Analyse und Erweiterung eines fehler-toleranten NoC für SRAM-basierte FPGAs in Weltraumapplikationen

Data Processing Units for scientific space mission need to process ever higher volumes of data and perform ever complex calculations. But the performance of available space-qualified general purpose processors is just in the lower three digit megahertz range, which is already insufficient for some applications. As an alternative, suitable processing steps can be implemented in hardware on a space-qualified SRAM-based FPGA. However, suitable devices are susceptible against space radiation. At the Institute for Communication and Network Engineering a fault-tolerant, network-based communication architecture was developed, which enables the construction of processing chains on the basis of different processing modules within suitable SRAM-based FPGAs and allows the exchange of single processing modules during runtime, too. The communication architecture and its protocol shall isolate non SEU mitigated or just partial SEU mitigated modules affected by radiation-induced faults to prohibit the propagation of errors within the remaining System-on-Chip. In the context of an ESA study, this communication architecture was extended with further components and implemented in a representative hardware platform. Based on the acquired experiences during the study, this work analyses the actual fault-tolerance characteristics as well as weak points of this initial implementation. At appropriate locations, the communication architecture was extended with mechanisms for fault-detection and fault-differentiation as well as with a hardware-based monitoring solution. Both, the former measures and the extension of the employed hardware-platform with selective fault-injection capabilities for the emulation of radiation-induced faults within critical areas of a non SEU mitigated processing module, are used to evaluate the effects of radiation-induced faults within the communication architecture. By means of the gathered results, further measures to increase fast detection and isolation of faulty nodes are developed, selectively implemented and verified. In particular, the ability of the communication architecture to isolate network nodes without SEU mitigation could be significantly improved.Instrumentenrechner für wissenschaftliche Weltraummissionen müssen ein immer höheres Datenvolumen verarbeiten und immer komplexere Berechnungen ausführen. Die Performanz von verfügbaren qualifizierten Universalprozessoren liegt aber lediglich im unteren dreistelligen Megahertz-Bereich, was für einige Anwendungen bereits nicht mehr ausreicht. Als Alternative bietet sich die Implementierung von entsprechend geeigneten Datenverarbeitungsschritten in Hardware auf einem qualifizierten SRAM-basierten FPGA an. Geeignete Bausteine sind jedoch empfindlich gegenüber der Strahlungsumgebung im Weltraum. Am Institut für Datentechnik und Kommunikationsnetze wurde eine fehlertolerante netzwerk-basierte Kommunikationsarchitektur entwickelt, die innerhalb eines geeigneten SRAM-basierten FPGAs Datenverarbeitungsmodule miteinander nach Bedarf zu Verarbeitungsketten verbindet, sowie den Austausch von einzelnen Modulen im Betrieb ermöglicht. Nicht oder nur partiell SEU mitigierte Module sollen bei strahlungsbedingten Fehlern im Modul durch das Protokoll und die Fehlererkennungsmechanismen der Kommunikationsarchitektur isoliert werden, um ein Ausbreiten des Fehlers im restlichen System-on-Chip zu verhindern. Im Kontext einer ESA Studie wurde diese Kommunikationsarchitektur um Komponenten erweitert und auf einer repräsentativen Hardwareplattform umgesetzt. Basierend auf den gesammelten Erfahrungen aus der Studie, wird in dieser Arbeit eine Analyse der tatsächlichen Fehlertoleranz-Eigenschaften sowie der Schwachstellen dieser ursprünglichen Implementierung durchgeführt. Die Kommunikationsarchitektur wurde an geeigneten Stellen um Fehlerdetektierungs- und Fehlerunterscheidungsmöglichkeiten erweitert, sowie um eine hardwarebasierte Überwachung ergänzt. Sowohl diese Maßnahmen, als auch die Erweiterung der Hardwareplattform um gezielte Fehlerinjektions-Möglichkeiten zum Emulieren von strahlungsinduzierten Fehlern in kritischen Komponenten eines nicht SEU mitigierten Prozessierungsmoduls werden genutzt, um die tatsächlichen auftretenden Effekte in der Kommunikationsarchitektur zu evaluieren. Anhand der Ergebnisse werden weitere Verbesserungsmaßnahmen speziell zur schnellen Detektierung und Isolation von fehlerhaften Knoten erarbeitet, selektiv implementiert und verifiziert. Insbesondere die Fähigkeit, fehlerhafte, nicht SEU mitigierte Netzwerkknoten innerhalb der Kommunikationsarchitektur zu isolieren, konnte dabei deutlich verbessert werden

Bioinformatics

This book is divided into different research areas relevant in Bioinformatics such as biological networks, next generation sequencing, high performance computing, molecular modeling, structural bioinformatics, molecular modeling and intelligent data analysis. Each book section introduces the basic concepts and then explains its application to problems of great relevance, so both novice and expert readers can benefit from the information and research works presented here

A Practical Investigation into Achieving Bio-Plausibility in Evo-Devo Neural Microcircuits Feasible in an FPGA

Many researchers has conjectured, argued, or in some cases demonstrated, that bio-plausibility can bring about emergent properties such as adaptability, scalability, fault-tolerance, self-repair, reliability, and autonomy to bio-inspired intelligent systems. Evolutionary-developmental (evo-devo) spiking neural networks are a very bio-plausible mixture of such bio-inspired intelligent systems that have been proposed and studied by a few researchers. However, the general trend is that the complexity and thus the computational cost grow with the bio-plausibility of the system. FPGAs (Field- Programmable Gate Arrays) have been used and proved to be one of the flexible and cost efficient hardware platforms for research' and development of such evo-devo systems. However, mapping a bio-plausible evo-devo spiking neural network to an FPGA is a daunting task full of different constraints and trade-offs that makes it, if not infeasible, very challenging. This thesis explores the challenges, trade-offs, constraints, practical issues, and some possible approaches in achieving bio-plausibility in creating evolutionary developmental spiking neural microcircuits in an FPGA through a practical investigation along with a series of case studies. In this study, the system performance, cost, reliability, scalability, availability, and design and testing time and complexity are defined as measures for feasibility of a system and structural accuracy and consistency with the current knowledge in biology as measures for bio-plausibility. Investigation of the challenges starts with the hardware platform selection and then neuron, cortex, and evo-devo models and integration of these models into a whole bio-inspired intelligent system are examined one by one. For further practical investigation, a new PLAQIF Digital Neuron model, a novel Cortex model, and a new multicellular LGRN evo-devo model are designed, implemented and tested as case studies. Results and their implications for the researchers, designers of such systems, and FPGA manufacturers are discussed and concluded in form of general trends, trade-offs, suggestions, and recommendations

Soft Error Resistant Design of the AES Cipher Using SRAM-based FPGA

This thesis presents a new architecture for the reliable implementation of the symmetric-key algorithm Advanced Encryption Standard (AES) in Field Programmable Gate Arrays (FPGAs). Since FPGAs are prone to soft errors caused by radiation, and AES is highly sensitive to errors, reliable architectures are of significant concern. Energetic particles hitting a device can flip bits in FPGA SRAM cells controlling all aspects of the implementation. Unlike previous research, heterogeneous error detection techniques based on properties of the circuit and functionality are used to provide adequate reliability at the lowest possible cost. The use of dual ported block memory for SubBytes, duplication for the control circuitry, and a new enhanced parity technique for MixColumns is proposed. Previous parity techniques cover single errors in datapath registers, however, soft errors can occur in the control circuitry as well as in SRAM cells forming the combinational logic and routing. In this research, propagation of single errors is investigated in the routed netlist. Weaknesses of the previous parity techniques are identified. Architectural redesign at the register-transfer level is introduced to resolve undetected single errors in both the routing and the combinational logic. Reliability of the AES implementation is not only a critical issue in large scale FPGA-based systems but also at both higher altitudes and in space applications where there are a larger number of energetic particles. Thus, this research is important for providing efficient soft error resistant design in many current and future secure applications

Real-time trace decoding and monitoring for safety and security in embedded systems

Integrated circuits and systems can be found almost everywhere in today’s world. As their use increases, they need to be made safer and more perfor mant to meet current demands in processing power. FPGA integrated SoCs can provide the ideal trade-off between performance, adaptability, and energy usage. One of today’s vital challenges lies in updating existing fault tolerance techniques for these new systems while utilizing all available processing capa bilities, such as multi-core and heterogeneous processing units. Control-flow monitoring is one of the primary mechanisms described for error detection at the software architectural level for the highest grade of hazard level clas sifications (e.g., ASIL D) described in industry safety standards ISO-26262. Control-flow errors are also known to compose the majority of detected errors for ICs and embedded systems in safety-critical and risk-susceptible environ ments [5]. Software-based monitoring methods remain the most popular [6–8]. However, recent studies show that the overheads they impose make actual reliability gains negligible [9, 10]. This work proposes and demonstrates a new control flow checking method implemented in FPGA for multi-core embedded systems called control-flow trace checker (CFTC). CFTC uses existing trace and debug subsystems of modern processors to rebuild their execution states. It can iden tify any errors in real-time by comparing executed states to a set of permitted state transitions determined statically. This novel implementation weighs hardware resource trade-offs to target mul tiple independent tasks in multi-core embedded applications, as well as single core systems. The proposed system is entirely implemented in hardware and isolated from all monitored software components, requiring 2.4% of the target FPGA platform resources to protect an execution unit in its entirety. There fore, it avoids undesired overheads and maintains deterministic error detection latencies, which guarantees reliability improvements without impairing the target software system. Finally, CFTC is evaluated under different software i Resumo fault-injection scenarios, achieving detection rates of 100% of all control-flow errors to wrong destinations and 98% of all injected faults to program binaries. All detection times are further analyzed and precisely described by a model based on the monitor’s resources and speed and the software application’s control-flow structure and binary characteristics.Circuitos integrados estão presentes em quase todos sistemas complexos do mundo moderno. Conforme sua frequência de uso aumenta, eles precisam se tornar mais seguros e performantes para conseguir atender as novas demandas em potência de processamento. Sistemas em Chip integrados com FPGAs conseguem prover o balanço perfeito entre desempenho, adaptabilidade, e uso de energia. Um dos maiores desafios agora é a necessidade de atualizar técnicas de tolerância à falhas para estes novos sistemas, aproveitando os novos avanços em capacidade de processamento. Monitoramento de fluxo de controle é um dos principais mecanismos para a detecção de erros em nível de software para sistemas classificados como de alto risco (e.g. ASIL D), descrito em padrões de segurança como o ISO-26262. Estes erros são conhecidos por compor a maioria dos erros detectados em sistemas integrados [5]. Embora métodos de monitoramento baseados em software continuem sendo os mais populares [6–8], estudos recentes mostram que seus custos adicionais, em termos de performance e área, diminuem consideravelmente seus ganhos reais em confiabilidade [9, 10]. Propomos aqui um novo método de monitora mento de fluxo de controle implementado em FPGA para sistemas embarcados multi-core. Este método usa subsistemas de trace e execução de código para reconstruir o estado atual do processador, identificando erros através de com parações entre diferentes estados de execução da CPU. Propomos uma implementação que considera trade-offs no uso de recuros de sistema para monitorar múltiplas tarefas independetes. Nossa abordagem suporta o monitoramento de sistemas simples e também de sistemas multi-core multitarefa. Por fim, nossa técnica é totalmente implementada em hardware, evitando o uso de unidades de processamento de software que possa adicionar custos indesejáveis à aplicação em perda de confiabilidade. Propomos, assim, um mecanismo de verificação de fluxo de controle, escalável e extensível, para proteção de sistemas embarcados críticos e multi-core

Real-Time Trace Decoding and Monitoring for Safety and Security in Embedded Systems

Integrated circuits and systems can be found almost everywhere in today’s world. As their use increases, they need to be made safer and more perfor mant to meet current demands in processing power. FPGA integrated SoCs can provide the ideal trade-off between performance, adaptability, and energy usage. One of today’s vital challenges lies in updating existing fault tolerance techniques for these new systems while utilizing all available processing capa bilities, such as multi-core and heterogeneous processing units. Control-flow monitoring is one of the primary mechanisms described for error detection at the software architectural level for the highest grade of hazard level clas sifications (e.g., ASIL D) described in industry safety standards ISO-26262. Control-flow errors are also known to compose the majority of detected errors for ICs and embedded systems in safety-critical and risk-susceptible environ ments [5]. Software-based monitoring methods remain the most popular [6–8]. However, recent studies show that the overheads they impose make actual reliability gains negligible [9, 10]. This work proposes and demonstrates a new control flow checking method implemented in FPGA for multi-core embedded systems called control-flow trace checker (CFTC). CFTC uses existing trace and debug subsystems of modern processors to rebuild their execution states. It can iden tify any errors in real-time by comparing executed states to a set of permitted state transitions determined statically. This novel implementation weighs hardware resource trade-offs to target mul tiple independent tasks in multi-core embedded applications, as well as single core systems. The proposed system is entirely implemented in hardware and isolated from all monitored software components, requiring 2.4% of the target FPGA platform resources to protect an execution unit in its entirety. There fore, it avoids undesired overheads and maintains deterministic error detection latencies, which guarantees reliability improvements without impairing the target software system. Finally, CFTC is evaluated under different software i Resumo fault-injection scenarios, achieving detection rates of 100% of all control-flow errors to wrong destinations and 98% of all injected faults to program binaries. All detection times are further analyzed and precisely described by a model based on the monitor’s resources and speed and the software application’s control-flow structure and binary characteristics.Circuitos integrados estão presentes em quase todos sistemas complexos do mundo moderno. Conforme sua frequência de uso aumenta, eles precisam se tornar mais seguros e performantes para conseguir atender as novas demandas em potência de processamento. Sistemas em Chip integrados com FPGAs conseguem prover o balanço perfeito entre desempenho, adaptabilidade, e uso de energia. Um dos maiores desafios agora é a necessidade de atualizar técnicas de tolerância à falhas para estes novos sistemas, aproveitando os novos avanços em capacidade de processamento. Monitoramento de fluxo de controle é um dos principais mecanismos para a detecção de erros em nível de software para sistemas classificados como de alto risco (e.g. ASIL D), descrito em padrões de segurança como o ISO-26262. Estes erros são conhecidos por compor a maioria dos erros detectados em sistemas integrados [5]. Embora métodos de monitoramento baseados em software continuem sendo os mais populares [6–8], estudos recentes mostram que seus custos adicionais, em termos de performance e área, diminuem consideravelmente seus ganhos reais em confiabilidade [9, 10]. Propomos aqui um novo método de monitora mento de fluxo de controle implementado em FPGA para sistemas embarcados multi-core. Este método usa subsistemas de trace e execução de código para reconstruir o estado atual do processador, identificando erros através de com parações entre diferentes estados de execução da CPU. Propomos uma implementação que considera trade-offs no uso de recuros de sistema para monitorar múltiplas tarefas independetes. Nossa abordagem suporta o monitoramento de sistemas simples e também de sistemas multi-core multitarefa. Por fim, nossa técnica é totalmente implementada em hardware, evitando o uso de unidades de processamento de software que possa adicionar custos indesejáveis à aplicação em perda de confiabilidade. Propomos, assim, um mecanismo de verificação de fluxo de controle, escalável e extensível, para proteção de sistemas embarcados críticos e multi-core

Advanced information processing system: The Army fault tolerant architecture conceptual study. Volume 2: Army fault tolerant architecture design and analysis

Described here is the Army Fault Tolerant Architecture (AFTA) hardware architecture and components and the operating system. The architectural and operational theory of the AFTA Fault Tolerant Data Bus is discussed. The test and maintenance strategy developed for use in fielded AFTA installations is presented. An approach to be used in reducing the probability of AFTA failure due to common mode faults is described. Analytical models for AFTA performance, reliability, availability, life cycle cost, weight, power, and volume are developed. An approach is presented for using VHSIC Hardware Description Language (VHDL) to describe and design AFTA's developmental hardware. A plan is described for verifying and validating key AFTA concepts during the Dem/Val phase. Analytical models and partial mission requirements are used to generate AFTA configurations for the TF/TA/NOE and Ground Vehicle missions