Programming a Distributed System Using Shared Objects

Building the hardware for a high-performance distributed computer system is a lot easier than building its software. The authors describe a model for programming distributed systems based on abstract data types that can be replicated on all machines that need them. Read operations are done locally, without requiring network traffic. Writes can be done using a reliable broadcast algorithm if the hardware supports broadcasting; otherwise, a point-to-point protocol is used. The authors have built such a system based on the Amoeba microkernel, and implemented a language, Orca, on top of it. For Orca applications that have a high ratio of reads to writes, they measure good speedups on a system with 16 processors

REDUCING POWER DURING MANUFACTURING TEST USING DIFFERENT ARCHITECTURES

Power during manufacturing test can be several times higher than power consumption in functional mode. Excessive power during test can cause IR drop, over-heating, and early aging of the chips. In this dissertation, three different architectures have been introduced to reduce test power in general cases as well as in certain scenarios, including field test. In the first architecture, scan chains are divided into several segments. Every segment needs a control bit to enable capture in a segment when new faults are detectable on that segment for that pattern. Otherwise, the segment should be disabled to reduce capture power. We group the control bits together into one or more control chains. To address the extra pin(s) required to shift data into the control chain(s) and significant post processing in the first architecture, we explored a second architecture. The second architecture stitches the control bits into the chains they control as EECBs (embedded enable capture bits) in between the segments. This allows an ATPG software tool to automatically generate the appropriate EECB values for each pattern to maintain the fault coverage. This also works in the presence of an on-chip decompressor. The last architecture focuses primarily on the self-test of a device in a 3D stacked IC when an existing FPGA in the stack can be programmed as a tester. We show that the energy expended during test is significantly less than would be required using low power patterns fed by an on-chip decompressor for the same very short scan chains

Automatic test pattern generation for asynchronous circuits

The testability of integrated circuits becomes worse with transistor dimensions reaching nanometer scales. Testing, the process of ensuring that circuits are fabricated without defects, becomes inevitably part of the design process; a technique called design for test (DFT). Asynchronous circuits have a number of desirable properties making them suitable for the challenges posed by modern technologies, but are severely limited by the unavailability of EDA tools for DFT and automatic test-pattern generation (ATPG). This thesis is motivated towards developing test generation methodologies for asynchronous circuits. In total four methods were developed which are aimed at two different fault models: stuck-at faults at the basic logic gate level and transistor-level faults. The methods were evaluated using a set of benchmark circuits and compared favorably to previously published work. First, ABALLAST is a partial-scan DFT method adapting the well-known BALLAST technique for asynchronous circuits where balanced structures are used to guide the selection of the state-holding elements that will be scanned. The test inputs are automatically provided by a novel test pattern generator, which uses time frame unrolling to deal with the remaining, non-scanned sequential C-elements. The second method, called AGLOB, uses algorithms from strongly-connected components in graph graph theory as a method for finding the optimal position of breaking the loops in the asynchronous circuit and adding scan registers. The corresponding ATPG method converts cyclic circuits into acyclic for which standard tools can provide test patterns. These patterns are then automatically converted for use in the original cyclic circuits. The third method, ASCP, employs a new cycle enumeration method to find the loops present in a circuit. Enumerated cycles are then processed using an efficient set covering heuristic to select the scan elements for the circuit to be tested.Applying these methods to the benchmark circuits shows an improvement in fault coverage compared to previous work, which, for some circuits, was substantial. As no single method consistently outperforms the others in all benchmarks, they are all valuable as a designer’s suite of tools for testing. Moreover, since they are all scan-based, they are compatible and thus can be simultaneously used in different parts of a larger circuit. In the final method, ATRANTE, the main motivation of developing ATPG is supplemented by transistor level test generation. It is developed for asynchronous circuits designed using a State Transition Graph (STG) as their specification. The transistor-level circuit faults are efficiently mapped onto faults that modify the original STG. For each potential STG fault, the ATPG tool provides a sequence of test vectors that expose the difference in behavior to the output ports. The fault coverage obtained was 52-72 % higher than the coverage obtained using the gate level tests. Overall, four different design for test (DFT) methods for automatic test pattern generation (ATPG) for asynchronous circuits at both gate and transistor level were introduced in this thesis. A circuit extraction method for representing the asynchronous circuits at a higher level of abstraction was also implemented. Developing new methods for the test generation of asynchronous circuits in this thesis facilitates the test generation for asynchronous designs using the CAD tools available for testing the synchronous designs. Lessons learned and the research questions raised due to this work will impact the future work to probe the possibilities of developing robust CAD tools for testing the future asynchronous designs

Fault Detection Methodology for Caches in Reliable Modern VLSI Microprocessors based on Instruction Set Architectures

Η παρούσα διδακτορική διατριβή εισάγει μία χαμηλού κόστους μεθοδολογία για την ανίχνευση ελαττωμάτων σε μικρές ενσωματωμένες κρυφές μνήμες που βασίζεται σε σύγχρονες Αρχιτεκτονικές Συνόλου Εντολών και εφαρμόζεται με λογισμικό αυτοδοκιμής. Η προτεινόμενη μεθοδολογία εφαρμόζει αλγορίθμους March μέσω λογισμικού για την ανίχνευση τόσο ελαττωμάτων αποθήκευσης όταν εφαρμόζεται σε κρυφές μνήμες που περιέχουν μόνο στατικές μνήμες τυχαίας προσπέλασης όπως για παράδειγμα κρυφές μνήμες επιπέδου 1, όσο και ελαττωμάτων σύγκρισης όταν εφαρμόζεται σε κρυφές μνήμες που περιέχουν εκτός από SRAM μνήμες και μνήμες διευθυνσιοδοτούμενες μέσω περιεχομένου, όπως για παράδειγμα πλήρως συσχετιστικές κρυφές μνήμες αναζήτησης μετάφρασης. Η προτεινόμενη μεθοδολογία εφαρμόζεται και στις τρεις οργανώσεις συσχετιστικότητας κρυφής μνήμης και είναι ανεξάρτητη της πολιτικής εγγραφής στο επόμενο επίπεδο της ιεραρχίας. Η μεθοδολογία αξιοποιεί υπάρχοντες ισχυρούς μηχανισμούς των μοντέρνων ISAs χρησιμοποιώντας ειδικές εντολές, που ονομάζονται στην παρούσα διατριβή Εντολές Άμεσης Προσπέλασης Κρυφής Μνήμης (Direct Cache Access Instructions - DCAs). Επιπλέον, η προτεινόμενη μεθοδολογία εκμεταλλεύεται τους έμφυτους μηχανισμούς καταγραφής απόδοσης και τους μηχανισμούς χειρισμού παγίδων που είναι διαθέσιμοι στους σύγχρονους επεξεργαστές. Επιπρόσθετα, η προτεινόμενη μεθοδολογία εφαρμόζει την λειτουργία σύγκρισης των αλγορίθμων March όταν αυτή απαιτείται (για μνήμες CAM) και επαληθεύει το αποτέλεσμα του ελέγχου μέσω σύντομης απόκρισης, ώστε να είναι συμβατή με τις απαιτήσεις του ελέγχου εντός λειτουργίας. Τέλος, στη διατριβή προτείνεται μία βελτιστοποίηση της μεθοδολογίας για πολυνηματικές, πολυπύρηνες αρχιτεκτονικές.The present PhD thesis introduces a low cost fault detection methodology for small embedded cache memories that is based on modern Instruction Set Architectures and is applied with Software-Based Self-Test (SBST) routines. The proposed methodology applies March tests through software to detect both storage faults when applied to caches that comprise Static Random Access Memories (SRAM) only, e.g. L1 caches, and comparison faults when applied to caches that apart from SRAM memories comprise Content Addressable Memories (CAM) too, e.g. Translation Lookaside Buffers (TLBs). The proposed methodology can be applied to all three cache associativity organizations: direct mapped, set-associative and full-associative and it does not depend on the cache write policy. The methodology leverages existing powerful mechanisms of modern ISAs by utilizing instructions that we call in this PhD thesis Direct Cache Access (DCA) instructions. Moreover, our methodology exploits the native performance monitoring hardware and the trap handling mechanisms which are available in modern microprocessors. Moreover, the proposed Methodology applies March compare operations when needed (for CAM arrays) and verifies the test result with a compact response to comply with periodic on-line testing needs. Finally, a multithreaded optimization of the proposed methodology that targets multithreaded, multicore architectures is also presented in this thesi

ProperCAD II: A Run-Time Library for Portable, Parallel, Object-Oriented Programming with Applications to VLSI CAD

Coordinated Science Laboratory was formerly known as Control Systems LaboratorySemiconductor Research Corporation / grant 93-DP-10

Cost modelling and concurrent engineering for testable design

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.As integrated circuits and printed circuit boards increase in complexity, testing becomes a major cost factor of the design and production of the complex devices. Testability has to be considered during the design of complex electronic systems, and automatic test systems have to be used in order to facilitate the test. This fact is now widely accepted in industry. Both design for testability and the usage of automatic test systems aim at reducing the cost of production testing or, sometimes, making it possible at all. Many design for testability methods and test systems are available which can be configured into a production test strategy, in order to achieve high quality of the final product. The designer has to select from the various options for creating a test strategy, by maximising the quality and minimising the total cost for the electronic system. This thesis presents a methodology for test strategy generation which is based on consideration of the economics during the life cycle of the electronic system. This methodology is a concurrent engineering approach which takes into account all effects of a test strategy on the electronic system during its life cycle by evaluating its related cost. This objective methodology is used in an original test strategy planning advisory system, which allows for test strategy planning for VLSI circuits as well as for digital electronic systems. The cost models which are used for evaluating the economics of test strategies are described in detail and the test strategy planning system is presented. A methodology for making decisions which are based on estimated costing data is presented. Results of using the cost models and the test strategy planning system for evaluating the economics of test strategies for selected industrial designs are presented

FPGA Based Design for Accelerated Fault-testing of Integrated Circuits

In the past few decades, integrated circuits have become a major part of everyday life. Every circuit that is created needs to be tested for faults so faulty circuits are not sent to end-users. The creation of these tests is time consuming, costly and difficult to perform on larger circuits. This research presents a novel method for fault detection and test pattern reduction in integrated circuitry under test. By leveraging the FPGA\u27s reconfigurability and parallel processing capabilities, a speed up in fault detection can be achieved over previous computer simulation techniques. This work presents the following contributions to the field of Stuck-At-Fault detection: We present a new method for inserting faults into a circuit net list. Given any circuit netlist, our tool can insert multiplexers into a circuit at correct internal nodes to aid in fault emulation on reconfigurable hardware. We present a parallel method of fault emulation. The benefit of the FPGA is not only its ability to implement any circuit, but its ability to process data in parallel. This research utilizes this to create a more efficient emulation method that implements numerous copies of the same circuit in the FPGA. A new method to organize the most efficient faults. Most methods for determinin the minimum number of inputs to cover the most faults require sophisticated softwareprograms that use heuristics. By utilizing hardware, this research is able to process data faster and use a simpler method for an efficient way of minimizing inputs

New Techniques for On-line Testing and Fault Mitigation in GPUs

L'abstract è presente nell'allegato / the abstract is in the attachmen

SCAN CHAIN BASED HARDWARE SECURITY

Hardware has become a popular target for attackers to hack into any computing and communication system. Starting from the legendary power analysis attacks discovered 20 years ago to the recent Intel Spectre and Meltdown attacks, security vulnerabilities in hardware design have been exploited for malicious purposes. With the emerging Internet of Things (IoT) applications, where the IoT devices are extremely resource constrained, many proven secure but computational expensive cryptography protocols cannot be applied on such devices. Thus there is an urgent need to understand the hardware vulnerabilities and develop cost effective mitigation methods. One established field in the semiconductor and integrated circuit (IC) industry, known as IC test, has the goal of ensuring that fabricated ICs are free of manufacturing defects and perform the required functionalities. Testing is essential to isolate faulty chips from good ones. The concept of design for test (DFT) has been integrated in the commercial IC design and fabrication process for several decades. Scan chain, which provides test engineer access to all the flip flops in the chip through the scan in (SI) and scan out (SO) ports, is the backbone of industrial testing methods and can be found in almost all the modern designs. In addition to IC testing, scan chain has found applications in intellectual property (IP) protection and IC identification. However, attackers can also leverage the controllability and observability of scan chain as a side channel to break systems such as cryptographic chips. This dissertation addresses these two important security problems by proposing (1) a practical scan chain based security primitive for IP protection and (2) a partial scan chain framework that can mitigate all the existing scan based attacks. First, we observe the fact that each D-flip-flop has two output ports, Q and Q’, designed to simplify the logic and has been used to reduce the power consumption for IC test. The availability of both Q and Q’ ports provide the opportunity for IP protection. More specifically, we can generate a digital fingerprint by selecting different connection styles between adjacent scan cells during the design of scan chain. This method has two major advantages: fingerprints are created as a post-silicon procedure and therefore there will be little fabrication overhead; altering the connection style requires the modification of test vectors for each fingerprinted IP and thus enables a non-intrusive fingerprint verification method. This addresses the overhead and detectability problems, two of the most challenging problems of designing practical IP fingerprinting techniques in the past two decades. Combined with the recently developed reconfigurable scan networks (RSNs) that are popular for embedded and IoT devices, we design an IC identification (ID) scheme utilizing the different connection styles. We perform experiments on standard benchmarks to demonstrate that our approach has low design overhead. We also conduct security analysis to show that such fingerprints and IC IDs are robust against various attacks. In the second part of this dissertation, we consider the scan chain side channel attack, which has been reported as one of the most severe side channel attacks to modern secure systems. We argue that the current countermeasures are restricted to the requirement of providing direct SI and SO for testing and thus suffers the vulnerability of leaving this side channel open to the attackers as well. Therefore, we propose a novel public-private partial scan chain based approach with the basic idea of removing the flip flops that store sensitive information from the scan chain. This will eliminate the scan chain side channel, but it also limits IC test. The key contribution in our proposed public-private partial scan chain design is that it can keep the full test coverage while providing security to the scan chain. This is achieved by chaining the removed flip flops into one or more private partial scan chains and adding protections to the SI and SO ports of such chains. Unlike the traditional partial scan design which not only fails to provide full fault coverage, but also incur huge overhead in test time and test vector generation time, we propose a set of techniques to ensure that the desired test vectors can be entered into the system efficiently. These techniques include test vector reordering, test vector reusing, and test vector generation based on a novel finite state machine (FSM) structure we have invented. On the other hand, to enable the test engineers the ability to observe the test output to diagnose the chip while not leaking information to the attackers, we propose two lightweight mechanisms, one based on linear feedback shift register (LFSR) and the other one based on configurable physical unclonable function (PUF). Finally, we discuss a protocol on how in-field test can be realized using our public-private partial scan chain. We conduct experiments with industrial scan design tools to demonstrate that the required hardware in our approach has negligible area overhead and gives full test coverage with reduced test time and does not need to re-generate test vectors. In sum, this dissertation focuses on the role of scan chain, a conventional design for test facility, in hardware security. We show that scan chain features can be leveraged to create practical IP protection techniques including IP watermarking and fingerprinting as well as IC identification and authentication. We also propose a novel public-private partial scan design principle to close the scan chain side channel to the attackers. Through this dissertation work, we demonstrate that it is possible to develop highly practical scan chain based techniques that can benefit both the community of IC test and hardware security

Techniques for Improving Security and Trustworthiness of Integrated Circuits

The integrated circuit (IC) development process is becoming increasingly vulnerable to malicious activities because untrusted parties could be involved in this IC development flow. There are four typical problems that impact the security and trustworthiness of ICs used in military, financial, transportation, or other critical systems: (i) Malicious inclusions and alterations, known as hardware Trojans, can be inserted into a design by modifying the design during GDSII development and fabrication. Hardware Trojans in ICs may cause malfunctions, lower the reliability of ICs, leak confidential information to adversaries or even destroy the system under specifically designed conditions. (ii) The number of circuit-related counterfeiting incidents reported by component manufacturers has increased significantly over the past few years with recycled ICs contributing the largest percentage of the total reported counterfeiting incidents. Since these recycled ICs have been used in the field before, the performance and reliability of such ICs has been degraded by aging effects and harsh recycling process. (iii) Reverse engineering (RE) is process of extracting a circuit’s gate-level netlist, and/or inferring its functionality. The RE causes threats to the design because attackers can steal and pirate a design (IP piracy), identify the device technology, or facilitate other hardware attacks. (iv) Traditional tools for uniquely identifying devices are vulnerable to non-invasive or invasive physical attacks. Securing the ID/key is of utmost importance since leakage of even a single device ID/key could be exploited by an adversary to hack other devices or produce pirated devices. In this work, we have developed a series of design and test methodologies to deal with these four challenging issues and thus enhance the security, trustworthiness and reliability of ICs. The techniques proposed in this thesis include: a path delay fingerprinting technique for detection of hardware Trojans, recycled ICs, and other types counterfeit ICs including remarked, overproduced, and cloned ICs with their unique identifiers; a Built-In Self-Authentication (BISA) technique to prevent hardware Trojan insertions by untrusted fabrication facilities; an efficient and secure split manufacturing via Obfuscated Built-In Self-Authentication (OBISA) technique to prevent reverse engineering by untrusted fabrication facilities; and a novel bit selection approach for obtaining the most reliable bits for SRAM-based physical unclonable function (PUF) across environmental conditions and silicon aging effects