28 research outputs found

    Physical Layer Techniques for OFDM-Based Cognitive Radios

    Get PDF
    Cognitive radio has recently been proposed as a promising approach for efficient utilization of radio spectrum. However, there are several challenges to be addressed across all layers of a cognitive radio system design, from application to hardware implementation. From the physical layer point-of-view, two key challenges are spectrum sensing and an appropriate signaling scheme for data transmission. The modulation techniques used in cognitive radio not only should be efficient and flexible but also must not cause (harmful) interference to the primary (licensed) users. Among all the proposed signaling schemes for cognitive radio, orthogonal frequency division multiplexing (OFDM) has emerged as a promising one due to its robustness against multipath fading, high spectral efficiency, and capacity for dynamic spectrum use. However, OFDM suffers from high out-of-band radiation which is due to high sidelobes of subcarriers. In this thesis, we consider spectral shaping in OFDM-based cognitive radio systems with focus on reducing interference to primary users created by by out-of-band radiation of secondary users' OFDM signal. In the first part of this research, we first study the trade-o between time-based and frequency-based methods proposed for sidelobe suppression in OFDM. To this end, two recently proposed techniques, active interference cancellation (AIC) and adaptive symbol transition (AST), are considered and a new joint time-frequency scheme is developed for both single-antenna and multi-antenna systems. Furthermore, knowledge of wireless channel is used in the setting of the proposed joint scheme to better minimize interference to the primary user. This scheme enables us to evaluate the trade-o between the degrees of freedom provided by each of the two aforementioned methods. In the second part of this research, a novel low-complexity technique for reducing out-of-band radiation power of OFDM subcarriers for both single-antenna and multi-antenna systems is proposed. In the new technique, referred to as a phase adjustment technique, each OFDM symbol is rotated in the complex plane by an optimal phase such that the interference to primary users is minimized. It is shown that the phase adjustment technique neither reduces the system throughput, nor does increase the bit-error-rate of the system. Moreover, the performance of the technique in interference reduction is evaluated analytically in some special cases and is verified using numerical simulations. Due to high sensitivity of OFDM systems to time and frequency synchronization errors, performance of spectral shaping techniques in OFDM is significantly affected by timing jitter in practical systems. In the last part of this research, we investigate the impact of timing jitter on sidelobe suppression techniques. Considering AIC as the base method of sidelobe suppression, we first propose a mathematical model for OFDM spectrum in presence of timing jitter and evaluate the performance degradation to AIC due to timing jitter. Then, a precautionary scheme based on a minimax approach is proposed to make the technique robust against random timing jitter.4 month

    High speed energy efficient incoherent optical wireless communications

    Get PDF
    The growing demand for wireless communication capacity and the overutilisation of the conventional radio frequency (RF) spectrum have inspired research into using alternative spectrum regions for communication. Using optical wireless communications (OWC), for example, offers significant advantages over RF communication in terms of higher bandwidth, lower implementation costs and energy savings. In OWC systems, the information signal has to be real and non-negative. Therefore, modifications to the conventional communication algorithms are required. Multicarrier modulation schemes like orthogonal frequency division multiplexing (OFDM) promise to deliver a more efficient use of the communication capacity through adaptive bit and energy loading techniques. Three OFDM-based schemes – direct-current-biased OFDM (DCO-OFDM), asymmetrically clipped optical OFDM(ACO-OFDM), and pulse-amplitude modulated discrete multitone (PAM-DMT) – have been introduced in the literature. The current work investigates the recently introduced scheme subcarrier-index modulation OFDM as a potential energy-efficient modulation technique with reduced peak-to-average power ratio (PAPR) suitable for applications in OWC. A theoretical model for the analysis of SIM-OFDMin a linear additive white Gaussian noise (AWGN) channel is provided. A closed-form solution for the PAPR in SIM-OFDM is also proposed. Following the work on SIM-OFDM, a novel inherently unipolar modulation scheme, unipolar orthogonal frequency division multiplexing (U-OFDM), is proposed as an alternative to the existing similar schemes: ACO-OFDMand PAM-DMT. Furthermore, an enhanced U-OFDMsignal generation algorithm is introduced which allows the spectral efficiency gap between the inherently unipolar modulation schemes – U-OFDM, ACO-OFDM, PAM-DMT – and the conventionally used DCO-OFDM to be closed. This results in an OFDM-based modulation approach which is electrically and optically more efficient than any other OFDM-based technique proposed so far for intensity modulation and direct detection (IM/DD) communication systems. Non-linear distortion in the optical front-end elements is one of the major limitations for high-speed communication in OWC. This work presents a generalised approach for analysing nonlinear distortion in OFDM-based modulation schemes. The presented technique leads to a closed-form analytical solution for an arbitrary memoryless distortion of the information signal and has been proven to work for the majority of the known unipolar OFDM-based modulation techniques - DCO-OFDM, ACO-OFDM, PAM-DMT and U-OFDM. The high-speed communication capabilities of novel Gallium Nitride based μm-sized light emitting diodes (μLEDs) are investigated, and a record-setting result of 3.5Gb/s using a single 50-μm device is demonstrated. The capabilities of using such devices at practical transmission distances are also investigated, and a 1 Gb/s link using a single device is demonstrated at a distance of up to 10m. Furthermore, a proof-of-concept experiment is realised where a 50-μm LED is successfully modulated using U-OFDM and enhanced U-OFDM to achieve notable energy savings in comparison to DCO-OFDM

    Channel Estimation and Prediction in LTE

    Get PDF

    Performance analysis of OFDM technology on radio-over-fiber systems

    Get PDF
    Dissertação de mest., Engenharia Eletrónica e Telecomunicações, Faculdade de Ciências e Tecnologia, Univ. do Algarve, 2011Nowadays, the demand for high speed, high quality and diversity in distributed services presents a challenge for telecommunication technology. Wireless systems provide the accessibility to end-user, but are not the solution for long distance links. Currently, the ideal technology for long-range transmissions at high data rates is optical fiber. Hence, a new concept for high capacity networks emerges, with centralized services into Base Stations (BS) engineered to provide flexibility and control over the system, and to perform operations such as electrical to optical domain conversion and modulation. Such Radio-over-Fiber (RoF) networks also appear as an attractive technology because they are efficient and cost effective. Orthogonal Frequency Division Multiplexing (OFDM) technology is widely used in a number of standards. For instance, it is actually the Multi-Carrier Modulation (MCM) technique applied in 802.11a/g/n wireless standards and in Digital Video Broadcasting-Terrestrial (DVB-T), among other prevailing systems, which makes this subject one particularly pertinent to study. OFDM systems are an appealing choice for waveform modulation, as they are very bandwidth efficient comparing to others MCM, and provide flexibility in data transmission rates. Additionally, an important advantage dwells in its natural robustness against severely interfering environments. In this thesis, fundamentals on OFDM technology are extensively described, and its application to wireless and optical fiber networks is introduced. The combined channel effects of these technologies on OFDM signals are investigated. In terms of performance analysis, this exposition focuses on understanding the importance of OFDM modulation parameters, and explores some OFDM signal properties. To achieve this, a simulator was implemented with Matlab to create arbitrary OFDM waveforms and emulate channel effects. This study also investigates the efficiency of OFDM technology over a real Radio Frequency (RF) system with an ideal communication channel. Finally, an experimental RoF configuration is implemented and its performance is assessed

    Bandwidth Compressed Waveform and System Design for Wireless and Optical Communications: Theory and Practice

    Get PDF
    This thesis addresses theoretical and practical challenges of spectrally efficient frequency division multiplexing (SEFDM) systems in both wireless and optical domains. SEFDM improves spectral efficiency relative to the well-known orthogonal frequency division multiplexing (OFDM) by non-orthogonally multiplexing overlapped sub-carriers. However, the deliberate violation of orthogonality results in inter carrier interference (ICI) and associated detection complexity, thus posing many challenges to practical implementations. This thesis will present solutions for these issues. The thesis commences with the fundamentals by presenting the existing challenges of SEFDM, which are subsequently solved by proposed transceivers. An iterative detection (ID) detector iteratively removes self-created ICI. Following that, a hybrid ID together with fixed sphere decoding (FSD) shows an optimised performance/complexity trade-off. A complexity reduced Block-SEFDM can subdivide the signal detection into several blocks. Finally, a coded Turbo-SEFDM is proved to be an efficient technique that is compatible with the existing mobile standards. The thesis also reports the design and development of wireless and optical practical systems. In the optical domain, given the same spectral efficiency, a low-order modulation scheme is proved to have a better bit error rate (BER) performance when replacing a higher order one. In the wireless domain, an experimental testbed utilizing the LTE-Advanced carrier aggregation (CA) with SEFDM is operated in a realistic radio frequency (RF) environment. Experimental results show that 40% higher data rate can be achieved without extra spectrum occupation. Additionally, a new waveform, termed Nyquist-SEFDM, which compresses bandwidth and suppresses out-of-band power leakage is investigated. A 4th generation (4G) and 5th generation (5G) coexistence experiment is followed to verify its feasibility. Furthermore, a 60 GHz SEFDM testbed is designed and built in a point-to-point indoor fiber wireless experiment showing 67% data rate improvement compared to OFDM. Finally, to meet the requirements of future networks, two simplified SEFDM transceivers are designed together with application scenarios and experimental verifications

    Spectrum Optimisation in Wireless Communication Systems: Technology Evaluation, System Design and Practical Implementation

    Get PDF
    Two key technology enablers for next generation networks are examined in this thesis, namely Cognitive Radio (CR) and Spectrally Efficient Frequency Division Multiplexing (SEFDM). The first part proposes the use of traffic prediction in CR systems to improve the Quality of Service (QoS) for CR users. A framework is presented which allows CR users to capture a frequency slot in an idle licensed channel occupied by primary users. This is achieved by using CR to sense and select target spectrum bands combined with traffic prediction to determine the optimum channel-sensing order. The latter part of this thesis considers the design, practical implementation and performance evaluation of SEFDM. The key challenge that arises in SEFDM is the self-created interference which complicates the design of receiver architectures. Previous work has focused on the development of sophisticated detection algorithms, however, these suffer from an impractical computational complexity. Consequently, the aim of this work is two-fold; first, to reduce the complexity of existing algorithms to make them better-suited for application in the real world; second, to develop hardware prototypes to assess the feasibility of employing SEFDM in practical systems. The impact of oversampling and fixed-point effects on the performance of SEFDM is initially determined, followed by the design and implementation of linear detection techniques using Field Programmable Gate Arrays (FPGAs). The performance of these FPGA based linear receivers is evaluated in terms of throughput, resource utilisation and Bit Error Rate (BER). Finally, variants of the Sphere Decoding (SD) algorithm are investigated to ameliorate the error performance of SEFDM systems with targeted reduction in complexity. The Fixed SD (FSD) algorithm is implemented on a Digital Signal Processor (DSP) to measure its computational complexity. Modified sorting and decomposition strategies are then applied to this FSD algorithm offering trade-offs between execution speed and BER

    Modeling and Optimization of Next-Generation Wireless Access Networks

    Get PDF
    The ultimate goal of the next generation access networks is to provide all network users, whether they are fixed or mobile, indoor or outdoor, with high data rate connectivity, while ensuring a high quality of service. In order to realize this ambitious goal, delay, jitter, error rate and packet loss should be minimized: a goal that can only be achieved through integrating different technologies, including passive optical networks, 4th generation wireless networks, and femtocells, among others. This thesis focuses on medium access control and physical layers of future networks. In this regard, the first part of this thesis discusses techniques to improve the end-to-end quality of service in hybrid optical-wireless networks. In these hybrid networks, users are connected to a wireless base station that relays their data to the core network through an optical connection. Hence, by integrating wireless and optical parts of these networks, a smart scheduler can predict the incoming traffic to the optical network. The prediction data generated herein is then used to propose a traffic-aware dynamic bandwidth assignment algorithm for reducing the end-to-end delay. The second part of this thesis addresses the challenging problem of interference management in a two-tier macrocell/femtocell network. A high quality, high speed connection for indoor users is ensured only if the network has a high signal to noise ratio. A requirement that can be fulfilled with using femtocells in cellular networks. However, since femtocells generate harmful interference to macrocell users in proximity of them, careful analysis and realistic models should be developed to manage the introduced interference. Thus, a realistic model for femtocell interference outside suburban houses is proposed and several performance measures, e.g., signal to interference and noise ratio and outage probability are derived mathematically for further analysis. The quality of service of cellular networks can be degraded by several factors. For example, in industrial environments, simultaneous fading and strong impulsive noise significantly deteriorate the error rate performance. In the third part of this thesis, a technique to improve the bit error rate of orthogonal frequency division multiplexing systems in industrial environments is presented. This system is the most widely used technology in next-generation networks, and is very susceptible to impulsive noise, especially in fading channels. Mathematical analysis proves that the proposed method can effectively mitigate the degradation caused by impulsive noise and significantly improve signal to interference and noise ratio and bit error rate, even in frequency-selective fading channels

    Fiber-based orthogonal frequency division multiplexing transmission systems

    Get PDF
    Orthogonal Frequency Division Multiplexing (OFDM) is the underlying modulation and transmission technology behind the success of modern wireless standards for both cellular, digital television and digital radio communications and also for Digital Subscriber Line wired access. Higher data rates to handle and the special nature of electronic-optic conversions and of optical wave propagation, can hold the key as to why it is only now that OFDM signal transmission over fiber is starting to take off. In this Master Thesis Project we aim at establishing the basis of OFDM transmission over optical fiber for both direct-detection as well as coherent systems, for different optical modulation formats at the emitter; and to characterize their performance as a function of key parameters such as fiber chromatic dispersion, the amount of Cyclic Prefix, Peak to Average Power Ratio, etc. through the use of optical transmission simulation packages such as Virtual Photonics Inc

    Oblique Sounding and HF Communication Techniques for Very Long Haul Ionospheric Links

    Get PDF
    El sistema de comunicació ràdio d’alta freqüència (HF, en anglès) és usat arreu del món per agències governamentals i no governamentals sempre que calgui una alternativa a les comunicacions via satèl•lit: vaixells a alta mar, avions fora de cobertura de xarxes ràdio amb visió directa, operacions militars, zones on la infraestructura ha estat destruïda per algun tipus de desastre o bé zones llunyanes sense cap altre tipus de comunicació. La ràdio HF representa una alternativa, o un sistema de backup al satèl•lit per a comunicacions de llarg abast i en redueix els costos, evita la vulnerabilitat i els problemes de sobirania. En aquesta tesi s’ha estudiat l’enllaç HF entre la base antàrtica espanyola Juan Carlos I, situada a l’illa Livingston a l’arxipèlag de les Shetland del Sud, i Espanya. L’objectiu d’aquest treball és estudiar els problemes que afecten la propagació; és a dir, la relació senyal a soroll i interferència, la dispersió multicamí i la dispersió per efecte Doppler, i dissenyar la capa física d’un enllaç HF de baixa velocitat, poca potència i llarg abast. Pel que fa aquest últim punt es fan un parell de propostes: espectre eixamplat per seqüència directa (DSSS, en anglès) i multiplexació per divisió en freqüència ortogonal (OFDM, en anglès). El repte que es planteja és el de la definició de les característiques dels símbols que millor encaixen en aquest canal per tal d’obtenir un benefici de la diversitat temporal i freqüencial que ofereix el canal. Des de l’any 2003 diverses campanyes han permès estudiar aquest canal HF, però no va ser fins la campanya 2009/2010 que s’obtingué un foto de les característiques, diürnes i nocturnes, de la ionosfera. En els articles que es presenten en aquesta tesi hem estès el rang freqüencial d’estudi respecte a investigacions prèvies i hem mostrat diferències de comportament entre el dia i la nit. Hem usat els resultats de la caracterització del canal per a dissenyar i comparar la bondat dels símbols DSSS i OFDM. Ambdues possibilitats han resultat ser candidates a implementar l’enllaç HF entre l’Antàrtida i Espanya. Tot i així, ambdues tècniques representen visions diferents de la implementació del mòdem: mentre que DSSS obté bons resultats a baixa velocitat en entorns amb baixa relació senyal a soroll, OFDM aconsegueix tasses de velocitat més elevades en canals més benignes.Los sistemas de radio de alta frecuencia (HF, en inglés) son usados por agencias gubernamentales y no gubernamentales en todo el mundo siempre que se necesite una alternativa a las comunicaciones por satélite: barcos en alta mar, aviones fuera del rango de cobertura de las redes radio de visión directa, operaciones militares, zonas donde la infraestructura ha sido destruida por algún desastre. Ésta ofrece una alternativa, o representa un sistema de backup, a las comunicaciones vía satélite, evitando los costes, la vulnerabilidad y los problemas de soberanía de las comunicaciones por satélite. En esta tesis se ha estudiado el enlace HF entre la base antártica española Juan Carlos I en la isla Livingston, en las Shetland del sur y España. El objetivo de este trabajo es el estudio de las limitaciones de la propagación ionosférica (como la relación señal a ruido e interferencia, la dispersión multicamino y la dispersión por efecto Doppler) y el diseño de la capa física de un enlace HF de baja velocidad, baja potencia y largo alcance. Se han estudiado un par de propuestas para este enlace, como son el espectro ensanchado por secuencia directa (DSSS, en inglés) y la multiplexación por división en frecuencia ortogonal (OFDM, en inglés). El reto ha sido definir las características que mejor se adecuan a este enlace para poder aprovechar la diversidad temporal y frecuencial que ofrece el canal HF. Desde el año 2003 diversas campañas de sondeo han permitido estudiar el canal HF pero no es hasta la campaña 2009/2010 que se consigue una fotografía de la actividad ionosférica tanto nocturna como diurna. En los artículos que se presentan en esta tesis hemos extendido los estudios previos a todo el rango de frecuencias HF y hemos mostrado las diferencias entre el día y la noche. Hemos usado estos resultados de caracterización del canal para diseñar y comparar símbolos DSSS y símbolos OFDM. Ambas posibilidades han resultado ser posibles candidatas para implementar un enlace HF de baja velocidad entre la Antártida y España. Sin embargo ambas técnicas representan dos aproximaciones distintas a la implementación del módem. Mientras que DSSS consigue un buen funcionamiento a baja velocidad en escenarios con baja relación señal a ruido, OFDM consigue tasas de transmisión más altas en escenarios más benignos.High Frequency (HF) radio is used by governmental and non nongovernmental agencies worldwide whenever an alternative to satellites for sky wave communication is needed: ships at sea, aircraft out of range of line-of-sight radio networks, military operations, disaster areas with communication infrastructure destroyed or distant regions lacking other communications. It offers an alternative to satellites, or a backup, for long-haul communications, thus avoiding the costs, vulnerabilities and sovereignty concerns of satellite communications. In this thesis the HF link between the Antarctic Spanish Station Juan Carlos I in Livingston Island, South Shetlands and Spain is studied. The aim of this study is to address the impairments that affect HF propagation (i.e., signal-to-noise plus interference ratio, multipath and Doppler shift and spread) and to design the physical layer of a low rate, low power and long-haul HF link. Some proposals regarding this last issue are addressed, i.e., direct sequence spread spectrum (DSSS) and orthogonal frequency division multiplexing (OFDM). The challenge is to define the symbol characteristics that best fit the link to benefit from time and frequency diversity that offers the HF channel. Since 2003 several transmission campaigns have allowed to study the HF channel but it is not until the 2009/2010 campaign that we have achieved a whole picture of both diurnal and nocturnal ionospheric activity. In the papers presented in this thesis we have extended the previous research to the whole range of HF frequencies and we have shown the differences on performance between day and night. We have used the results from channel characterization to design and compare the performance of DSSS and OFDM symbols. Both techniques have turned out to be possible candidates to implement a low rate HF link between Antarctica and Spain. However, both techniques stand for different approaches of the modem: DSSS achieves good performance at low data rate in low SNR scenarios, whereas OFDM achieves higher data rate in benign channel
    corecore