Stabilizing control for power converters connected to transmission lines

This paper proposes a switching control strategy for the set-point stabilization of a power converter connected via a transmission line to a resistive load. The strategy employs a Lyapunov function that is directly based on energy considerations of the power converter, as well as of the transmission line described by the telegraph equations. The proposed stabilizing switching control still allows a certain freedom in the choice of the control law, a comparison between a maximum descent strategy and a minimum commutation strategy being discussed on a simple example.

Nonlinear Analysis and Control of Interleaved Boost Converter Using Real-Time Cycle to Cycle Variable Slope Compensation

Switched-mode power converters are inherently nonlinear and piecewise smooth systems that may exhibit a series of undesirable operations that can greatly reduce the converter's efficiency and lifetime. This paper presents a nonlinear analysis technique to investigate the influence of system parameters on the stability of interleaved boost converters. In this approach, Monodromy matrix that contains all the comprehensive information of converter parameters and control loop can be employed to fully reveal and understand the inherent nonlinear dynamics of interleaved boost converters, including the interaction effect of switching operation. Thereby not only the boundary conditions but also the relationship between stability margin and the parameters given can be intuitively studied by the eigenvalues of this matrix. Furthermore, by employing the knowledge gained from this analysis, a real-Time cycle to cycle variable slope compensation method is proposed to guarantee a satisfactory performance of the converter with an extended range of stable operation. Outcomes show that systems can regain stability by applying the proposed method within a few time periods of switching cycles. The numerical and analytical results validate the theoretical analysis, and experimental results verify the effectiveness of the proposed approach

An improved closed loop hybrid phase shift controller for dual active bridge converter

In this paper, a new closed loop hybrid phase shift control is proposed for dual active bridge (DAB) converter with variable input voltage. The extended phase shift (EPS) control is applied when load gets heavy enough and the secondary side phase shift angle decreases to zero. When this modified DAB converter operates at light loads, the triple phase shift (TPS) modulation method is applied, and the added control freedom is the secondary phase shift angle between the two-secondary side switching legs. The hybrid phase shift control (HPS) scheme is a combination of EPS and TPS modulations, and it provides a very simple closed form implementation for the primary and secondary side phase shift angles. Depending on the application by changing the phase shift angles we can achieve Buck or Boost operation. A characteristic table feedback control method has been used for closed loop operation. By using 1D look up table the proposed DAB converter provides constant 400V for any given input voltage

An Optimized Hybrid Modulation Scheme for Reducing Conduction Losses in Dual Active Bridge Converters

A linearized hybrid modulation scheme for the dual active bridge (DAB) converter is proposed in this article. For the purpose of minimizing the conduction losses dissipated on the transformer and the power transistors, an optimal relationship function between the two control variables employed in extended phase shift (EPS) modulation can be derived. However, the obtained relationship function is a complex expression, which is not good for simple on-line control. Hence, a linearized modulation scheme is proposed in this article. This modulation scheme can achieve a quasi-minimum root-mean-square (rms) value of the leakage inductance current for the same output power. Meanwhile, the zero-voltage switching (ZVS) of the power transistors can be achieved over the whole power range. The power transfer capability is also kept the same as the optimal EPS scheme. Finally, experiments are conducted on a laboratory prototype to validate the effect of the linearized modulation scheme on the reduction of conduction losses. The experimental results present an improved converter efficiency and the realization of ZVS.</p

Design of High-Gain DC-DC Converters for High-Power PV Applications

Renewable energy sources are penetrating the market in an ever increasing rate, especially in terms of Wind and Solar energies, with the latter being more suitable for the GCC region. Typically, Photovoltaic (PV) strings’ output voltage is limited to ~ 1500 V due to safety constraints, and thus requires boosting to higher DC levels (non-isolated step-up DC-DC transformer) suitable for High-Voltage DC (HVDC) and AC grid applications in order to provide the required DC-Link voltage level. Nevertheless, conventional non-isolated DC-DC converters provide a limited practical gain due to their parasitic elements. Other options include isolated DC-DC converters that utilize costly high-frequency transformers with limited power capability. Moreover, the isolation requirements of transformers in HVDC significantly increase the footprint of the converters. High-frequency transformers for high-power applications are hard to design and are usually associated with higher losses. Alternatively, connecting conventional DC-DC converters in different combinations can provide higher gains to the required levels, while maintaining the high efficiency requirements. This thesis proposes the cascade and/or series connection of DC-DC modules as a solution to the high-conversion ratio requirement, based on Cuk and Single-Ended Primary Inductor Converter (SEPIC) topologies, whose continuous input current is suitable for PV applications, and reduces the bulky capacitor filters at the input side. Detailed theoretical models of the proposed topologies are first derived, then their trends are practically verified by low power prototypes. Sensitivity analysis is also performed to assess the effect of small variations to the parasitic inductors’ resistances on the overall system gain, where the input inductor is found to have a considerable effect, especially at higher duty ratios (i.e. higher gains). High-power applications’ scenarios with their considerations are simulated to compare the different topologies and the results show a comparable efficiency of the proposed converters for a 1 –MW application with efficiencies higher than 90%

Polynomial Curve Slope Compensation for Peak-Current-Mode-Controlled Power Converters

Linear ramp slope compensation (LRC) and quadratic slope compensation (QSC) are commonly implemented in peak-current-mode-controlled dc-dc converters in order to minimize subharmonic and chaotic oscillations. Both compensating schemes rely on the linearized state-space averaged model (LSSA) of the converter. The LSSA ignores the impact that switching actions have on the stability of converters. In order to include switching events, the nonlinear analysis method based on the Monodromy matrix was introduced to describe a complete-cycle stability. Analyses on analog-controlled dc-dc converters applying this method show that system stability is strongly dependent on the change of the derivative of the slope at the time of switching instant. However, in a mixed-signal-controlled system, the digitalization effect contributes differently to system stability. This paper shows a full complete-cycle stability analysis using this nonlinear analysis method, which is applied to a mixed-signal-controlled converter. Through this analysis, a generalized equation is derived that reveals for the first time the real boundary stability limits for LRC and QSC. Furthermore, this generalized equation allows the design of a new compensating scheme, which is able to increase system stability. The proposed scheme is called polynomial curve slope compensation (PCSC) and it is demonstrated that PCSC increases the stable margin by 30% compared to LRC and 20% to QSC. This outcome is proved experimentally by using an interleaved dc-dc converter that is built for this work

Survey on Photo-Voltaic Powered Interleaved Converter System

Renewable energy is the best solution to meet the growing demand for energy in the country. The solar energy is considered as the most promising energy by the researchers due to its abundant availability, eco-friendly nature, long lasting nature, wide range of application and above all it is a maintenance free system. The energy absorbed by the earth can satisfy 15000 times of today’s total energy demand and its hundred times more than that our conventional energy like coal and other fossil fuels. Though, there are overwhelming advantages in solar energy, It has few drawbacks as well such as its low conversion ratio, inconsistent supply of energy due to variation in the sun light, less efficiency due to ripples in the converter, time dependent and, above all, high capitation cost. These aforementioned flaws have been addressed by the researchers in order to extract maximum energy and attain hundred percentage benefits of this heavenly resource. So, this chapter presents a comprehensive investigation based on photo voltaic (PV) system requirements with the following constraints such as system efficiency, system gain, dynamic response, switching losses are investigated. The overview exhibits and identifies the requirements of a best PV power generation system

Isolated Single-stage Power Electronic Building Blocks Using Medium Voltage Series-stacked Wide-bandgap Switches

The demand for efficient power conversion systems that can process the energy at high power and voltage levels is increasing every day. These systems are to be used in microgrid applications. Wide-bandgap semiconductor devices (i.e. Silicon Carbide (SiC) and Gallium Nitride (GaN) devices) are very promising candidates due to their lower conduction and switching losses compared to the state-of-the-art Silicon (Si) devices. The main challenge for these devices is that their breakdown voltages are relatively lower compared to their Si counterpart. In addition, the high frequency operation of the wide-bandgap devices are impeded in many cases by the magnetic core losses of the magnetic coupling components (i.e. coupled inductors and/or high frequency transformers) utilized in the power converter circuit. Six new dc-dc converter topologies are propose. The converters have reduced voltage stresses on the switches. Three of them are unidirectional step-up converters with universal input voltage which make them excellent candidates for photovoltaic and fuel cell applications. The other three converters are bidirectional dc-dc converters with wide voltage conversion ratios. These converters are very good candidates for the applications that require bidirectional power flow capability. In addition, the wide voltage conversion ratios of these converters can be utilized for applications such as energy storage systems with wide voltage swings

Derivation of new double-input DC-DC converters using the building block methodology

In most power electronic systems, the instantaneous input and output power vary by time and are not exactly identical with each other. Hence, providing a good match between them is a complicated task to deal with if not impossible. Furthermore, due to the wide variation range of the processed power, the overall efficiency of the system is not high. The solution is to hybridize the system using an energy storage unit like in hybrid electric vehicles, power factor correction systems, and photovoltaic systems. Multi-input converters play a key role in such hybridized systems, where it is required to have more than one power source...In this thesis, a systematic approach to derive several new double-input converters using H-bridge cells or single-pole triple-throw switches as building blocks is proposed. Different operating modes and the switch realization of the new converters are obtained and their corresponding voltage ratios are derived. Bidirectional power flow is also considered. All of the proposed converters consist of only one inductor; hence, the number of passive elements that are required is reduced. The operating characteristics of the new converters are verified using simulation results --Abstract, page iii