Geometrically-constrained, parasitic-aware synthesis of analog ICs

In order to speed up the design process of analog ICs, iterations between different design stages should be avoided as much as possible. More specifically, spins between electrical and physical synthesis should be reduced for this is a very time-consuming task: if circuit performance including layout-induced degradations proves unacceptable, a re-design cycle must be entered, and electrical, physical, or both synthesis processes, would have to be repeated. It is also worth noting that if geometric optimization (e.g., area minimization) is undertaken after electrical synthesis, it may add up as another source of unexpected degradation of the circuit performance due to the impact of the geometric variables (e.g., transistor folds) on the device and the routing parasitic values. This awkward scenario is caused by the complete separation of said electrical and physical synthesis, a design practice commonly followed so far. Parasitic-aware synthesis, consisting in including parasitic estimates to the circuit netlist directly during electrical synthesis, has been proposed as solution. While most of the reported contributions either tackle parasitic-aware synthesis without paying special attention to geometric optimization or approach both issues only partially, this paper addresses the problem in a unified way. In what has been called layout-aware electrical synthesis, a simulation-based optimization algorithm explores the design space with geometric variables constrained to meet certain user-defined goals, which provides reliable estimates of layout-induced parasitics at each iteration, and, thereby, accurate evaluation of the circuit ultimate performance. This technique, demonstrated here through several design examples, requires knowing layout details beforehand; to facilitate this, procedural layout generation is used as physical synthesis approach due to its rapidness and ability to capture analog layout know-how.Ministerio de Educación y Ciencia TEC2004-0175

Transistor-Level Layout of Integrated Circuits

In this dissertation, we present the toolchain BonnCell and its underlying algorithms. It has been developed in close cooperation with the IBM Corporation and automatically generates the geometry for functional groups of 2 to approximately 50 transistors. Its input consists of a set of transistors, including properties like their sizes and their types, a specification of their connectivity, and parameters to flexibly control the technological framework as well as the algorithms' behavior. Using this data, the tool computes a detailed geometric realization of the circuit as polygonal shapes on 16 layers. To this end, a placement routine configures the transistors and arranges them in the plane, which is the main subject of this thesis. Subsequently, a routing engine determines wires connecting the transistors to ensure the circuit's desired functionality. We propose and analyze a family of algorithms that arranges sets of transistors in the plane such that a multi-criteria target function is optimized. The primary goal is to obtain solutions that are as compact as possible because chip area is a valuable resource in modern techologies. In addition to the core algorithms we formulate variants that handle particularly structured instances in a suitable way. We will show that for 90% of the instances in a representative test bed provided by IBM, BonnCell succeeds to generate fully functional layouts including the placement of the transistors and a routing of their interconnections. Moreover, BonnCell is in wide use within IBM's groups that are concerned with transistor-level layout - a task that has been performed manually before our automation was available. Beyond the processing of isolated test cases, two large-scale examples for applications of the tool in the industry will be presented: On the one hand the initial design phase of a large SRAM unit required only half of the expected 3 month period, on the other hand BonnCell could provide valuable input aiding central decisions in the early concept phase of the new 14 nm technology generation

Automatic synthesis of analog layout : a survey

A review of recent research in the automatic synthesis of physical geometry for analog integrated circuits is presented. On introduction, an explanation of the difficulties involved in analog layout as opposed to digital layout is covered. Review of the literature then follows. Emphasis is placed on the exposition of general methods for addressing problems specific to analog layout, with the details of specific systems only being given when they surve to illustrate these methods well. The conclusion discusses problems remaining and offers a prediction as to how technology will evolve to solve them. It is argued that although progress has been and will continue to be made in the automation of analog IC layout, due to fundamental differences in the nature of analog IC design as opposed to digital design, it should not be expected that the level of automation of the former will reach that of the latter any time soon

Lensfree computational microscopy tools for cell and tissue imaging at the point-of-care and in low-resource settings.

The recent revolution in digital technologies and information processing methods present important opportunities to transform the way optical imaging is performed, particularly toward improving the throughput of microscopes while at the same time reducing their relative cost and complexity. Lensfree computational microscopy is rapidly emerging toward this end, and by discarding lenses and other bulky optical components of conventional imaging systems, and relying on digital computation instead, it can achieve both reflection and transmission mode microscopy over a large field-of-view within compact, cost-effective and mechanically robust architectures. Such high throughput and miniaturized imaging devices can provide a complementary toolset for telemedicine applications and point-of-care diagnostics by facilitating complex and critical tasks such as cytometry and microscopic analysis of e.g., blood smears, Pap tests and tissue samples. In this article, the basics of these lensfree microscopy modalities will be reviewed, and their clinically relevant applications will be discussed

Optimal 2-D cell layout with integrated transistor folding

ABSTRACT Folding, a key requirement in high-performance cell layout, implies breaking a large transistor into smaller, equal-sized transistors (legs) that are connected in parallel and placed contiguously with diffusion sharing. We present a novel technique FCLIP that integrates folding into the generation of optimal layouts of CMOS cells in the twodimensional (2-D) style. FCLIP is based on integer linear programming (ILP) and precisely formulates cell width minimization as a 0-1 optimization problem. Folding is incorporated into the 0-1 ILP model by variables that represent the degrees of freedom that folding introduces into cell layout. FCLIP yields optimal results for three reasons: (1) it implicitly explores all possible transistor placements; (2) it considers all diffusion sharing possibilities among folded transistors; and (3) when paired P and N transistors have unequal numbers of legs, it considers all their relative positions. FCLIP is shown to be practical for relatively large circuits with up to 30 transistors. We then extend FCLIP to accommodate and-stack clustering, a requirement in most practical designs due to its benefits on circuit performance. This reduces run times dramatically, making FCLIP viable for much larger circuits. It also demonstrates the versatility of FCLIP's ILP-based approach in easily accommodating additional design constraints. INTRODUCTION Cell layout synthesis falls in the category of constrained optimization whose goal is to find a solution that optimizes some cost function under a set of constraints. The cost function can be the cell area, its delay, or a combination of these. The constraints include bounds on width or height, aspect ratio, number of diffusion rows, or the maximum size of transistors. Since cell layout optimization is NP-hard [3], any exact algorithm can, in the worst case, have an exponential run time. Therefore, most prior techniques for cell synthesis have avoided optimal algorithms in favor of faster, but less exact heuristic methods. Maziasz and Hayes FCLIP minimizes cell area in the following stages: First, transistors are folded based on user-specified limits on the maximum size of the P and N transistors. The input circuit is preprocessed to generate P/N pairs and identify and-stacks, that is, transistors that are connected in series. And-stack clustering is not only necessary in practical designs, but also reduces the complexity of the problem and, in turn, FCLIP's run times. Then an ILP model is formulated and solved to determine a 2-D layout of minimum width W min ; this model maximizes diffusion sharing among folded transistors and minimizes vertical inter-row connections. A second ILP model is then constructed to generate a layout that has width W min and minimum height, measured by the number of horizontal routing tracks. This paper only discusses 2-D cell width minimization with folding; however, FCLIP can be extended to minimize cell height also. FCLIP yields optimal results with folding for two reasons: (1) It implicitly explores all diffusion sharing possibilities among folded transistors; and (2) when paired P/N transistors have unequal numbers of legs, it considers all their relative positions. Not only does FCLIP support 2-D layout, it is superior to prior folding techniques proposed for 1-D layou

Leakage Minimization Technique for Nanoscale CMOS VLSI

Because of the continued scaling of technology and supply-threshold voltage, leakage power has become more significant in power dissipation of nanoscale CMOS circuits. Therefore, estimating the total leakage power is critical to designing low-power digital circuits. In nanometer CMOS circuits, the main leakage components are the subthreshold, gate-tunneling, and reverse-biased junction band-to-band-tunneling (BTBT) leakage currents

Emerging Technologies - NanoMagnets Logic (NML)

In the last decades CMOS technology has ruled the electronic scenario thanks to the constant scaling of transistor sizes. With the reduction of transistor sizes circuit area decreases, clock frequency increases and power consumption decreases accordingly. However CMOS scaling is now approaching its physical limits and many believe that CMOS technology will not be able to reach the end of the Roadmap. This is mainly due to increasing difficulties in the fabrication process, that is becoming very expensive, and to the unavoidable impact of leakage losses, particularly thanks to gate tunnel current. In this scenario many alternative technologies are studied to overcome the limitations of CMOS transistors. Among these possibilities, magnetic based technologies, like NanoMagnet Logic (NML) are among the most interesting. The reason of this interest lies in their magnetic nature, that opens up entire new possibilities in the design of logic circuits, like the possibility to mix logic and memory in the same device. Moreover they have no standby power consumption and potentially a much lower power consumption of CMOS transistors. In literature NML logic is well studied and theoretical and experimental proofs of concept were already found. However two important points are not enough considered in the analysis approach followed by most of the work in literature. First of all, no complex circuits are analyzed. NML logic is very different from CMOS technologies, so to completely understand the potential of this technology it is mandatory to investigate complex architectures. Secondly, most of the solutions proposed do not take into account the constraints derived from fabrication process, making them unrealistic and difficult to be fabricated experimentally. This thesis focuses therefore on NML logic keeping into account these two important limitations in the research approach followed in literature. The aim is to obtain a complete and accurate overview of NML logic, finding realistic circuital solutions and trying to improve at the same time their performance. After a brief and complete introduction (Chapter 1), the thesis is divided in two parts, which cover the two fundamental points followed in this three years of research: A circuits architecture analysis and a technological analysis. In the architecture analysis first an innovative VHDL model is described in Chapter 2. This model is extensively used in the analysis because it allows fast simulation of complex circuits, with, at the same time, the possibility to estimate circuit per- formance, like area and power consumption. In Chapter 3 the problem of signals synchronization in complex NML circuits is analyzed and solved, using as benchmark a simple but complete NML microprocessor. Different solutions based on asynchronous logic are studied and a new asynchronous solution, specifically designed to exploit the potential of NML logic, is developed. In Chapter 4 the layout of NML circuits is studied on a more physical level, considering the limitations of fabrication processes. The layout of NML circuits is therefore changed accordingly to these constraints. Secondly CMOS circuits architectures are compared to more simple architectures, evaluating therefore which one is more suited for NML logic. Finally the problem of interconnections in NML technology is analyzed and solutions to improve it are found. In Chapter 5 the problem of feedback signals in heavy pipelined technologies, like NML, is studied. Solutions to improve performances and synchronize signals are developed. Systolic arrays are then analyzed as possible candidate to exploit NML potential. Finally in Chapter 6 ToPoliNano, a simulator dedicated to NML and other emerging technologies, that we are developing, is described. This simulator allows to follow the same top-down approach followed for CMOS technology. The layout generator and the simulation engine are detailed described. In the first chapter of the technological analysis (Chapter 7), the performance of NML logic is explored throughout low level simulations. The aim is to understand if these circuits can be fabricated with optical lithography, allowing therefore the commercial development of NML logic. Basic logic gates and the clock system are there analyzed from a low level perspective. In Chapter 8 an innovative electric clock system for NML technology is shown and the first experimental results are reported. This clock system allows to achieve true low power for NML technology, obtaining a reduction of power consumption of 20 times considering the best CMOS transistors available. This power consumption takes into account all the losses, also the clock system losses. Moreover the solution presented can be fabricated with current technological processes. The research work behind this thesis represents an important breakthrough in NML logic. The solutions here presented allow the design and fabrication of complex NML circuits, considering the particular characteristics of this technology and considerably improving the performance. Moreover the technological solutions here presented allow the design and fabrication of circuits with available fabrication process with a considerable advantage over CMOS in terms of power consumption. This thesis represents therefore a considerable step froward in the study and development of NML technolog

CMOS-based Single-Cycle In-Memory XOR/XNOR

Big data applications are on the rise, and so is the number of data centers. The ever-increasing massive data pool needs to be periodically backed up in a secure environment. Moreover, a massive amount of securely backed-up data is required for training binary convolutional neural networks for image classification. XOR and XNOR operations are essential for large-scale data copy verification, encryption, and classification algorithms. The disproportionate speed of existing compute and memory units makes the von Neumann architecture inefficient to perform these Boolean operations. Compute-in-memory (CiM) has proved to be an optimum approach for such bulk computations. The existing CiM-based XOR/XNOR techniques either require multiple cycles for computing or add to the complexity of the fabrication process. Here, we propose a CMOS-based hardware topology for single-cycle in-memory XOR/XNOR operations. Our design provides at least 2 times improvement in the latency compared with other existing CMOS-compatible solutions. We verify the proposed system through circuit/system-level simulations and evaluate its robustness using a 5000-point Monte Carlo variation analysis. This all-CMOS design paves the way for practical implementation of CiM XOR/XNOR at scaled technology nodes.Comment: 12 pages, 6 figures, 1 tabl