2,150 research outputs found
An Energy and Performance Exploration of Network-on-Chip Architectures
In this paper, we explore the designs of a circuit-switched router, a wormhole router, a quality-of-service (QoS) supporting virtual channel router and a speculative virtual channel router and accurately evaluate the energy-performance tradeoffs they offer. Power results from the designs placed and routed in a 90-nm CMOS process show that all the architectures dissipate significant idle state power. The additional energy required to route a packet through the router is then shown to be dominated by the data path. This leads to the key result that, if this trend continues, the use of more elaborate control can be justified and will not be immediately limited by the energy budget. A performance analysis also shows that dynamic resource allocation leads to the lowest network latencies, while static allocation may be used to meet QoS goals. Combining the power and performance figures then allows an energy-latency product to be calculated to judge the efficiency of each of the networks. The speculative virtual channel router was shown to have a very similar efficiency to the wormhole router, while providing a better performance, supporting its use for general purpose designs. Finally, area metrics are also presented to allow a comparison of implementation costs
Recommended from our members
On Multicast in Asynchronous Networks-on-Chip: Techniques, Architectures, and FPGA Implementation
In this era of exascale computing, conventional synchronous design techniques are facing unprecedented challenges. The consumer electronics market is replete with many-core systems in the range of 16 cores to thousands of cores on chip, integrating multi-billion transistors. However, with this ever increasing complexity, the traditional design approaches are facing key issues such as increasing chip power, process variability, aging, thermal problems, and scalability. An alternative paradigm that has gained significant interest in the last decade is asynchronous design. Asynchronous designs have several potential advantages: they are naturally energy proportional, burning power only when active, do not require complex clock distribution, are robust to different forms of variability, and provide ease of composability for heterogeneous platforms. Networks-on-chip (NoCs) is an interconnect paradigm that has been introduced to deal with the ever-increasing system complexity. NoCs provide a distributed, scalable, and efficient interconnect solution for todayâs many-core systems. Moreover, NoCs are a natural match with asynchronous design techniques, as they separate communication infrastructure and timing from the computational elements. To this end, globally-asynchronous locally-synchronous (GALS) systems that interconnect multiple processing cores, operating at different clock speeds, using an asynchronous NoC, have gained significant interest. While asynchronous NoCs have several advantages, they also face a key challenge of supporting new types of traffic patterns. Once such pattern is multicast communication, where a source sends packets to arbitrary number of destinations. Multicast is not only common in parallel computing, such as for cache coherency, but also for emerging areas such as neuromorphic computing. This important capability has been largely missing from asynchronous NoCs. This thesis introduces several efficient multicast solutions for these interconnects. In particular, techniques, and network architectures are introduced to support high-performance and low-power multicast. Two leading network topologies are the focus: a variant mesh-of-trees (MoT) and a 2D mesh. In addition, for a more realistic implementation and analysis, as well as significantly advancing the field of asynchronous NoCs, this thesis also targets synthesis of these NoCs on commercial FPGAs. While there has been significant advances in FPGA technologies, there has been only limited research on implementing asynchronous NoCs on FPGAs. To this end, a systematic computeraided design (CAD) methodology has been introduced to efficiently and safely map asynchronous NoCs on FPGAs. Overall, this thesis makes the following three contributions. The first contribution is a multicast solution for a variant MoT network topology. This topology consists of simple low-radix switches, and has been used in high-performance computing platforms. A novel local speculation technique is introduced, where a subset of the networkâs switches are speculative that always broadcast every packet. These switches are very simple and have high performance. Speculative switches are surrounded by non-speculative ones that route packets based on their destinations and also throttle any redundant copies created by the former. This hybrid network architecture achieved significant performance and power benefits over other multicast approaches. The second contribution is a multicast solution for a 2D-mesh topology, which is more complex with higher-radix switches and also is more commonly used. A novel continuous-time replication strategy is introduced to optimize the critical multi-way forking operation of a multicast transmission. In this technique, a multicast packet is first stored in an input port of a switch, from where it is sent through distinct output ports towards different destinations concurrently, at each outputâs own rate and in continuous time. This strategy is shown to have significant latency and energy benefits over an approach that performs multicast using multiple distinct serial unicasts to each destination. Finally, a systematic CAD methodology is introduced to synthesize asynchronous NoCs on commercial FPGAs. A two-fold goal is targeted: correctness and high performance. For ease of implementation, only existing FPGA synthesis tools are used. Moreover, since asynchronous NoCs involve special asynchronous components, a comprehensive guide is introduced to map these elements correctly and efficiently. Two asynchronous NoC switches are synthesized using the proposed approach on a leading Xilinx FPGA in 28 nm: one that only handles unicast, and the other that also supports multicast. Both showed significant energy benefits with some performance gains over a state-of-the-art synchronous switch
Scalability of broadcast performance in wireless network-on-chip
Networks-on-Chip (NoCs) are currently the paradigm of choice to interconnect the cores of a chip multiprocessor. However, conventional NoCs may not suffice to fulfill the on-chip communication requirements of processors with hundreds or thousands of cores. The main reason is that the performance of such networks drops as the number of cores grows, especially in the presence of multicast and broadcast traffic. This not only limits the scalability of current multiprocessor architectures, but also sets a performance wall that prevents the development of architectures that generate moderate-to-high levels of multicast. In this paper, a Wireless Network-on-Chip (WNoC) where all cores share a single broadband channel is presented. Such design is conceived to provide low latency and ordered delivery for multicast/broadcast traffic, in an attempt to complement a wireline NoC that will transport the rest of communication flows. To assess the feasibility of this approach, the network performance of WNoC is analyzed as a function of the system size and the channel capacity, and then compared to that of wireline NoCs with embedded multicast support. Based on this evaluation, preliminary results on the potential performance of the proposed hybrid scheme are provided, together with guidelines for the design of MAC protocols for WNoC.Peer ReviewedPostprint (published version
The Design of a System Architecture for Mobile Multimedia Computers
This chapter discusses the system architecture of a portable computer, called Mobile Digital Companion, which provides support for handling multimedia applications energy efficiently. Because battery life is limited and battery weight is an important factor for the size and the weight of the Mobile Digital Companion, energy management plays a crucial role in the architecture. As the Companion must remain usable in a variety of environments, it has to be flexible and adaptable to various operating conditions. The Mobile Digital Companion has an unconventional architecture that saves energy by using system decomposition at different levels of the architecture and exploits locality of reference with dedicated, optimised modules. The approach is based on dedicated functionality and the extensive use of energy reduction techniques at all levels of system design. The system has an architecture with a general-purpose processor accompanied by a set of heterogeneous autonomous programmable modules, each providing an energy efficient implementation of dedicated tasks. A reconfigurable internal communication network switch exploits locality of reference and eliminates wasteful data copies
Automated Hardware Prototyping for 3D Network on Chips
Vor mehr als 50 Jahren stellte IntelÂź MitbegrĂŒnder Gordon Moore eine Prognose zum Entwicklungsprozess der Transistortechnologie auf. Er prognostizierte, dass sich die Zahl der Transistoren in integrierten Schaltungen alle zwei Jahre verdoppeln wird. Seine Aussage ist immer noch gĂŒltig, aber ein Ende von Moores Gesetz ist in Sicht. Mit dem Ende von Mooreâs Gesetz mĂŒssen neue Aspekte untersucht werden, um weiterhin die Leistung von integrierten Schaltungen zu steigern. Zwei mögliche AnsĂ€tze fĂŒr "More than Mooreâ sind 3D-Integrationsverfahren und heterogene Systeme. Gleichzeitig entwickelt sich ein Trend hin zu Multi-Core Prozessoren, basierend auf Networks on chips (NoCs).
Neben dem Ende des Mooreschen Gesetzes ergeben sich bei immer kleiner werdenden TechnologiegröĂen, vor allem jenseits der 60 nm, neue Herausforderungen. Eine Schwierigkeit ist die WĂ€rmeableitung in groĂskalierten integrierten Schaltkreisen und die daraus resultierende Ăberhitzung des Chips. Um diesem Problem in modernen Multi-Core Architekturen zu begegnen, muss auch die Verlustleistung der Netzwerkressourcen stark reduziert werden. Diese Arbeit umfasst eine durch Hardware gesteuerte Kombination aus Frequenzskalierung und Power Gating fĂŒr 3D On-Chip Netzwerke, einschlieĂlich eines FPGA Prototypen. DafĂŒr wurde ein Takt-synchrones 2D Netzwerk auf ein dreidimensionales asynchrones Netzwerk mit mehreren Frequenzbereichen erweitert. ZusĂ€tzlich wurde ein skalierbares Online-Power-Management System mit geringem Ressourcenaufwand entwickelt.
Die Verifikation neuer Hardwarekomponenten ist einer der zeitaufwendigsten Schritte im Entwicklungsprozess hochintegrierter digitaler Schaltkreise. Um diese Aufgabe zu beschleunigen und um eine parallele Softwareentwicklung zu ermöglichen, wurde im Rahmen dieser Arbeit ein automatisiertes und benutzerfreundliches Tool fĂŒr den Entwurf neuer Hardware Projekte entwickelt. Eine grafische BenutzeroberflĂ€che zum Erstellen des gesamten Designablaufs, vom Erstellen der Architektur, Parameter Deklaration, Simulation, Synthese und Test ist Teil dieses Werkzeugs. Zudem stellt die GröĂe der Architektur fĂŒr die Erstellung eines Prototypen eine besondere Herausforderung dar. FrĂŒhere Arbeiten haben es versĂ€umt, eine schnelles und unkompliziertes Prototyping, insbesondere von Architekturen mit mehr als 50 Prozessorkernen, zu realisieren. Diese Arbeit umfasst eine Design Space Exploration und FPGA-basierte Prototypen von verschiedenen 3D-NoC Implementierungen mit mehr als 80 Prozessoren
Task allocation in group of nodes in the IoT: A consensus approach
The realization of the Internet of Things (IoT) paradigm relies on the implementation of systems of cooperative intelligent objects with key interoperability capabilities. In order for objects to dynamically cooperate to IoT applications' execution, they need to make their resources available in a flexible way. However, available resources such as electrical energy, memory, processing, and object capability to perform a given task, are often limited. Therefore, resource allocation that ensures the fulfilment of network requirements is a critical challenge. In this paper, we propose a distributed optimization protocol based on consensus algorithm, to solve the problem of resource allocation and management in IoT heterogeneous networks. The proposed protocol is robust against links or nodes failures, so it's adaptive in dynamic scenarios where the network topology changes in runtime. We consider an IoT scenario where nodes involved in the same IoT task need to adjust their task frequency and buffer occupancy. We demonstrate that, using the proposed protocol, the network converges to a solution where resources are homogeneously allocated among nodes. Performance evaluation of experiments in simulation mode and in real scenarios show that the algorithm converges with a percentage error of about±5% with respect to the optimal allocation obtainable with a centralized approach
- âŠ