Robust low-power digital circuit design in nano-CMOS technologies

Device scaling has resulted in large scale integrated, high performance, low-power, and low cost systems. However the move towards sub-100 nm technology nodes has increased variability in device characteristics due to large process variations. Variability has severe implications on digital circuit design by causing timing uncertainties in combinational circuits, degrading yield and reliability of memory elements, and increasing power density due to slow scaling of supply voltage. Conventional design methods add large pessimistic safety margins to mitigate increased variability, however, they incur large power and performance loss as the combination of worst cases occurs very rarely. In-situ monitoring of timing failures provides an opportunity to dynamically tune safety margins in proportion to on-chip variability that can significantly minimize power and performance losses. We demonstrated by simulations two delay sensor designs to detect timing failures in advance that can be coupled with different compensation techniques such as voltage scaling, body biasing, or frequency scaling to avoid actual timing failures. Our simulation results using 45 nm and 32 nm technology BSIM4 models indicate significant reduction in total power consumption under temperature and statistical variations. Future work involves using dual sensing to avoid useless voltage scaling that incurs a speed loss. SRAM cache is the first victim of increased process variations that requires handcrafted design to meet area, power, and performance requirements. We have proposed novel 6 transistors (6T), 7 transistors (7T), and 8 transistors (8T)-SRAM cells that enable variability tolerant and low-power SRAM cache designs. Increased sense-amplifier offset voltage due to device mismatch arising from high variability increases delay and power consumption of SRAM design. We have proposed two novel design techniques to reduce offset voltage dependent delays providing a high speed low-power SRAM design. Increasing leakage currents in nano-CMOS technologies pose a major challenge to a low-power reliable design. We have investigated novel segmented supply voltage architecture to reduce leakage power of the SRAM caches since they occupy bulk of the total chip area and power. Future work involves developing leakage reduction methods for the combination logic designs including SRAM peripherals

Solid State Circuits Technologies

The evolution of solid-state circuit technology has a long history within a relatively short period of time. This technology has lead to the modern information society that connects us and tools, a large market, and many types of products and applications. The solid-state circuit technology continuously evolves via breakthroughs and improvements every year. This book is devoted to review and present novel approaches for some of the main issues involved in this exciting and vigorous technology. The book is composed of 22 chapters, written by authors coming from 30 different institutions located in 12 different countries throughout the Americas, Asia and Europe. Thus, reflecting the wide international contribution to the book. The broad range of subjects presented in the book offers a general overview of the main issues in modern solid-state circuit technology. Furthermore, the book offers an in depth analysis on specific subjects for specialists. We believe the book is of great scientific and educational value for many readers. I am profoundly indebted to the support provided by all of those involved in the work. First and foremost I would like to acknowledge and thank the authors who worked hard and generously agreed to share their results and knowledge. Second I would like to express my gratitude to the Intech team that invited me to edit the book and give me their full support and a fruitful experience while working together to combine this book

Ultra Low Power Digital Circuit Design for Wireless Sensor Network Applications

Ny forskning innenfor feltet trådløse sensornettverk åpner for nye og innovative produkter og løsninger. Biomedisinske anvendelser er blant områdene med størst potensial og det investeres i dag betydelige beløp for å bruke denne teknologien for å gjøre medisinsk diagnostikk mer effektiv samtidig som man åpner for fjerndiagnostikk basert på trådløse sensornoder integrert i et ”helsenett”. Målet er å forbedre tjenestekvalitet og redusere kostnader samtidig som brukerne skal oppleve forbedret livskvalitet som følge av økt trygghet og mulighet for å tilbringe mest mulig tid i eget hjem og unngå unødvendige sykehusbesøk og innleggelser. For å gjøre dette til en realitet er man avhengige av sensorelektronikk som bruker minst mulig energi slik at man oppnår tilstrekkelig batterilevetid selv med veldig små batterier. I sin avhandling ” Ultra Low power Digital Circuit Design for Wireless Sensor Network Applications” har PhD-kandidat Farshad Moradi fokusert på nye løsninger innenfor konstruksjon av energigjerrig digital kretselektronikk. Avhandlingen presenterer nye løsninger både innenfor aritmetiske og kombinatoriske kretser, samtidig som den studerer nye statiske minneelementer (SRAM) og alternative minnearkitekturer. Den ser også på utfordringene som oppstår når silisiumteknologien nedskaleres i takt med mikroprosessorutviklingen og foreslår løsninger som bidrar til å gjøre kretsløsninger mer robuste og skalerbare i forhold til denne utviklingen. De viktigste konklusjonene av arbeidet er at man ved å introdusere nye konstruksjonsteknikker både er i stand til å redusere energiforbruket samtidig som robusthet og teknologiskalerbarhet øker. Forskningen har vært utført i samarbeid med Purdue University og vært finansiert av Norges Forskningsråd gjennom FRINATprosjektet ”Micropower Sensor Interface in Nanometer CMOS Technology”

A Process Variation Tolerant Self-Compensation Sense Amplifier Design

As we move under the aegis of the Moore\u27s law, we have to deal with its darker side with problems like leakage and short channel effects. Once we go beyond 45nm regime process variations also have emerged as a significant design concern.Embedded memories uses sense amplifier for fast sensing and typically, sense amplifiers uses pair of matched transistors in a positive feedback environment. A small difference in voltage level of applied input signals to these matched transistors is amplified and the resulting logic signals are latched. Intra die variation causes mismatch between the sense transistors that should ideally be identical structures. Yield loss due to device and process variations has never been so critical to cause failure in circuits. Due to growth in size of embedded SRAMs as well as usage of sense amplifier based signaling techniques, process variations in sense amplifiers leads to significant loss of yield for that we need to come up with process variation tolerant circuit styles and new devices. In this work impact of transistor mismatch due to process variations on sense amplifier is evaluated and this problem is stated. For the solution of the problem a novel self compensation scheme on sense amplifiers is presented on different technology nodes up to 32nm on conventional bulk MOSFET technology. Our results show that the self compensation technique in the conventional bulk MOSFET latch type sense amplifier not just gives improvement in the yield but also leads to improvement in performance for latch type sense amplifiers. Lithography related CD variations, fluctuations in dopant density, oxide thickness and parametric variations of devices are identified as a major challenge to the classical bulk type MOSFET. With the emerging nanoscale devices, SIA roadmap identifies FinFETs as a candidate for post-planar end-of-roadmap CMOS device. With current technology scaling issues and with conventional bulk type MOSFET on 32nm node our technique can easily be applied to Double Gate devices. In this work, we also develop the model of Double Gate MOSFET through 3D Device Simulator Damocles and TCAD simulator. We propose a FinFET based process variation tolerant sense amplifier design that exploits the back gate of FinFET devices for dynamic compensation against process variations. Results from statistical simulation show that the proposed dynamic compensation is highly effective in restoring yield at a level comparable to that of sense amplifiers without process variations. We created the 32nm double gate models generated from Damocles 3-D device simulations [25] and Taurus Device Simulator available commercially from Synopsys [47] and use them in the nominal latch type sense amplifier design and on the Independent Gate Self Compensation Sense Amplifier Design (IGSSA) to compare the yield and performance benefits of sense amplifier design on FinFET technology over the conventional bulk type CMOS based sense amplifier on 32nm technology node effective in restoring yield at a level comparable to that of sense amplifiers without process variations. We created the 32nm double gate models generated from Damocles 3-D device simulations [25] and Taurus Device Simulator available commercially from Synopsys [47] and use them in the nominal latch type sense amplifier design and on the Independent Gate Self Compensation Sense Amplifier Design (IGSSA) to compare the yield and performance benefits of sense amplifier design on FinFET technology over the conventional bulk type CMOS based sense amplifier on 32nm technology node

Static random-access memory designs based on different FinFET at lower technology node (7nm)

Title from PDF of title page viewed January 15, 2020Thesis advisor: Masud H ChowdhuryVitaIncludes bibliographical references (page 50-57)Thesis (M.S.)--School of Computing and Engineering. University of Missouri--Kansas City, 2019The Static Random-Access Memory (SRAM) has a significant performance impact on current nanoelectronics systems. To improve SRAM efficiency, it is important to utilize emerging technologies to overcome short-channel effects (SCE) of conventional CMOS. FinFET devices are promising emerging devices that can be utilized to improve the performance of SRAM designs at lower technology nodes. In this thesis, I present detail analysis of SRAM cells using different types of FinFET devices at 7nm technology. From the analysis, it can be concluded that the performance of both 6T and 8T SRAM designs are improved. 6T SRAM achieves a 44.97% improvement in the read energy compared to 8T SRAM. However, 6T SRAM write energy degraded by 3.16% compared to 8T SRAM. Read stability and write ability of SRAM cells are determined using Static Noise Margin and N- curve methods. Moreover, Monte Carlo simulations are performed on the SRAM cells to evaluate process variations. Simulations were done in HSPICE using 7nm Asymmetrical Underlap FinFET technology. The quasiplanar FinFET structure gained considerable attention because of the ease of the fabrication process [1] – [4]. Scaling of technology have degraded the performance of CMOS designs because of the short channel effects (SCEs) [5], [6]. Therefore, there has been upsurge in demand for FinFET devices for emerging market segments including artificial intelligence and cloud computing (AI) [8], [9], Internet of Things (IoT) [10] – [13] and biomedical [17] –[18] which have their own exclusive style of design. In recent years, many Underlapped FinFET devices were proposed to have better control of the SCEs in the sub-nanometer technologies [3], [4], [19] – [33]. Underlap on either side of the gate increases effective channel length as seen by the charge carriers. Consequently, the source-to-drain tunneling probability is improved. Moreover, edge direct tunneling leakage components can be reduced by controlling the electric field at the gate-drain junction . There is a limitation on the extent of underlap on drain or source sides because the ION is lower for larger underlap. Additionally, FinFET based designs have major width quantization issue. The width of a FinFET device increases only in quanta of silicon fin height (HFIN) [4]. The width quantization issue becomes critical for ratioed designs like SRAMs, where proper sizing of the transistors is essential for fault-free operation. FinFETs based on Design/Technology Co-Optimization (DTCO_F) approach can overcome these issues [38]. DTCO_F follows special design rules, which provides the specifications for the standard SRAM cells with special spacing rules and low leakages. The performances of 6T SRAM designs implemented by different FinFET devices are compared for different pull-up, pull down and pass gate transistor (PU: PD:PG) ratios to identify the best FinFET device for high speed and low power SRAM applications. Underlapped FinFETs (UF) and Design/Technology Co-Optimized FinFETs (DTCO_F) are used for the design and analysis. It is observed that with the PU: PD:PG ratios of 1:1:1 and 1:5:2 for the UF-SRAMs the read energy has degraded by 3.31% and 48.72% compared to the DTCO_F-SRAMs, respectively. However, the read energy with 2:5:2 ratio has improved by 32.71% in the UF-SRAM compared to the DTCO_F-SRAMs. The write energy with 1:1:1 configuration has improved by 642.27% in the UF-SRAM compared to the DTCO_F-SRAM. On the other hand, the write energy with 1:5:2 and 2:5:2 configurations have degraded by 86.26% and 96% in the UF-SRAMs compared to the DTCO_F-SRAMs. The stability and reliability of different SRAMs are also evaluated for 500mV supply. From the analysis, it can be concluded that Asymmetrical Underlapped FinFET is better for high-speed applications and DTCO FinFET for low power applications.Introduction -- Next generation high performance device: FinFET -- FinFET based SRAM bitcell designs -- Benchmarking of UF-SRAMs and DTCO-F-SRAMS -- Collaborative project -- Internship experience at INTEL and Marvell Semiconductor -- Conclusion and future wor