A design for testability study on a high performance automatic gain control circuit.

A comprehensive testability study on a commercial automatic gain control circuit is presented which aims to identify design for testability (DfT) modifications to both reduce production test cost and improve test quality. A fault simulation strategy based on layout extracted faults has been used to support the study. The paper proposes a number of DfT modifications at the layout, schematic and system levels together with testability. Guidelines that may well have generic applicability. Proposals for using the modifications to achieve partial self test are made and estimates of achieved fault coverage and quality levels presente

Fault simulation for structural testing of analogue integrated circuits

In this thesis the ANTICS analogue fault simulation software is described which provides a statistical approach to fault simulation for accurate analogue IC test evaluation. The traditional figure of fault coverage is replaced by the average probability of fault detection. This is later refined by considering the probability of fault occurrence to generate a more realistic, weighted test metric. Two techniques to reduce the fault simulation time are described, both of which show large reductions in simulation time with little loss of accuracy. The final section of the thesis presents an accurate comparison of three test techniques and an evaluation of dynamic supply current monitoring. An increase in fault detection for dynamic supply current monitoring is obtained by removing the DC component of the supply current prior to measurement

The integration of on-line monitoring and reconfiguration functions using IEEE1149.4 into a safety critical automotive electronic control unit.

This paper presents an innovative application of IEEE 1149.4 and the integrated diagnostic reconfiguration (IDR) as tools for the implementation of an embedded test solution for an automotive electronic control unit, implemented as a fully integrated mixed signal system. The paper describes how the test architecture can be used for fault avoidance with results from a hardware prototype presented. The paper concludes that fault avoidance can be integrated into mixed signal electronic systems to handle key failure modes

Low-overhead fault-tolerant logic for field-programmable gate arrays

While allowing for the fabrication of increasingly complex and efficient circuitry, transistor shrinkage and count-per-device expansion have major downsides: chiefly increased variation, degradation and fault susceptibility. For this reason, design-time consideration of faults will have to be given to increasing numbers of electronic systems in the future to ensure yields, reliabilities and lifetimes remain acceptably high. Many mathematical operators commonly accelerated in hardware are suited to modification resulting in datapath error detection and correction capabilities with far lower area, performance and/or power consumption overheads than those incurred through the utilisation of more established, general-purpose fault tolerance methods such as modular redundancy. Field-programmable gate arrays are uniquely placed to allow further area savings to be made thanks to their dynamic reconfigurability. The majority of the technical work presented within this thesis is based upon a benchmark hardware accelerator---a matrix multiplier---that underwent several evolutions in order to detect and correct faults manifesting along its datapath at runtime. In the first instance, fault detectability in excess of 99% was achieved in return for 7.87% additional area and 45.5% extra latency. In the second, the ability to correct errors caused by those faults was added at the cost of 4.20% more area, while 50.7% of this---and 46.2% of the previously incurred latency overhead---was removed through the introduction of partial reconfiguration in the third. The fourth demonstrates further reductions in both area and performance overheads---of 16.7% and 8.27%, respectively---through systematic data width reduction by allowing errors of less than ±0.5% of the maximum output value to propagate.Open Acces

What is the Path to Fast Fault Simulation?

Motivated by the recent advances in fast fault simulation techniques for large combinational circuits, a panel discussion has been organized for the 1988 International Test Conference. This paper is a collective account of the position statements offered by the panelists

Reduced Galloping Column Algorithm For Memory Testing

Memory testing is significantly important nowadays especially in SOC’s design, due to their rapid growth in the memory density and design complexity in smaller chip area and low power design. Thus, test time in memory testing is a key challenge to accelerate time to market, high yield and low test cost in high volume manufacturing. Test time reduction in memory testing is important in industry, as test cost is directly related to validation time of each product on the tester. There are lots of memory algorithms used for memory testing, including the galloping column algorithm (GalCol). The GalCol algorithm test is important to detect unique coupling and transition faults. However, the existing GalCol algorithm takes huge test time due to its test complexity. To overcome the test time issue in industry, reduced GalCol algorithms with solid data background are proposed. The reduced GalCol algoritms have similar test behavior as original GalCol algorithm with major difference in the number of galloping of the target cells. The galloping of target cells are reduced to first and last 8, 16 and 32 of cells of every base cell. This project is progressed in two stages, which are the software development using INTEL software and Synopsys tool and test implementation on INTEL production flow. These algorithm are verified on 15 units of 64KB L2 SRAM memory. In this project, test time reduction and consistent pass fail test results are achieved in the reduced GalCol algorithm tests. The GalCol X8 algorithm obtains the highest test time reduction of about 79.5% at 600MHz and 75.7% at 1.6GHz with consistent pass or fail test results comparable to original GalCol algorithm in the HVM test flow

Detection and Quantification of HspX Antigen in Sputum Samples Using Plasmonic Biosensing : Toward a Real Point-of-Care (POC) for Tuberculosis Diagnosis

Advancements that occurred during the last years in the diagnosis of Mycobacterium tuberculosis (Mtb), the causative agent of tuberculosis infection, have prompted increased survival rates of patients. However, limitations related to the inefficiency of an early detection still remain; some techniques and laboratory methods do not have enough specificity and most instruments are expensive and require handling by trained staff. In order to contribute to a prompt and effective diagnosis of tuberculosis, we report the development of a portable, user-friendly, and low-cost biosensor device for its early detection. By using a label-free surface plasmon resonance (SPR) biosensor, we have established a direct immunoassay for the direct detection and quantification of the heat shock protein X (HspX) of Mtb, a well-established biomarker of this pathogen, directly in pretreated sputum samples. The method relies on highly specific monoclonal antibodies that are previously immobilized on the plasmonic sensor surface. This technology allows for the direct detection of the biomarker without amplification steps, showing a limit of detection (LOD) of 0.63 ng mL-1 and a limit of quantification (LOQ) of 2.12 ng mL-1. The direct analysis in pretreated sputum shows significant differences in the HspX concentration in patients with tuberculosis (with concentration levels in the order of 116-175 ng mL-1) compared with non-tuberculosis infected patients (values below the LOQ of the assay)