2,993 research outputs found
Indoor wireless communications and applications
Chapter 3 addresses challenges in radio link and system design in indoor scenarios. Given the fact that most human activities take place in indoor environments, the need for supporting ubiquitous indoor data connectivity and location/tracking service becomes even more important than in the previous decades. Specific technical challenges addressed in this section are(i), modelling complex indoor radio channels for effective antenna deployment, (ii), potential of millimeter-wave (mm-wave) radios for supporting higher data rates, and (iii), feasible indoor localisation and tracking techniques, which are summarised in three dedicated sections of this chapter
Map-Aware Models for Indoor Wireless Localization Systems: An Experimental Study
The accuracy of indoor wireless localization systems can be substantially
enhanced by map-awareness, i.e., by the knowledge of the map of the environment
in which localization signals are acquired. In fact, this knowledge can be
exploited to cancel out, at least to some extent, the signal degradation due to
propagation through physical obstructions, i.e., to the so called
non-line-of-sight bias. This result can be achieved by developing novel
localization techniques that rely on proper map-aware statistical modelling of
the measurements they process. In this manuscript a unified statistical model
for the measurements acquired in map-aware localization systems based on
time-of-arrival and received signal strength techniques is developed and its
experimental validation is illustrated. Finally, the accuracy of the proposed
map-aware model is assessed and compared with that offered by its map-unaware
counterparts. Our numerical results show that, when the quality of acquired
measurements is poor, map-aware modelling can enhance localization accuracy by
up to 110% in certain scenarios.Comment: 13 pages, 11 figures, 1 table. IEEE Transactions on Wireless
Communications, 201
Implementation Aspects of a Transmitted-Reference UWB Receiver
In this paper, we discuss the design issues of an ultra wide band (UWB) receiver targeting a single-chip CMOS implementation for low data-rate applications like ad hoc wireless sensor networks. A non-coherent transmitted reference (TR) receiver is chosen because of its small complexity compared to other architectures. After a brief recapitulation of the UWB fundamentals and a short discussion on the major differences between coherent and non-coherent receivers, we discuss issues, challenges and possible design solutions. Several simulation results obtained by means of a behavioral model are presented, together with an analysis of the trade-off between performance and complexity in an integrated circuit implementation
Experimental evaluation of UWB indoor positioning for indoor track cycling
Accurate radio frequency (RF)-based indoor localization systems are more and more applied during sports. The most accurate RF-based localization systems use ultra-wideband (UWB) technology; this is why this technology is the most prevalent. UWB positioning systems allow for an in-depth analysis of the performance of athletes during training and competition. There is no research available that investigates the feasibility of UWB technology for indoor track cycling. In this paper, we investigate the optimal position to mount the UWB hardware for that specific use case. Different positions on the bicycle and cyclist were evaluated based on accuracy, received power level, line-of-sight, maximum communication range, and comfort. Next to this, the energy consumption of our UWB system was evaluated. We found that the optimal hardware position was the lower back, with a median ranging error of 22 cm (infrastructure hardware placed at 2.3 m). The energy consumption of our UWB system is also taken into account. Applied to our setup with the hardware mounted at the lower back, the maximum communication range varies between 32.6 m and 43.8 m. This shows that UWB localization systems are suitable for indoor positioning of track cyclists
An indoor variance-based localization technique utilizing the UWB estimation of geometrical propagation parameters
A novel localization framework is presented based on ultra-wideband (UWB) channel sounding, employing a triangulation method using the geometrical properties of propagation paths, such as time delay of arrival, angle of departure, angle of arrival, and their estimated variances. In order to extract these parameters from the UWB sounding data, an extension to the high-resolution RiMAX algorithm was developed, facilitating the analysis of these frequency-dependent multipath parameters. This framework was then tested by performing indoor measurements with a vector network analyzer and virtual antenna arrays. The estimated means and variances of these geometrical parameters were utilized to generate multiple sample sets of input values for our localization framework. Next to that, we consider the existence of multiple possible target locations, which were subsequently clustered using a Kim-Parks algorithm, resulting in a more robust estimation of each target node. Measurements reveal that our newly proposed technique achieves an average accuracy of 0.26, 0.28, and 0.90 m in line-of-sight (LoS), obstructed-LoS, and non-LoS scenarios, respectively, and this with only one single beacon node. Moreover, utilizing the estimated variances of the multipath parameters proved to enhance the location estimation significantly compared to only utilizing their estimated mean values
D-SLATS: Distributed Simultaneous Localization and Time Synchronization
Through the last decade, we have witnessed a surge of Internet of Things
(IoT) devices, and with that a greater need to choreograph their actions across
both time and space. Although these two problems, namely time synchronization
and localization, share many aspects in common, they are traditionally treated
separately or combined on centralized approaches that results in an ineffcient
use of resources, or in solutions that are not scalable in terms of the number
of IoT devices. Therefore, we propose D-SLATS, a framework comprised of three
different and independent algorithms to jointly solve time synchronization and
localization problems in a distributed fashion. The First two algorithms are
based mainly on the distributed Extended Kalman Filter (EKF) whereas the third
one uses optimization techniques. No fusion center is required, and the devices
only communicate with their neighbors. The proposed methods are evaluated on
custom Ultra-Wideband communication Testbed and a quadrotor, representing a
network of both static and mobile nodes. Our algorithms achieve up to three
microseconds time synchronization accuracy and 30 cm localization error
Massive MIMO-based Localization and Mapping Exploiting Phase Information of Multipath Components
In this paper, we present a robust multipath-based localization and mapping
framework that exploits the phases of specular multipath components (MPCs)
using a massive multiple-input multiple-output (MIMO) array at the base
station. Utilizing the phase information related to the propagation distances
of the MPCs enables the possibility of localization with extraordinary accuracy
even with limited bandwidth. The specular MPC parameters along with the
parameters of the noise and the dense multipath component (DMC) are tracked
using an extended Kalman filter (EKF), which enables to preserve the
distance-related phase changes of the MPC complex amplitudes. The DMC comprises
all non-resolvable MPCs, which occur due to finite measurement aperture. The
estimation of the DMC parameters enhances the estimation quality of the
specular MPCs and therefore also the quality of localization and mapping. The
estimated MPC propagation distances are subsequently used as input to a
distance-based localization and mapping algorithm. This algorithm does not need
prior knowledge about the surrounding environment and base station position.
The performance is demonstrated with real radio-channel measurements using an
antenna array with 128 ports at the base station side and a standard cellular
signal bandwidth of 40 MHz. The results show that high accuracy localization is
possible even with such a low bandwidth.Comment: 14 pages (two columns), 13 figures. This work has been submitted to
the IEEE Transaction on Wireless Communications for possible publication.
Copyright may be transferred without notice, after which this version may no
longer be accessibl
A New Reduction Scheme for Gaussian Sum Filters
In many signal processing applications it is required to estimate the
unobservable state of a dynamic system from its noisy measurements. For linear
dynamic systems with Gaussian Mixture (GM) noise distributions, Gaussian Sum
Filters (GSF) provide the MMSE state estimate by tracking the GM posterior.
However, since the number of the clusters of the GM posterior grows
exponentially over time, suitable reduction schemes need to be used to maintain
the size of the bank in GSF. In this work we propose a low computational
complexity reduction scheme which uses an initial state estimation to find the
active noise clusters and removes all the others. Since the performance of our
proposed method relies on the accuracy of the initial state estimation, we also
propose five methods for finding this estimation. We provide simulation results
showing that with suitable choice of the initial state estimation (based on the
shape of the noise models), our proposed reduction scheme provides better state
estimations both in terms of accuracy and precision when compared with other
reduction methods
- …