Evaluation of Modified Non-Normal Process Capability Index and Its Bootstrap Confidence Intervals

Process capability index (PCI) is used to quantify the process performance and is becoming an attracted area of research. A variability measure plays an important role in PCI. The interquartile range (IQR) or the median absolute deviation (MAD) is commonly used for a variability measure in estimating PCI when a process follows a non-normal distribution In this paper, the efficacy of the IQR and MAD-based PCIs was evaluated under low, moderate, and high asymmetric behavior of the Weibull distribution using different sample sizes through three different bootstrap confidence intervals. The result reveals that MAD performs better than IQR, because the former produced less bias and mean square error. Also, the percentile bootstrap confidence interval is recommended for use, because it has less average width and high coverage probability.11Ysciescopu

Capability Indices for Non-Normal Distribution using Gini’s Mean Difference as Measure of Variability

This paper investigates the efficiency of Gini's mean difference (GMD) as a measure of variability in two commonly used process capability indices (PCIs), i.e., Cp and Cpk. A comparison has been carried out to evaluate the performance of GMD-based PCIs and Pearn and Chen quantile-based PCIs under low, moderate, and high asymmetry using Weibull distribution. The simulation results, under low and moderate asymmetric condition, indicate that GMD-based PCIs are more close to target values than quantile approach. Beside point estimation, nonparametric bootstrap confidence intervals, such as standard, percentile, and bias corrected percentile with their coverage probabilities also have been calculated. Using quantile approach, bias corrected percentile (BCPB) method is more effective for both Cp and Cpk, where as in case of GMD, both BCPB and percentile bootstrap method can be used to estimate the confidence interval of Cp and Cpk, respectively.1133Ysciescopu

Attitudes towards old age and age of retirement across the world: findings from the future of retirement survey

The 21st century has been described as the first era in human history when the world will no longer be young and there will be drastic changes in many aspects of our lives including socio-demographics, financial and attitudes towards the old age and retirement. This talk will introduce briefly about the Global Ageing Survey (GLAS) 2004 and 2005 which is also popularly known as “The Future of Retirement”. These surveys provide us a unique data source collected in 21 countries and territories that allow researchers for better understanding the individual as well as societal changes as we age with regard to savings, retirement and healthcare. In 2004, approximately 10,000 people aged 18+ were surveyed in nine counties and one territory (Brazil, Canada, China, France, Hong Kong, India, Japan, Mexico, UK and USA). In 2005, the number was increased to twenty-one by adding Egypt, Germany, Indonesia, Malaysia, Poland, Russia, Saudi Arabia, Singapore, Sweden, Turkey and South Korea). Moreover, an additional 6320 private sector employers was surveyed in 2005, some 300 in each country with a view to elucidating the attitudes of employers to issues relating to older workers. The paper aims to examine the attitudes towards the old age and retirement across the world and will indicate some policy implications

The Influence of Roughness on Gear Surface Fatigue

Gear working surfaces are subjected to repeated rolling and sliding contacts, and often designs require loads sufficient to cause eventual fatigue of the surface. This research provides experimental data and analytical tools to further the understanding of the causal relationship of gear surface roughness to surface fatigue. The research included evaluations and developments of statistical tools for gear fatigue data, experimental evaluation of the surface fatigue lives of superfinished gears with a near-mirror quality, and evaluations of the experiments by analytical methods and surface inspections. Alternative statistical methods were evaluated using Monte Carlo studies leading to a final recommendation to describe gear fatigue data using a Weibull distribution, maximum likelihood estimates of shape and scale parameters, and a presumed zero-valued location parameter. A new method was developed for comparing two datasets by extending the current methods of likelihood-ratio based statistics. The surface fatigue lives of superfinished gears were evaluated by carefully controlled experiments, and it is shown conclusively that superfinishing of gears can provide for significantly greater lives relative to ground gears. The measured life improvement was approximately a factor of five. To assist with application of this finding to products, the experimental condition was evaluated. The fatigue life results were expressed in terms of specific film thickness and shown to be consistent with bearing data. Elastohydrodynamic and stress analyses were completed to relate the stress condition to fatigue. Smooth-surface models do not adequately explain the improved fatigue lives. Based on analyses using a rough surface model, it is concluded that the improved fatigue lives of superfinished gears is due to a reduced rate of near-surface micropitting fatigue processes, not due to any reduced rate of spalling (sub-surface) fatigue processes. To complete the evaluations, surface inspection were completed. The surface topographies of the ground gears changed substantially due to running, but the topographies of the superfinished gears were essentially unchanged with running

ISBIS 2016: Meeting on Statistics in Business and Industry

This Book includes the abstracts of the talks presented at the 2016 International Symposium on Business and Industrial Statistics, held at Barcelona, June 8-10, 2016, hosted at the Universitat Politècnica de Catalunya - Barcelona TECH, by the Department of Statistics and Operations Research. The location of the meeting was at ETSEIB Building (Escola Tecnica Superior d'Enginyeria Industrial) at Avda Diagonal 647. The meeting organizers celebrated the continued success of ISBIS and ENBIS society, and the meeting draw together the international community of statisticians, both academics and industry professionals, who share the goal of making statistics the foundation for decision making in business and related applications. The Scientific Program Committee was constituted by: David Banks, Duke University Amílcar Oliveira, DCeT - Universidade Aberta and CEAUL Teresa A. Oliveira, DCeT - Universidade Aberta and CEAUL Nalini Ravishankar, University of Connecticut Xavier Tort Martorell, Universitat Politécnica de Catalunya, Barcelona TECH Martina Vandebroek, KU Leuven Vincenzo Esposito Vinzi, ESSEC Business Schoo

Inference for the process performance index of products on the basis of power-normal distribution

[[abstract]]The process performance index (PPI) can be a simple metric to connect the conforming rate of products. The properties of the PPI have been well studied for the normal distribution and other widely used lifetime distributions, such as the Weibull, Gamma, and Pareto distributions. Assume that the quality characteristic of product follows power-normal distribution. Statistical inference procedures for the PPI are established. The maximum likelihood estimation method for the model parameters and PPI is investigated and the exact Fisher information matrix is derived. We discuss the drawbacks of using the exact Fisher information matrix to obtain the confidence interval of the model parameters. The parametric bootstrap percentile and bootstrap bias-corrected percentile methods are proposed to obtain approximate confidence intervals for the model parameters and PPI. Monte Carlo simulations are conducted to evaluate the performance of the proposed methods. One example about the flow width of the resist in the hard-bake process is used for illustration.[[notice]]補正完