Automated Exploration of the ASIC Design Space for Minimum Power-Delay-Area Product at the Register Transfer Level

Exploring the integrated circuit design space for minimum power-delay-area (PDA) product can be time-consuming and tedious, especially when the target standard-cell library has hundreds of options. In this dissertation, heuristic algorithms that automate this process have been developed, implemented and validated at the reg- ister transfer level. In some cases, the PDA product was 1.9 times better than the initial baseline solution. The parallel search algorithm exhibited 9x speed up when executed on 10 machines simultaneously. These two new methods also characterize the design space for the given RTL code by generating power-delay-area points in addition to the minimum PDA point in case the designer wishes to select a different solution that is a tradeoff among these metrics. As a final step, these two search algorithms are integrated into a fully automated ASIC design flow

Implementation Of Modular Testing In Bios Development And Debug

This project presents a modular approach in BIOS development in purpose to tackle the problem of long development time with the existing methodologies which are hardware platform approach and virtual platform approach. The proposed approach consists of previous generation platform, a FPGA card and UEFI drivers. The FPGA is loaded with the RTL of one Intellectual Property (IP) from the current company project. The chosen IP is Low Power Subsystem (LPSS). The card is then plugged into the PCI slot of the platform. Besides, UEFI Configuration Driver and UEFI Reset Driver are built to configure and reset the LPSS registers respectively. Both of them are stored into a thumb drive and plugged into USB port of the platform. They are executed in the UEFI Shell environment. In this project, the development time of LPSS needed by the three methodologies which are hardware platform approach, virtual platform approach and modular approach are compared. The results indicate that modular approach is capable to save up to 90% of the development time in comparison with the other two approaches. At the same time, both of the UEFI drivers are functioning correctly. The processing time of both of the UEFI Configuration Driver and UEFI Reset Driver are about 1 to 2 seconds only. In conclusion, the novelty of the modular approach is that the BIOS can be developed in modular basis, without having to develop the BIOS as a whole. Therefore, it is able to cut down the BIOS development time efficientl

A Structured Design Methodology for High Performance VLSI Arrays

abstract: The geometric growth in the integrated circuit technology due to transistor scaling also with system-on-chip design strategy, the complexity of the integrated circuit has increased manifold. Short time to market with high reliability and performance is one of the most competitive challenges. Both custom and ASIC design methodologies have evolved over the time to cope with this but the high manual labor in custom and statistic design in ASIC are still causes of concern. This work proposes a new circuit design strategy that focuses mostly on arrayed structures like TLB, RF, Cache, IPCAM etc. that reduces the manual effort to a great extent and also makes the design regular, repetitive still achieving high performance. The method proposes making the complete design custom schematic but using the standard cells. This requires adding some custom cells to the already exhaustive library to optimize the design for performance. Once schematic is finalized, the designer places these standard cells in a spreadsheet, placing closely the cells in the critical paths. A Perl script then generates Cadence Encounter compatible placement file. The design is then routed in Encounter. Since designer is the best judge of the circuit architecture, placement by the designer will allow achieve most optimal design. Several designs like IPCAM, issue logic, TLB, RF and Cache designs were carried out and the performance were compared against the fully custom and ASIC flow. The TLB, RF and Cache were the part of the HEMES microprocessor.Dissertation/ThesisPh.D. Electrical Engineering 201

Algorithmic techniques for physical design : macro placement and under-the-cell routing

With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure. This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time. The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing. The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search. Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi.Postprint (published version

Algorithmic techniques for physical design : macro placement and under-the-cell routing

With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure. This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time. The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing. The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search. Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi

EPICURE: A partitioning and co-design framework for reconfigurable computing

This paper presents a new design methodology able to bridge the gap between an abstract specification and a heterogeneous reconfigurable architecture. The EPICURE contribution is the result of a joint study on abstraction/refinement methods and a smart reconfigurable architecture within the formal Esterel design tools suite. The original points of this work are: (i) a generic HW/SW interface model, (ii) a specification methodology that handles the control, and includes efficient verification and HW/SW synthesis capabilities, (iii) a method for parallelism exploration based on abstract resources/performance estimation expressed in terms of area/delay tradeoffs, (iv) a HW/SW partitioning approach that refines the specification into explicit HW configurations and the associated SW control. The EPICURE framework shows how a cooperation of complementary methodologies and CAD tools associated with a relevant architecture can signficantly improve the designer productivity, especially in the context of reconfigurable architectures

A comprehensive comparison between design for testability techniques for total dose testing of flash-based FPGAs

Radiation sources exist in different kinds of environments where electronic devices often operate. Correct device operation is usually affected negatively by radiation. The radiation resultant effect manifests in several forms depending on the operating environment of the device like total ionizing dose effect (TID), or single event effects (SEEs) such as single event upset (SEU), single event gate rupture (SEGR), and single event latch up (SEL). CMOS circuits and Floating gate MOS circuits suffer from an increase in the delay and the leakage current due to TID effect. This may damage the proper operation of the integrated circuit. Exhaustive testing is needed for devices operating in harsh conditions like space and military applications to ensure correct operations in the worst circumstances. The use of worst case test vectors (WCTVs) for testing is strongly recommended by MIL-STD-883, method 1019, which is the standard describing the procedure for testing electronic devices under radiation. However, the difficulty of generating these test vectors hinders their use in radiation testing. Testing digital circuits in the industry is usually done nowadays using design for testability (DFT) techniques as they are very mature and can be relied on. DFT techniques include, but not limited to, ad-hoc technique, built-in self test (BIST), muxed D scan, clocked scan and enhanced scan. DFT is usually used with automatic test patterns generation (ATPG) software to generate test vectors to test application specific integrated circuits (ASICs), especially with sequential circuits, against faults like stuck at faults and path delay faults. Despite all these recommendations for DFT, radiation testing has not benefited from this reliable technology yet. Also, with the big variation in the DFT techniques, choosing the right technique is the bottleneck to achieve the best results for TID testing. In this thesis, a comprehensive comparison between different DFT techniques for TID testing of flash-based FPGAs is made to help designers choose the best suitable DFT technique depending on their application. The comparison includes muxed D scan technique, clocked scan technique and enhanced scan technique. The comparison is done using ISCAS-89 benchmarks circuits. Points of comparisons include FPGA resources utilization, difficulty of designs bring-up, added delay by DFT logic and robust testable paths in each technique