwidth and avoid analog components. Additionally, a transmit and receive chain is designed and implemented at 28 GHz to provide a proof-of-concept for future 5G applications. The proposed wideband transceiver is also used to demonstrate higher accuracy direction finding, as much as 10 times improvement
Ultra Wideband Communications: from Analog to Digital
Ultrabreitband-Signale (Ultra Wideband [UWB]) können einen
signifikanten Nutzen im Bereich drahtloser Kommunikationssysteme haben. Es
sind jedoch noch einige Probleme offen, die durch Systemdesigner und
Wissenschaftler gelöst werden müssen. Ein Funknetzsystem mit einer derart
groĂźen Bandbreite ist normalerweise auch durch eine groĂźe Anzahl an
Mehrwegekomponenten mit jeweils verschiedenen Pfadamplituden
gekennzeichnet. Daher ist es schwierig, die zeitlich verteilte Energie
effektiv zu erfassen. Außerdem ist in vielen Fällen der naheliegende
Ansatz, ein kohärenter Empfänger im Sinne eines signalangepassten Filters
oder eines Korrelators, nicht unbedingt die beste Wahl. In der vorliegenden
Arbeit wird dabei auf die bestehende Problematik und weitere
Lösungsmöglichkeiten eingegangen.
Im ersten Abschnitt geht es um „Impulse Radio UWB”-Systeme mit
niedriger Datenrate. Bei diesen Systemen kommt ein inkohärenter Empfänger
zum Einsatz. Inkohärente Signaldetektion stellt insofern einen
vielversprechenden Ansatz dar, als das damit aufwandsgĂĽnstige und robuste
Implementierungen möglich sind. Dies trifft vor allem in Anwendungsfällen
wie den von drahtlosen Sensornetzen zu, wo preiswerte Geräte mit langer
Batterielaufzeit nötigsind. Dies verringert den für die Kanalschätzung
und die Synchronisation nötigen Aufwand, was jedoch auf Kosten der
Leistungseffizienz geht und eine erhöhte Störempfindlichkeit gegenüber
Interferenz (z.B. Interferenz durch mehrere Nutzer oder schmalbandige
Interferenz) zur Folge hat.
Um die Bitfehlerrate der oben genannten Verfahren zu bestimmen, wurde
zunächst ein inkohärenter Combining-Verlust spezifiziert, welcher
auftritt im Gegensatz zu kohärenter Detektion mit Maximum Ratio Multipath
Combining. Dieser Verlust hängt von dem Produkt aus der Länge des
Integrationsfensters und der Signalbandbreite ab.
Um den Verlust durch inkohärentes Combining zu reduzieren und somit die
Leistungseffizienz des Empfängers zu steigern, werden verbesserte
Combining-Methoden fĂĽr Mehrwegeempfang vorgeschlagen. Ein analoger
Empfänger, bei dem der Hauptteil des Mehrwege-Combinings durch einen
„Integrate and Dump”-Filter implementiert ist, wird für UWB-Systeme
mit Zeit-Hopping gezeigt. Dabei wurde die Einsatzmöglichkeit von dünn
besetzten Codes in solchen System diskutiert und bewertet. Des Weiteren
wird eine Regel für die Code-Auswahl vorgestellt, welche die Stabilität
des Systems gegen Mehrnutzer-Störungen sicherstellt und gleichzeitig den
Verlust durch inkohärentes Combining verringert.
Danach liegt der Fokus auf digitalen Lösungen bei inkohärenter
Demodulation. Im Vergleich zum Analogempfänger besitzt ein
Digitalempfänger einen Analog-Digital-Wandler im Zeitbereich gefolgt von
einem digitalen Optimalfilter. Der digitale Optimalfilter dekodiert den
Mehrfachzugriffscode kohärent und beschränkt das inkohärente Combining
auf die empfangenen Mehrwegekomponenten im Digitalbereich. Es kommt ein
schneller Analog-Digital-Wandler mit geringer Auflösung zum Einsatz, um
einen vertretbaren Energieverbrauch zu gewährleisten. Diese Digitaltechnik
macht den Einsatz langer Analogverzögerungen bei differentieller
Demodulation unnötig und ermöglicht viele Arten der digitalen
Signalverarbeitung. Im Vergleich zur Analogtechnik reduziert sie nicht nur
den inkohärenten Combining-Verlust, sonder zeigt auch eine stärkere
Resistenz gegenüber Störungen. Dabei werden die Auswirkungen der
Auflösung und der Abtastrate der Analog-Digital-Umsetzung analysiert. Die
Resultate zeigen, dass die verminderte Effizienz solcher
Analog-Digital-Wandler gering ausfällt. Weiterhin zeigt sich, dass im
Falle starker Mehrnutzerinterferenz sogar eine Verbesserung der Ergebnisse
zu beobachten ist. Die vorgeschlagenen Design-Regeln spezifizieren die
Anwendung der Analog-Digital-Wandler und die Auswahl der Systemparameter in
Abhängigkeit der verwendeten Mehrfachzugriffscodes und der Modulationsart.
Wir zeigen, wie unter Anwendung erweiterter Modulationsverfahren die
Leistungseffizienz verbessert werden kann und schlagen ein Verfahren zur
Unterdrückung schmalbandiger Störer vor, welches auf Soft Limiting
aufbaut. Durch die Untersuchungen und Ergebnissen zeigt sich, dass
inkohärente Empfänger in UWB-Kommunikationssystemen mit niedriger
Datenrate ein groĂźes Potential aufweisen.
AuĂźerdem wird die Auswahl der benutzbaren Bandbreite untersucht, um einen
Kompromiss zwischen inkohärentem Combining-Verlust und Stabilität
gegenĂĽber langsamen Schwund zu erreichen. Dadurch wurde ein neues Konzept
für UWB-Systeme erarbeitet: wahlweise kohärente oder inkohärente
Empfänger, welche als UWB-Systeme Frequenz-Hopping nutzen. Der wesentliche
Vorteil hiervon liegt darin, dass die Bandbreite im Basisband sich deutlich
verringert. Mithin ermöglicht dies einfach zu realisierende digitale
Signalverarbeitungstechnik mit kostengĂĽnstigen Analog-Digital-Wandlern.
Dies stellt eine neue Epoche in der Forschung im Bereich drahtloser
Sensorfunknetze dar.
Der Schwerpunkt des zweiten Abschnitts stellt adaptiven Signalverarbeitung
für hohe Datenraten mit „Direct Sequence”-UWB-Systemen in den
Vordergrund. In solchen Systemen entstehen, wegen der groĂźen Anzahl der
empfangenen Mehrwegekomponenten, starke Inter- bzw.
Intrasymbolinterferenzen. Außerdem kann die Funktionalität des Systems
durch Mehrnutzerinterferenz und Schmalbandstörungen deutlich beeinflusst
werden. Um sie zu eliminieren, wird die „Widely Linear”-Rangreduzierung
benutzt. Dabei verbessert die Rangreduzierungsmethode das
Konvergenzverhalten, besonders wenn der gegebene Vektor eine sehr groĂźe
Anzahl an Abtastwerten beinhaltet (in Folge hoher einer Abtastrate).
Zusätzlich kann das System durch die Anwendung der R-linearen Verarbeitung
die Statistik zweiter Ordnung des nicht-zirkularen Signals vollständig
ausnutzen, was sich in verbesserten Schätzergebnissen widerspiegelt.
Allgemeine kann die Methode der „Widely Linear”-Rangreduzierung auch in
andern Bereichen angewendet werden, z.B. in „Direct
Sequence”-Codemultiplexverfahren (DS-CDMA), im MIMO-Bereich, im Global
System for Mobile Communications (GSM) und beim Beamforming.The aim of this thesis is to investigate key issues encountered in the
design of transmission schemes and receiving techniques for Ultra Wideband
(UWB) communication systems. Based on different data rate applications,
this work is divided into two parts, where energy efficient and robust
physical layer solutions are proposed, respectively.
Due to a huge bandwidth of UWB signals, a considerable amount of multipath
arrivals with various path gains is resolvable at the receiver. For low
data rate impulse radio UWB systems, suboptimal non-coherent detection is a
simple way to effectively capture the multipath energy. Feasible techniques
that increase the power efficiency and the interference robustness of
non-coherent detection need to be investigated. For high data rate direct
sequence UWB systems, a large number of multipath arrivals results in
severe inter-/intra-symbol interference. Additionally, the system
performance may also be deteriorated by multi-user interference and
narrowband interference. It is necessary to develop advanced signal
processing techniques at the receiver to suppress these interferences.
Part I of this thesis deals with the co-design of signaling schemes and
receiver architectures in low data rate impulse radio UWB systems based on
non-coherent detection.â—Ź We analyze the bit error rate performance of
non-coherent detection and characterize a non-coherent combining loss,
i.e., a performance penalty with respect to coherent detection with maximum
ratio multipath combining. The thorough analysis of this loss is very
helpful for the design of transmission schemes and receive techniques
innon-coherent UWB communication systems.â—Ź We propose to use optical
orthogonal codes in a time hopping impulse radio UWB system based on an
analog non-coherent receiver. The “analog” means that the major part of
the multipath combining is implemented by an integrate and dump filter. The
introduced semi-analytical method can help us to easily select the time
hopping codes to ensure the robustness against the multi-user interference
and meanwhile to alleviate the non-coherent combining loss.â—Ź The main
contribution of Part I is the proposal of applying fully digital solutions
in non-coherent detection. The proposed digital non-coherent receiver is
based on a time domain analog-to-digital converter, which has a high speed
but a very low resolution to maintain a reasonable power consumption.
Compared to its analog counterpart, itnot only significantly reduces the
non-coherent combining loss but also offers a higher interference
robustness. In particular, the one-bit receiver can effectively suppress
strong multi-user interference and is thus advantageous in separating
simultaneously operating piconets.The fully digital solutions overcome the
difficulty of implementing long analog delay lines and make differential
UWB detection possible. They also facilitate the development of various
digital signal processing techniques such as multi-user detection and
non-coherent multipath combining methods as well as the use of advanced
modulationschemes (e.g., M-ary Walsh modulation).â—Ź Furthermore, we
present a novel impulse radio UWB system based on frequency hopping, where
both coherent and non-coherent receivers can be adopted. The key advantage
is that the baseband bandwidth can be considerably reduced (e.g., lower
than 500 MHz), which enables low-complexity implementation of the fully
digital solutions. It opens up various research activities in the
application field of wireless sensor networks.
Part II of this thesis proposes adaptive widely linear reduced-rank
techniques to suppress interferences for high data rate direct sequence UWB
systems, where second-order non-circular signals are used. The reduced-rank
techniques are designed to improve the convergence performance and the
interference robustness especially when the received vector contains a
large number of samples (due to a high sampling rate in UWB systems). The
widely linear processing takes full advantage of the second-order
statistics of the non-circular signals and enhances the estimation
performance. The generic widely linear reduced-rank concept also has a
great potential in the applications of other systems such as Direct
Sequence Code Division Multiple Access (DS-CDMA), Multiple Input Multiple
Output (MIMO) system, and Global System for Mobile Communications (GSM), or
in other areas such as beamforming
Applications of satellite technology to broadband ISDN networks
Two satellite architectures for delivering broadband integrated services digital network (B-ISDN) service are evaluated. The first is assumed integral to an existing terrestrial network, and provides complementary services such as interconnects to remote nodes as well as high-rate multicast and broadcast service. The interconnects are at a 155 Mbs rate and are shown as being met with a nonregenerative multibeam satellite having 10-1.5 degree spots. The second satellite architecture focuses on providing private B-ISDN networks as well as acting as a gateway to the public network. This is conceived as being provided by a regenerative multibeam satellite with on-board ATM (asynchronous transfer mode) processing payload. With up to 800 Mbs offered, higher satellite EIRP is required. This is accomplished with 12-0.4 degree hopping beams, covering a total of 110 dwell positions. It is estimated the space segment capital cost for architecture one would be about 250M. The net user cost is given for a variety of scenarios, but the cost for 155 Mbs services is shown to be about $15-22/minute for 25 percent system utilization
A General Framework for Analyzing, Characterizing, and Implementing Spectrally Modulated, Spectrally Encoded Signals
Fourth generation (4G) communications will support many capabilities while providing universal, high speed access. One potential enabler for these capabilities is software defined radio (SDR). When controlled by cognitive radio (CR) principles, the required waveform diversity is achieved via a synergistic union called CR-based SDR. Research is rapidly progressing in SDR hardware and software venues, but current CR-based SDR research lacks the theoretical foundation and analytic framework to permit efficient implementation. This limitation is addressed here by introducing a general framework for analyzing, characterizing, and implementing spectrally modulated, spectrally encoded (SMSE) signals within CR-based SDR architectures. Given orthogonal frequency division multiplexing (OFDM) is a 4G candidate signal, OFDM-based signals are collectively classified as SMSE since modulation and encoding are spectrally applied. The proposed framework provides analytic commonality and unification of SMSE signals. Applicability is first shown for candidate 4G signals, and resultant analytic expressions agree with published results. Implementability is then demonstrated in multiple coexistence scenarios via modeling and simulation to reinforce practical utility
Enabling Technologies for Ultra-Reliable and Low Latency Communications: From PHY and MAC Layer Perspectives
© 1998-2012 IEEE. Future 5th generation networks are expected to enable three key services-enhanced mobile broadband, massive machine type communications and ultra-reliable and low latency communications (URLLC). As per the 3rd generation partnership project URLLC requirements, it is expected that the reliability of one transmission of a 32 byte packet will be at least 99.999% and the latency will be at most 1 ms. This unprecedented level of reliability and latency will yield various new applications, such as smart grids, industrial automation and intelligent transport systems. In this survey we present potential future URLLC applications, and summarize the corresponding reliability and latency requirements. We provide a comprehensive discussion on physical (PHY) and medium access control (MAC) layer techniques that enable URLLC, addressing both licensed and unlicensed bands. This paper evaluates the relevant PHY and MAC techniques for their ability to improve the reliability and reduce the latency. We identify that enabling long-term evolution to coexist in the unlicensed spectrum is also a potential enabler of URLLC in the unlicensed band, and provide numerical evaluations. Lastly, this paper discusses the potential future research directions and challenges in achieving the URLLC requirements
A digital signature and watermarking based authentication system for JPEG2000 images
In this thesis, digital signature based authentication system was introduced, which is able to protect JPEG2000 images in different flavors, including fragile authentication and semi-fragile authentication. The fragile authentication is to protect the image at code-stream level, and the semi-fragile is to protect the image at the content level.
The semi-fragile can be further classified into lossy and lossless authentication. With lossless authentication, the original image can be recovered after verification. The lossless authentication and the new image compression standard, JPEG2000 is mainly discussed in this thesis
- …