Strategies for enhancing DC gain and settling performance of amplifiers

The operational amplifier (op amp) is one of the most widely used and important building blocks in analog circuit design. High gain and high speed are two important properties of op amps because they determine the settling behavior of the op amps. As supply voltages decrease, the realization of high gain amplifiers with large Gain-Bandwidth-Products (GBW) has become challenging. The major focus in this dissertation is on the negative output impedance gain enhancement technique. The negative impedance gain enhancement technique offers potential for achieving very high gain and energy-efficient fast settling and is low-voltage compatible. Misconceptions that have limited the practical adoption of this gain enhancement technique are discussed. A new negative conductance gain enhancement technique was proposed. The proposed circuit generates a negative conductance with matching requirements for achieving very high DC gain that are less stringent than those for existing -g m gain enhancement schemes. The proposed circuit has potential for precise digital control of a very large DC gain. A prototype fully differential CMOS operational amplifier was designed and fabricated based on the proposed gain enhancement technique. Experimental results which showed a DC gain of 85dB and an output swing of 876mVp-p validated the fundamental performance characteristics of this technique. In a separate section, a new amplifier architecture with bandpass feedforward compensation is presented. It is shown that a bandpass feedforward path can be used to substantially extend the unity-gain-frequency of an operational amplifier. Simulation results predict significant improvements in rise time and settling performance and show that the bandpass compensation scheme is reasonably robust. In the final section, a new technique for asynchronous data recovery based upon using a delay line in the incoming data path is introduced. The proposed data recovery system is well suited for tight tolerance channels and coding systems supporting standards that limit the maximum number of consecutive 0\u27s and 1\u27s in a data stream. This system does not require clock recovery, suffers no loss of data during acquisition, has a reduced sensitivity to jitter in the incoming data and does not exhibit jitter enhancement associated with VCO tracking in a PLL

A 90 dB, 85 MHz operational transconductance amplifier (OTA) using gain boosting technique

Gain and speed are the two most important parameters of an amplifier. Optimizing an amplifier for both of these parameters leads to contradicting demands. Various architectures have been reported to obtain high gain from the circuits. Cascode circuits are widely used in circuit design at places where high gain and high output impedances are required. Different architectures like triple cascode topology, dynamic biasing and a positive feedback amplifier have been used to obtain high gains. These architectures have been compared in this thesis along with drawbacks and advantages of each

New mathematical formulation for designing a fully differential self-biased folded cascode amplifier

One of the most important building blocks in analog circuit design is the operational amplifiers. This is because of their versatility and wide spread usage in many applications such as communications transmitters and receivers, analog to digital converters, or any other application that requires a small signal to be amplified. The basic amplifier topologies are introduced. Then, some operational amplifiers topologies are introduced with some techniques to self bias these amplifiers. The folded cascode fully differential Op-Amp with self bias is presented. This is one of the newest amplifier topologies which provide stable self-biased amplifiers. A new mathematical model for fully differential folded cascode amplifiers is presented and generalized to include the family of fully differential complementary amplifiers. This formulation focuses on deriving detailed design equations for the amplifier gain and frequency response. The equations are verified through time domain and frequency domain simulations of different fabrication processes to ensure the validity of the model across a wide range of processes. The model was verified against TMSC 180nm, 250nm, and 350nm fabrication processes. The new model agrees well with simulations; with 1% error for the amplifier gain and \u3c7% error for amplifier bandwidth. The relatively high error value for the bandwidth is because the model considers the worst case scenario and overestimates the output capacitance. Finally, the algorithm of getting this formulation is extended to include special and commonly used cases. This formulation proved to be very useful in designing stable, self-biased, fully differential folded cascode amplifiers

Time-domain optimization of amplifiers based on distributed genetic algorithms

Thesis presented in partial fulfillment of the requirements for the degree of Doctor of Philosophy in the subject of Electrical and Computer EngineeringThe work presented in this thesis addresses the task of circuit optimization, helping the designer facing the high performance and high efficiency circuits demands of the market and technology evolution. A novel framework is introduced, based on time-domain analysis, genetic algorithm optimization, and distributed processing. The time-domain optimization methodology is based on the step response of the amplifier. The main advantage of this new time-domain methodology is that, when a given settling-error is reached within the desired settling-time, it is automatically guaranteed that the amplifier has enough open-loop gain, AOL, output-swing (OS), slew-rate (SR), closed loop bandwidth and closed loop stability. Thus, this simplification of the circuit‟s evaluation helps the optimization process to converge faster. The method used to calculate the step response expression of the circuit is based on the inverse Laplace transform applied to the transfer function, symbolically, multiplied by 1/s (which represents the unity input step). Furthermore, may be applied to transfer functions of circuits with unlimited number of zeros/poles, without approximation in order to keep accuracy. Thus, complex circuit, with several design/optimization degrees of freedom can also be considered. The expression of the step response, from the proposed methodology, is based on the DC bias operating point of the devices of the circuit. For this, complex and accurate device models (e.g. BSIM3v3) are integrated. During the optimization process, the time-domain evaluation of the amplifier is used by the genetic algorithm, in the classification of the genetic individuals. The time-domain evaluator is integrated into the developed optimization platform, as independent library, coded using C programming language. The genetic algorithms have demonstrated to be a good approach for optimization since they are flexible and independent from the optimization-objective. Different levels of abstraction can be optimized either system level or circuit level. Optimization of any new block is basically carried-out by simply providing additional configuration files, e.g. chromosome format, in text format; and the circuit library where the fitness value of each individual of the genetic algorithm is computed. Distributed processing is also employed to address the increasing processing time demanded by the complex circuit analysis, and the accurate models of the circuit devices. The communication by remote processing nodes is based on Message Passing interface (MPI). It is demonstrated that the distributed processing reduced the optimization run-time by more than one order of magnitude. Platform assessment is carried by several examples of two-stage amplifiers, which have been optimized and successfully used, embedded, in larger systems, such as data converters. A dedicated example of an inverter-based self-biased two-stage amplifier has been designed, laid-out and fabricated as a stand-alone circuit and experimentally evaluated. The measured results are a direct demonstration of the effectiveness of the proposed time-domain optimization methodology.Portuguese Foundation for the Science and Technology (FCT

Super-gain-boosted AB-AB fully differential Miller op-amp with 156dB open-loop gain and 174MV/V MHZ pF/uW figure of merit in 130nm CMOS technology

A fully differential Miller op-amp with a composite input stage using resistive local common-mode feedback and regulated cascode transistors is presented here. High gain pseudo-differential auxiliary amplifiers are used to implement the regulated cascode transistors in order to boost the output impedance of the composite input stage and the open-loop gain of the op-amp. Both input and output stages operate in class AB mode. The proposed op-amp has been simulated in a 130nm commercial CMOS process technology. It operates from a 1.2V supply and has a close to rail-to-rail differential output swing. It has 156dB DC open-loop gain and 63MHz gain-bandwidth product with a 30pF capacitive load. The op-amp has a DC open-loop gain figure of merit FOMAOLDC of 174 (MV/V) MHz pF/uW and large-signal figure of merit FOMLS of 3(V/us) pF/uW.This work was supported in part by the Spanish Government Agencia Estatal de Investigación (AEI) under Grant TEC2016-80396-C2, in part by the Consejería de Economía y Conocimiento of Junta de Andalucía under Grant P18-FR-4317 (both projects received support from the Fondo Europeo de Desarrollo Regional (FEDER)), and in part by the Consejo Nacional de Ciencia y Tecnologia (CONACyT) under Grant A1-S-43214

Super-Gain-Boosted AB-AB Fully Differential Miller Op-Amp With 156dB Open-Loop Gain and 174MV/V MHZ pF/µW Figure of Merit in 130nm CMOS Technology

Article number 9400400A fully differential Miller op-amp with a composite input stage using resistive local common-mode feedback and regulated cascode transistors is presented here. High gain pseudo-differential auxiliary amplifiers are used to implement the regulated cascode transistors in order to boost the output impedance of the composite input stage and the open-loop gain of the op-amp. Both input and output stages operate in class AB mode. The proposed op-amp has been simulated in a 130nm commercial CMOS process technology. It operates from a 1.2V supply and has a close to rail-to-rail differential output swing. It has 156dB DC open-loop gain and 63MHz gain-bandwidth product with a 30pF capacitive load. The op-amp has a DC open-loop gain figure of merit FOMAOLDC of 174 (MV/V) MHz pF/µW and large-signal figure of merit FOMLS of 3(V/µs) pF/µW.Consejería de Economía y Conocimiento of Junta de Andalucía P18-FR-4317Consejo Nacional de Ciencia y Tecnología (España) A1-S-43214Agencia Estatal de Investigación TEC2016-80396-C

A fully-integrated 180 nm CMOS 1.2 V low-dropout regulator for low-power portable applications

This paper presents the design and postlayout simulation results of a capacitor-less low dropout (LDO) regulator fully integrated in a low-cost standard 180 nm Complementary Metal-Oxide-Semiconductor (CMOS) technology which regulates the output voltage at 1.2 V from a 3.3 to 1.3 V battery over a -40 to 120 degrees C temperature range. To meet with the constraints of system-on-chip (SoC) battery-operated devices, ultralow power (I-q = 8.6 mu A) and minimum area consumption (0.109 mm(2)) are maintained, including a reference voltage V-ref = 0.4 V. It uses a high-gain dynamically biased folded-based error amplifier topology optimized for low-voltage operation that achieves an enhanced regulation-fast transient performance trade-off

Design of Analog CMOS Circuits for Batteryless Implantable Telemetry Systems

A wireless biomedical telemetry system is a device that collects biomedical signal measurements and transmits data through wireless RF communication. Testing medical treatments often involves experimentation on small laboratory animals, such as genetically modified mice and rats. Using batteries as a power source results in many practical issues, such as increased size of the implant and limited operating lifetime. Wireless power harvesting for implantable biomedical devices removes the need for batteries integrated into the implant. This will reduce device size and remove the need for surgical replacement due to battery depletion. Resonant inductive coupling achieves wireless power transfer in a manner modelled by a step down transformer. With this methodology, power harvesting for an implantable device is realized with the use of a large primary coil external to the subject, and a smaller secondary coil integrated into the implant. The signal received from the secondary coil must be regulated to provide a stable direct current (DC) power supply, which will be used to power the electronics in the implantable device. The focus of this work is on development of an electronic front-end for wireless powering of an implantable biomedical device. The energy harvesting front-end circuit is comprised of a rectifier, LDO regulator, and a temperature insensitive voltage reference. Physical design of the front-end circuit is developed in 0.13um CMOS technology with careful attention to analog layout issues. Post-layout simulation results are presented for each sub-block as well as the full front-end structure. The LDO regulator operates with supply voltages in the range of 1V to 1.5V with quiescent current of 10.5uA The complete power receiver front-end has a power conversion efficiency of up to 29%