An approach for smooth trajectory planning of high-speed pick-and-place parallel robots using quintic B-splines

This paper presents a new, highly effective approach for optimal smooth trajectory planning of high-speed pick-and-place parallel robots. The pick-and-place path is decomposed into two orthogonal coordinate axes in the Cartesian space and quintic B-spline curves are used to generate the motion profile along each axis for achieving C4-continuity. By using symmetrical properties of the geometric path defined, the proposed motion profile becomes essentially dominated by two key factors, representing the ratios of the time intervals for the end-effector to move from the initial point to the adjacent virtual and/or the via-points on the path. These two factors can then be determined by maximizing a weighted sum of two normalized single-objective functions and expressed by curve fitting as functions of the width/height ratio of the pick-and-place path, so allowing them to be stored in a look-up table to enable real-time implementation. Experimental results on a 4-DOF SCARA type parallel robot show that the residual vibration of the end-effector can be substantially reduced thanks to the very continuous and smooth joint torques obtained

Fiscal year 1973 scientific and technical reports, articles, papers, and presentations

Formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY73 are presented. Papers of MSFC contractors are also included

Manipulation strategies for massive space payloads

The industrial and environmental applications for robots with a relatively large workspace has increased significantly in the last few years. To accommodate the demands, the manipulator is usually designed with long, lightweight links that are inherently flexible. Ongoing research at Georgia Tech into the behavior and design of these flexible links is discussed

Genetic algorithm optimization and control system design of flexible structures

This paper presents an investigation into the deployment of genetic algorithm (GA)-based controller design and optimization for vibration suppression in flexible structures. The potential of GA is explored in three case studies. In the first case study, the potential of GA is demonstrated in the development and optimization of a hybrid learning control scheme for vibration control of flexible manipulators. In the second case study, an active control mechanism for vibration suppression of flexible beam structures using GA optimization technique is proposed. The third case study presents the development of an effective adaptive command shaping control scheme for vibration control of a twin rotor system, where GA is employed to optimize the amplitudes and time locations of the impulses in the proposed control algorithm. The effectiveness of the proposed control schemes is verified in both an experimental and a simulation environment, and their performances are assessed in both the time and frequency domains

Dynamics and control of a rigid/flexible manipulator

Control of high-speed, light-weight robotic manipulators is a challenge because of their special dynamic characteristics. In this work, a two-stage control algorithm for the position control of flexible manipulators is proposed. First, the more complex, flexible robot system is replaced by a simplified hypothetical rigid body system (HRRA) with off-line trajectory planning. This reduces the complexity of the controller design for the flexible robotic arm. A parameter-optimization approach was adopted to minimize the difference between these two models in this stage. Also, a comparison of computational efficiency is made among the methods of calculus-of-variations, dynamic-programming, and the proposed parameter-optimization. At the second stage, simple linear state feedback controllers, based on the simplified hypothetical rigid body model, are proposed to control the actual robotic system. With the feedback gains selected properly by the pole-placement and linear quadratic methods, the results show satisfactory achievement of the motion objectives. The algorithm is implemented for a two-link rigid/flexible robotic arm, and the results indicate that the procedure is capable of providing effective control with much simpler computational requirements than those of procedures published previously

Method and apparatus for creating time-optimal commands for linear systems

A system for and method of determining an input command profile for substantially any dynamic system that can be modeled as a linear system, the input command profile for transitioning an output of the dynamic system from one state to another state. The present invention involves identifying characteristics of the dynamic system, selecting a command profile which defines an input to the dynamic system based on the identified characteristics, wherein the command profile comprises one or more pulses which rise and fall at switch times, imposing a plurality of constraints on the dynamic system, at least one of the constraints being defined in terms of the switch times, and determining the switch times for the input to the dynamic system based on the command profile and the plurality of constraints. The characteristics may be related to poles and zeros of the dynamic system, and the plurality of constraints may include a dynamics cancellation constraint which specifies that the input moves the dynamic system from a first state to a second state such that the dynamic system remains substantially at the second state

Investigation of the D and E regions of the ionosphere

Details of an experimental program that investigates the ionosphere using sounding rockets are presented. The investigation is part of a continuing program to gather data on the D and E regions of the ionosphere during periods of recurring natural phenomena that influence these regions. To achieve these ends, four vehicles were launched during the eclipse of the sun on March 7, 1970. Other vehicles totalling 10 in all were launched to investigate transient phenomena such as the sporadic E layer

Vibration control for precision manufacturing at Sandia National Laboratories

Sandia National Laboratories performs R and D in structural dynamics and vibration suppression for precision applications in weapon systems, space, underwater, transportation and civil structures. Over the last decade these efforts have expanded into the areas of active vibration control and ``smart`` structures and material systems. In addition, Sandia has focused major resources towards technology to support weapon product development and agile manufacturing capability for defense and industrial applications. This paper will briefly describe the structural dynamics modeling and verification process currently in place at Sandia that supports vibration control and some specific applications of these techniques to manufacturing in the areas of lithography, machine tools and flexible robotics