Low-cost, multi-agent systems for planetary surface exploration

The use of off-the-shelf consumer electronics combined with top-down design methodologies have made small and inexpensive satellites, such as CubeSats, emerge as viable, low-cost and attractive space-based platforms that enable a range of new and exciting mission scenarios. In addition, to overcome some of the resource limitation issues encountered with these platforms, distributed architectures have emerged to enable complex tasks through the use of multiple low complexity units. The low-cost characteristics of such systems coupled with the distributed architecture allows for an increase in the size of the system beyond what would have been feasible with a monolithic system, hence widening the operational capabilities without significantly increasing the control complexity of the system. These ideas are not new for Earth orbiting devices, but excluding some distributed remote sensing architectures they are yet to be applied for the purpose of planetary exploration. Experience gained through large rovers demonstrates the value of in-situ exploration, which is however limited by the associated high-cost and risk. The loss of a rover can and has happened because of a number of possible failures: besides the hazards directly linked to the launch and journey to the target-body, hard landing and malfunctioning of parts are all threats to the success of the mission. To overcome these issues this paper introduces the concept of using off-the-shelf consumer electronics to deploy a low-cost multi-rover system for future planetary surface exploration. It is shown that such a system would significantly reduce the programmatic-risk of the mission (for example catastrophic failure of a single rover), while exploiting the inherent advantages of cooperative behaviour. These advantages are analysed with a particular emphasis put upon the guidance, navigation and control of such architectures using the method of artificial potential field. Laboratory tests on multi-agent robotic systems support the analysis. Principal features of the system are identified and the underlying advantages over a monolithic single-agent system highlighted

Efficient and secure real-time mobile robots cooperation using visual servoing

This paper deals with the challenging problem of navigation in formation of mobiles robots fleet. For that purpose, a secure approach is used based on visual servoing to control velocities (linear and angular) of the multiple robots. To construct our system, we develop the interaction matrix which combines the moments in the image with robots velocities and we estimate the depth between each robot and the targeted object. This is done without any communication between the robots which eliminate the problem of the influence of each robot errors on the whole. For a successful visual servoing, we propose a powerful mechanism to execute safely the robots navigation, exploiting a robot accident reporting system using raspberry Pi3. In addition, in case of problem, a robot accident detection reporting system testbed is used to send an accident notification, in the form of a specifical message. Experimental results are presented using nonholonomic mobiles robots with on-board real time cameras, to show the effectiveness of the proposed method

Visual servoing of mobile robots using non-central catadioptric cameras

This paper presents novel contributions on image-based control of a mobile robot using a general catadioptric camera model. A catadioptric camera is usually made up by a combination of a conventional camera and a curved mirror resulting in an omnidirectional sensor capable of providing 360° panoramic views of a scene. Modeling such cameras has been the subject of significant research interest in the computer vision community leading to a deeper understanding of the image properties and also to different models for different types of configurations. Visual servoing applications using catadioptric cameras have essentially been using central cameras and the corresponding unified projection model. So far only in a few cases more general models have been used. In this paper we address the problem of visual servoing using the so-called radial model. The radial model can be applied to many camera configurations and in particular to non-central catadioptric systems with mirrors that are symmetric around an axis coinciding with the optical axis. In this case, we show that the radial model can be used with a non-central catadioptric camera to allow effective image-based visual servoing (IBVS) of a mobile robot. Using this model, which is valid for a large set of catadioptric cameras (central or non-central), new visual features are proposed to control the degrees of freedom of a mobile robot moving on a plane. In addition to several simulation results, a set of experiments was carried out on Robot Operating System (ROS)-based platform which validates the applicability, effectiveness and robustness of the proposed method for image-based control of a non-holonomic robot

A Benchmarking of DCM Based Architectures for Position and Velocity Controlled Walking of Humanoid Robots

This paper contributes towards the development and comparison of Divergent-Component-of-Motion (DCM) based control architectures for humanoid robot locomotion. More precisely, we present and compare several DCM based implementations of a three layer control architecture. From top to bottom, these three layers are here called: trajectory optimization, simplified model control, and whole-body QP control. All layers use the DCM concept to generate references for the layer below. For the simplified model control layer, we present and compare both instantaneous and Receding Horizon Control controllers. For the whole-body QP control layer, we present and compare controllers for position and velocity control robots. Experimental results are carried out on the one-meter tall iCub humanoid robot. We show which implementation of the above control architecture allows the robot to achieve a walking velocity of 0.41 meters per second.Comment: Submitted to Humanoids201

Safe, Remote-Access Swarm Robotics Research on the Robotarium

This paper describes the development of the Robotarium -- a remotely accessible, multi-robot research facility. The impetus behind the Robotarium is that multi-robot testbeds constitute an integral and essential part of the multi-agent research cycle, yet they are expensive, complex, and time-consuming to develop, operate, and maintain. These resource constraints, in turn, limit access for large groups of researchers and students, which is what the Robotarium is remedying by providing users with remote access to a state-of-the-art multi-robot test facility. This paper details the design and operation of the Robotarium as well as connects these to the particular considerations one must take when making complex hardware remotely accessible. In particular, safety must be built in already at the design phase without overly constraining which coordinated control programs the users can upload and execute, which calls for minimally invasive safety routines with provable performance guarantees.Comment: 13 pages, 7 figures, 3 code samples, 72 reference

A Framework for Collaborative Multi-task, Multi-robot Missions

Robotics is a transformative technology that will empower our civilization for a new scale of human endeavors. Massive scale is only possible through the collaboration of individual or groups of robots. Collaboration allows specialization, meaning a multirobot system may accommodate heterogeneous platforms including human partners. This work develops a unified control architecture for collaborative missions comprised of multiple, multi-robot tasks. Using kinematic equations and Jacobian matrices, the system states are transformed into alternative control spaces which are more useful for the designer or more convenient for the operator. The architecture allows multiple tasks to be combined, composing tightly coordinated missions. Using this approach, the designer is able to compensate for non-ideal behavior in the appropriate space using whatever control scheme they choose. This work presents a general design methodology, including analysis techniques for relevant control metrics like stability, responsiveness, and disturbance rejection, which were missing in prior work. Multiple tasks may be combined into a collaborative mission. The unified motion control architecture merges the control space components for each task into a concise federated system to facilitate analysis and implementation. The task coordination function defines task commands as functions of mission commands and state values to create explicit closed-loop collaboration. This work presents analysis techniques to understand the effects of cross-coupling tasks. This work analyzes system stability for the particular control architecture and identifies an explicit condition to ensure stable switching when reallocating robots. We are unaware of any other automated control architectures that address large-scale collaborative systems composed of task-oriented multi-robot coalitions where relative spatial control is critical to mission performance. This architecture and methodology have been validated in experiments and in simulations, repeating earlier work and exploring new scenarios and. It can perform large-scale, complex missions via a rigorous design methodology

Cooperative Material Handling by Human and Robotic Agents:Module Development and System Synthesis

In this paper we present the results of a collaborative effort to design and implement a system for cooperative material handling by a small team of human and robotic agents in an unstructured indoor environment. Our approach makes fundamental use of human agents\u27 expertise for aspects of task planning, task monitoring, and error recovery. Our system is neither fully autonomous nor fully teleoperated. It is designed to make effective use of human abilities within the present state of the art of autonomous systems. It is designed to allow for and promote cooperative interaction between distributed agents with various capabilities and resources. Our robotic agents refer to systems which are each equipped with at least one sensing modality and which possess some capability for self-orientation and/or mobility. Our robotic agents are not required to be homogeneous with respect to either capabilities or function. Our research stresses both paradigms and testbed experimentation. Theory issues include the requisite coordination principles and techniques which are fundamental to the basic functioning of such a cooperative multi-agent system. We have constructed a testbed facility for experimenting with distributed multi-agent architectures. The required modular components of this testbed are currently operational and have been tested individually. Our current research focuses on the integration of agents in a scenario for cooperative material handling